Sony SAL85F14Z Service Manual ▷ View online
2-1
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
2-1.
DISASSEMBLY
2-1-1. 1ST BALL FRAME (A) LENS BLOCK AND MIRROR TUBE BLOCK
HELP04
HELP03
HELP02
HELP01
EXPLODED VIEW
5
1st Ball Frame (A)
Lens Block
4
Front Ring
3
Lens (G1)
2
G1 Stopper
Click pin
1
G1 Decoration Plate
Note:
• Before removing the G1 decoration plate,
apply the solvent (alcohl) to a gap between
G1 decoration plate and front ring a little
and then dissolve the adhesive bond (B-10).
Remove the G1 decoration plate using the
name ring wrench (72mm), to prevent the
damage it.
• Before removing the G1 decoration plate,
apply the solvent (alcohl) to a gap between
G1 decoration plate and front ring a little
and then dissolve the adhesive bond (B-10).
Remove the G1 decoration plate using the
name ring wrench (72mm), to prevent the
damage it.
Name ring wrench (72 mm):
J-6082-634-A
• Be sure avoiding replacement of G1
decoration plate as far as possible.
If replacement of it should be need, you
convey the message to your user that
changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user’s
agreement, and it replace.
decoration plate as far as possible.
If replacement of it should be need, you
convey the message to your user that
changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user’s
agreement, and it replace.
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
2-3
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
2-1-2. LENS MOUNT BLOCK
A
A
C
E
D
B
D
C
B
E
1
Connection Box
Preset Ring
Main SP
2
Rear Light Shield Barrel
Lens Mount Rivetting Block
3
5
Coupler
FLANGE BACK (f’F)
ADJUSTMENT
ADJUSTMENT
FLANGE BACK (f’F)
ADJUSTMENT
ADJUSTMENT
HELP05
HELP06
HELP07
HELP08
Preset Ring
Holding Plate
Holding Plate
Lens Mount Block
Coupler Adjustment
Washer (A to E)
Washer (A to E)
4
Back Adjustment Washer
(A to E)
EXPLODED VIEW
2-4
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
2-1-3. GEAR BASE PLATE (A) BLOCK, BRUSH AND FIXED HOLDING TUBE BLOCK
HELP09
HELP13
HELP10
HELP12
HELP11
1
Fixed Holding Tube Block
5
Brush Block
2
Gear Base Plate (A) Block
4
Cam Tube
Reinforcement
Plate
Plate
Brush Hold Plate
Brush
Brush Base Plate
3
Focus Scale Plate
Guide Pin
Polyester Tape (Black) 10 mm
Polyester Tape (Black) 10 mm
HELP12
4
Cam Tube
Reinforcement
Plate
Plate
EXPLODED VIEW
BRUSH POSITION ADJUSTMENT
Note:
In case of the focus ring is the old type and replace
the cam tube reinforcement plate, affix the polyester
tape (black) 10mm one time around the cam tube
reinforcement plate as shown in figure.
the cam tube reinforcement plate, affix the polyester
tape (black) 10mm one time around the cam tube
reinforcement plate as shown in figure.
Cam Tube
Reinforcement
Plate
Reinforcement
Plate
Focus Cam Tube
Polyester Tape
(Black) 10mm
(Black) 10mm
Cam Tube
Reinforcement
Plate
Reinforcement
Plate
Ver. 1.4 2008.01
The changed portions from
Ver. 1.3 are shown in blue.
Ver. 1.3 are shown in blue.
Click on the first or last page to see other SAL85F14Z service manuals if exist.