Sony BDP-S1700ES / BDP-S770 Service Manual ▷ View online
1-22
1-5. HARNESS AND USB DRESSING
1-5-1. Harness (SIM-001)
- Harness (SIM-001) MUST ALWAYS under the board to board connector
1-5-2. USB (USB-007)
- USB Harness ALWAYS place on the chasis by using Non-Halogen tape
Follow the designated destination according to the mark indicated on the board
1-6. Power Cord Soldering location
1-6-1. Soldering point for Switching Regulator (APS-257)
1-6-2. Soldering point for Switching Regulator (SRV2206UC)
- (BDP-S770/S1700ES : EXCEPT US, CND)
Mount the Power Supply Cord as indicated
- (BDP-S770/S1700ES: US, CND Only)
Mount the Power Supply Cord as indicated
BDP-S770/S1700ES
1-23E
1-7. Avoid Switching Regulator Board from floating
Stick the Non-Halogene tape
as shown. Make sure the tape
is strongly stick to both of
MB-134 board and Switching
Regulation board.
1-8. Remove PT Protection on MB-134 (Service Assy Main Board)
PT Protector (4-186-977-01) stick on B-side to protect PT107 (1-780-638-22)
PT Protector need to be remove before installing the MB board on chassis
PT Protector need to be remove before installing the MB board on chassis
PT Protector (P/N 4-186-977-01)
PT 107 (P/N 1-780-638-22)
BDP-S770/S1700ES
2-1
BDP-S770/S1700ES
SECTION 2
DISASSEMBLY
• This set can be disassembled in the order shown below.
Note: Follow the disassembly procedure in the numerical order given.
2-2. PANEL TOP
2-1. DISASSEMBLY FLOW
2-2. PANEL TOP
(Page 2-1)
2-3. FRONT PANEL BLOCK
(Page 2-2)
2-4. BD DRIVE
(Page 2-2)
2-7. REAR PANEL BLOCK
(Page 2-4)
2-5. WIRELESS LAN CARD BLOCK
(Page 2-3)
2-8. SWITCHING REGULATOR
(Page 2-5)
2-6. MB-134 BOARD,
HU-015 BOARD
(Page 2-4)
SET
4 Panel Top
1 Three Tapping Screws
(tightening torque = 5 to 6kgf.cm)
6
Top Shield
2 Side Panel Left
3 Side Panel Right
5 Three Tapping Screws
(tightening torque = 5 to 6kgf.cm)
EM-002 BOARD, IR-071 BOARD
2-2
2-3. FRONT PANEL BLOCK
BDP-S770/S1700ES
6
Front Panel Block
Tray cover assy
1
8 Claws
5
2-4. BD DRIVE
Two Coaxial
Cables
3
gray
black
4
USB Cables
(CN102)
1
Four Screws (BV3)
(tightening torque = 6.0 to 7.0 kgf•cm)
2
Flexible Flat Cable(Optical)
(CN1401)
3
(CN2460)
Flexible Flat Cable(Spindle)
4
(CN2470)
Flexible Flat Cable(Loading)
5
BD drive
Tapping Screws (BV3)
(tightening torque = 5.0 to 6.0
2
Click on the first or last page to see other BDP-S1700ES / BDP-S770 service manuals if exist.