Sony SAL85F14Z Service Manual ▷ View online
1-3
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
1-7.
TROUBLESHOOTING
1-7-1. Aperture Trouble
NG
Check operation of
the preset ring.
Replace the lens
mount block.
Check operation of the
lens mount block,
and replace the
defective part.
Perform the aperture
diameter adjustment.
(See page 4-16.)
Perform the aperture
diameter check.
(See page 4-13.)
NG
Check operation
of aperture of the
1st moving barrel frame.
OK
OK
OK
Function NG
F No. NG
Aperture trouble
Replace the defective part.
NG
NG
NG
END
OK
Perform the aperture
diameter check.
(See page 4-13.)
1-4
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
1-7-2. Foucus Trouble
Check the operation
again.
Replace the defective part
or apply the grease.
OK
NG
OK
OK
OK
OK
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the coupler,
gear base plate
(A) block.
Check the focus cam
ring and fixed barrel
block.
NG
NG
NG
NG
NG
END
OK
Check the position
and deformation
at the tip of the brush.
Adjust the position, or
replace the brush.
Check pattern
of the main flexible unit.
Clean the pattern of the
main flexible unit.
Replace the
main flexible unit.
Perform the
brush position
check/adjustment.
(See page 4-28.)
2-1
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL85F14Z (Planar 1.4/85) (Planar T
*
85mm F1.4 ZA)
2-1.
DISASSEMBLY
2-1-1. 1ST BALL FRAME (A) LENS BLOCK AND MIRROR TUBE BLOCK
HELP04
HELP03
HELP02
HELP01
EXPLODED VIEW
5
1st Ball Frame (A)
Lens Block
4
Front Ring
3
Lens (G1)
2
G1 Stopper
Click pin
1
G1 Decoration Plate
Note:
• Before removing the G1 decoration plate,
apply the solvent (alcohl) to a gap between
G1 decoration plate and front ring a little
and then dissolve the adhesive bond (B-10).
Remove the G1 decoration plate using the
name ring wrench (72mm), to prevent the
damage it.
• Before removing the G1 decoration plate,
apply the solvent (alcohl) to a gap between
G1 decoration plate and front ring a little
and then dissolve the adhesive bond (B-10).
Remove the G1 decoration plate using the
name ring wrench (72mm), to prevent the
damage it.
Name ring wrench (72 mm):
J-6082-634-A
• Be sure avoiding replacement of G1
decoration plate as far as possible.
If replacement of it should be need, you
convey the message to your user that
changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user’s
agreement, and it replace.
decoration plate as far as possible.
If replacement of it should be need, you
convey the message to your user that
changing of the “Carl Zeiss Serial No.” is
needed, and then you may obtain user’s
agreement, and it replace.
Ver. 1.3 2007.10
The changed portions from
Ver. 1.2 are shown in blue.
Ver. 1.2 are shown in blue.
Click on the first or last page to see other SAL85F14Z service manuals if exist.