Sony SAL70200G (serv.man2) Service Manual ▷ View online
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
Note for assembling and grease applying positions are shown.
HELP01
Grease (G-85):
J-6082-626-A
Adhesive (Adhesive ivory white):
Note:
Use the glue (adhesive ivory white) or the equivalent
1.
Affix the tripod mount friction sheet to the tripod mount as shown in the figure.
Note:
Affix the tripod mount friction sheet, starting from the cut portion. Do not cover the cut portion with the tripod mount
friction sheet.
2.
Apply the grease (G-85) to the mating face of tripod mount knob and screw portion. Then, insert the tripod mount knob as far as it
goes to the tripod mount.
3.
After tightening the screw to the extent that the tripod mount knob comes off, turn it back half turn (Loosen).
4.
Apply the adhesive (adhesive ivory white) to the indicated portion.
Note:
It is not necessary to fill the screw hole with the adhesive. Apply the adhesive to the head of screw and hole.
HELP
Tripod Mount
Cut portion
Cut view
Cut view
Tripod Mount Friction Sheet
Apply the Grease
(G-85)
(G-85)
Apply the adhesive bond
(Adhesive ivory white)
(Adhesive ivory white)
Tripod Mount Knob
Tripod Mount
Tripod
Mount
Mount
Tripod Mount Knob
Screw
Screw
Ver. 1.3 2009.02
The changed portions from
Ver. 1.2 are shown in blue.
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP02
Mount the tripod washer block to the lens body, aligning the mount index with the red mark on the tripod mount.
Tripod Washer Block
Mount Index
Red mark on the Tripod Mount
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
HELP03
Anti-diffusion agent (A-20):
J-6082-611-A
Adhesive bond (B-40):
J-6082-614-A
Adhesive (adhesive ivory white)
Note:
Use the adhesive (adhesive ivory white) or the equivalent.
1.
Apply the anti-diffusion agent (A-20) to the indicated portion (all circumferences) of outer barrel.
2.
Install the outer barrel, aligning the DM PC board unit with the switch base plate block installation window.
3.
Connect the connector of switch base plate block to the DM PC board unit.
4.
Rotate the outer barrel in the arrow direction so that the mount index is aligned with the length hole.
5.
Apply the adhesive bond (B-40) to tips of four screws and fix the switch base plate block with four screws.
6.
Paint the cross-slot on the head of screw. (Four locations)
Note:
The white paint should not leak from the cross-slot.
Outer Barrel
Outer Barrel
Connector of
switch base plate block
switch base plate block
Cut view
Inside
Outside
Cut
view
view
Apply the anti-diffusion
agent (A-20) (All round)
agent (A-20) (All round)
Switch base plate
block installation
window
block installation
window
DM PC Board Unit
DM PC Board Unit
Apply the white paint
Rotate the outer barrel
Length hole
Mount Index
Apply the
adhesive
bond (B-40)
adhesive
bond (B-40)
HELP
SAL70200G (2.8/70-200 G) (70-200mm F2.8 G)
7.
Set the zoom operation ring to the WIDE end.
8.
Apply the adhesive bond (B-40) to the tips of four screws and fix the outer barrel with four screws tentatively to the extent that the
outer barrel moves a little in the rotational direction.
9.
Align “70” on the zoom scale with the center of index of outer barrel and tighten four screw firmly.
10. Push the outer barrel to the 1st lens and tighten the outer barrel with three slotted head paling end screws.
Then, apply the adhesive (adhesive ivory white) to head of screws (Three locations).
Note:
The adhesive (adhesive ivory white) should not seep out.
Set to the wide
end position
end position
Zoom Operation Ring
Fix with four screws tentatively
to the extent that the outer barrel
moves a little in the rotational direction.
to the extent that the outer barrel
moves a little in the rotational direction.
Apply the
adhesive bond
(B-40)
adhesive bond
(B-40)
Apply the
adhesive bond
(B-40)
adhesive bond
(B-40)
Tighten three paling end screws and
apply the adhesive (adhesive ivory white)
to the head.
apply the adhesive (adhesive ivory white)
to the head.
Align the position and
tighten the screws firmly.
tighten the screws firmly.
Index
Click on the first or last page to see other SAL70200G (serv.man2) service manuals if exist.