DOWNLOAD Sony SAL70400G2 Service Manual ↓ Size: 8.56 MB | Pages: 66 in PDF or view online for FREE

Model
SAL70400G2
Pages
66
Size
8.56 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
sal70400g2.pdf
Date

Sony SAL70400G2 Service Manual ▷ View online

Sony Corporation
Revision History
SAL70400G2 (4-5.6/70-400 G SSM 
Ⅱ) (70-400mm F4-5.6 G SSM Ⅱ)
SERVICE MANUAL
Link (English)
 
 SPECIFICATIONS
 
 DISASSEMBLY
 
 ADJUSTMENTS
 
 SERVICE NOTE
 
 REPAIR PARTS LIST
Link (Japanese)
 
 SPECIFICATIONS
 
 DISASSEMBLY
 
 ADJUSTMENTS
 
 SERVICE NOTE
 
 REPAIR PARTS LIST
983472313.pdf
2015G08-1
  © 2015.07
Published by Sony Techno Create Corporation
INTERCHANGEABLE LENS
9-834-723-13
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2013.02
Official Release
1.1
2013.03
Revised-1
(A1 12-350)
•  Correction of the Image of the Lens.
 Page 
Top 
cover
 English:   
Page 
2-2
,
 2-3
,
 2-4
,
 2-5
,
 2-6
,
 2-7
,
 2-9
,
 2-10
,
 3-1
,
 3-2
,
 4-1
,
 4-3
,
 
4-4
,
 4-5
,
 4-6
,
 4-8
,
 4-10
 Japanese:  
Page 
2-2
,
 2-3
,
 2-4
,
 2-5
,
 2-6
,
 2-7
,
 2-9
,
 2-10
,
 4-1
,
 4-3
,
 4-4
,
 4-5
,
 
4-6
,
 4-8
,
 4-10
• Correction of ADJUSTMENTS.
 English:   
Page 
4-5
,
 4-7
,
 4-11
 Japanese:  
Page 
4-5
,
 4-7
,
 4-11
Yes
1.2
2015.07
Revised-2
(A2 14-331)
• Change of ADJUSTMENTS.
 English:  Page 
4-1
 
 Japanese: Page 
4-1
Yes
SAL70400G2
      (4-5.6/70-400 G SSM ) (70-400mm F4-5.6 G SSM )
Ver. 1.2  2015.07
US Model
Canadian Model
AEP Model
Chinese Model
Japanese Model
•  About the Lens Test Projector and Finished Inspection JIG
• 
レンズ投影器と完成検査治具について
分解図につきましては,英語版を
ご参照下さい。
Revision History
Revised-2
Replace the previously issued
SERVICE MANUAL 9-834-723-12
with this Manual.
– 2 –
SAL70400G2 (4-5.6/70-400 G SSM Ⅱ) (70-400mm F4-5.6 G SSM Ⅱ)
– ENGLISH –
– JAPANESE –
SPECIFICATIONS
•  This lens is equipped with a distance encoder. The distance encoder allows more accurate measurement (ADI) by using an ADI-compatible flash.
•  Depending on the lens mechanism, the focal length may change with any change of the shooting distance. The focal length assumes the lens is 
focused at infinity.
Equivalent 35mm-format focal length
*
1
 (mm)
 105-600
Lens groups-elements
 
 12-18
Angle of view 1
*
2
 
 34°-6°10’
Angle of view 2
*
2
 
 23°-4°10’
Minimum focus
*
3
(m (feet))
 
 1.5 
(5)
Maximum magnification (
×
)
 
 0.27
Minimum f-stop 
 f/22-f/32
Filter diameter (mm)
 
 77
Dimensions (maximum diameter 
×
 height) (Approx., mm (in.))
 
94.5 × 196 (3 3/4 × 7 3/4)
Mass (Approx., g (oz)) 
 1,500 
(53)
*1  The equivalent 35mm-format focal length shown above is for Interchangeable Lens Digital Cameras equipped with an APS-C sized image sensor.
*2  The angle of view 1 is for 35mm-format cameras, and the angle of view 2 is for Interchangeable Lens Digital Cameras equipped with an APS-C 
size image sensor.
*3  Minimum focus is the shortest distance from the image sensor to the subject.
Included items
 
Lens (1), Front lens cap (1), Rear lens cap (1), Lens hood (1), Lens case (1), Set of printed documentation
Design and specifications are subject to change without notice.
概略仕様
・  このレンズは距離エンコーダーを搭載しています。距離エンコーダーとは、 高精度な調光(ADI調光)をADI対応フラッシュとの組み
合わせで実現する機能です。
・  レンズの機構によっては、撮影距離の変化に伴って焦点距離が変化する場合があります。記載の焦点距離は撮影距離が無限遠での
定義です。
35mm
判換算焦点距離
*
1
 
mm
 
105-600
レンズ群一枚
 
12-18
画角
1
*
2
 
 
34° -6° 10
画角
2
*
2
 
 
23° -4° 10
最短撮影距離
*
3
m
) 
 
1.5
最大撮影倍率(倍) 
 
0.27
最小絞り
 
F22-F32
フィルター径(
mm
) 
 
77
外形寸法(最大径×長さ)
(約:
mm
 
94.5×196
質量(約:
g
) 
 
1,500
*1  ここでの35mm判換算焦点距離とは、APS-Cサイズ相当の撮像素子を搭載したレンズ交換式デジタルカメラでの値を表します。
*2  画角1は35mm判カメラ、画角2はAPS-Cサイズ相当の撮像素子を搭載したレンズ交換式デジタルカメラでの値を表します。
*3  最短撮影距離とは、撮像素子面から被写体までの最短距離を表します。
同梱物
 
レンズ(1)、レンズフロントキャップ(1)、レンズリヤキャップ(1)、レンズフード(1)、レンズケース(1)、印刷物一式
仕様および外観は、改良のため予告なく変更することがありますが、ご了承ください。
SAL70400G2 (4-5.6/70-400 G SSM Ⅱ) (70-400mm F4-5.6 G SSM Ⅱ)
1-1
1. SERVICE NOTE
1-1. Chemicals
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health and environment, and wastes resources.
Manage the chemicals carefully as follows.
•  Store chemicals sealed in a specific place to prevent from exposure to high temperature or direct sunlight.
•  Avoid dividing chemicals into excessive numbers of small containers to reduce natural evaporation.
•  Keep containers sealed to avoid natural evaporation when chemicals are not in use.
•  Avoid using chemicals as much as possible. When using chemicals, divide only required amount to a small plate from the container and 
use up it.
1-2. Exterior Parts
Be careful to the following points for exterior parts used in this unit.
•  Use a piece of cleaning paper or cleaning cloth for cleaning exterior parts. Avoid using chemicals.
Even if you have to use chemicals to clean heavy dirt, don t use paint thinner, ketone, nor alcohol.
•  Insert the specific screws vertically to the part when installing a exterior part.
Be careful not to tighten screws too much.
1-3. Unleaded Solder
This unit uses unleaded solder.
Boards requiring use of unleaded solder are printed with the lead free mark (LF) indicating the solder contains no lead.
(
Caution:
 Some printed circuit boards may not come printed with the lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•  Set the soldering iron tip temperature to 350  C approximately.
If cannot control temperature, solder/unsolder at high temperature for a short time.
Caution:
   The printed pattern (copper foil) may peel away if the heated tip is applied for too long, so be careful!
Unleaded solder is more viscous (sticky, less prone to flow) than ordinary solder so use caution not to let solder bridges occur such as on IC 
pins, etc.
•  Be sure to control soldering iron tips used for unleaded solder and those for leaded solder so they are managed separately. Mixing un-
leaded solder and leaded solder will cause detachment phenomenon.
1-4. SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1.  Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are  pinched  or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the cus-
tomer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
•  Set the soldering iron tip temperature to 350  C approximately.
•  Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
•  Be careful not to apply force on the conductor when soldering or unsoldering.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE 
WITH MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN 
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. 
REPLACE THESE COMPONENTS WITH SONY PARTS 
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS 
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY. 
ATTENTION AU COMPOSANT AYANT RAPPORT 
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES DIAGRAMMES SCHÉMATIQUES ET LA 
LISTE DES PIÈCES SONT CRITIQUES POUR L A 
SÉCURITÉ DE FONCTIONNEMENT. NE REMPLACER CES 
COMPOSANTS QUE PAR DES PIÈSES SONY DONT LES 
NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS 
LES SUPPÉMENTS PUBLIÉS PAR SONY.
– ENGLISH –
2-1
SAL70400G2 (4-5.6/70-400 G SSM Ⅱ) (70-400mm F4-5.6 G SSM Ⅱ)
2. DISASSEMBLY
NOTE FOR REPAIR
•  Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
•  When remove a connector, don t pull at wire of connector. It is possible that a wire is snapped.
•  When installing a connector, don t press down at wire of connector.
It is possible that a wire is snapped.
•  Do not apply excessive load to the gilded flexible board.
Notches
Holes
How to Use
Attach the chip-A, chip-B or chip-C to the universal wrench.
For the notches:
For the holes:
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc. during disassembling/
assembling the lens, Use the universal wrench.
chip-A, chip-C
chip-B
Universal wrench
J-6082-609-A
Chip-A for 
universal wrench:
J-6082-609-1
Chip-B for 
universal wrench:
J-6082-609-2
Chip-C for
universal wrench:
J-6082-609-3
Notches
Holes
Chip
Chip-A
or
Chip-C
Chip-A
or
Chip-C
Chip-B
Chip-B
Chip
Match the universal wrench to the holes or notches of the lens block, etc.
Match the universal wrench
to the width of holes or notches.
Universal wrench
LOCTITE 460 or
the equivalent
LOCTITE 460 or
the equivalent
A-20
B-10
G-62
G-85
G-116
G-48
B-40
B-60
B-110
SERVICE TOOLS
J-6082-669-A
J-6082-670-A
J-6082-626-A
J-6082-628-A
Grease (G-48):
Grease (G-62):
Grease (G-85):
Grease (G-116):
J-6082-611-A
J-6082-612-A
J-6082-614-A
J-6082-616-A
J-6082-617-A
Anti-diffusion agent (A-20):
Adhesive bond (B-10):
Adhesive bond (B-40):
Adhesive bond (B-60):
Adhesive bond (B-110):
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Page of 66
Display

Sony SAL70400G2 Service Manual ▷ Download

  • DOWNLOAD Sony SAL70400G2 Service Manual ↓ Size: 8.56 MB | Pages: 66 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony SAL70400G2 in PDF for free, which will help you to disassemble, recover, fix and repair Sony SAL70400G2 Digital Camera. Information contained in Sony SAL70400G2 Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.