Sony SAL50M28 Service Manual ▷ View online
1-3
SAL50M28 (MACRO 2.8/50) (50mm F2.8 Macro)
1-5.
TROUBLESHOOTING
1-5-1. Aperture Trouble
Ver 1.1 2007.02
NG
Check operation of
the preset ring.
Replace the defective part.
Check operation of the
preset ring, and replace
the defective part.
Perform the aperture
diameter adjustment.
(See page 4-7.)
Perform the aperture
diameter check.
(See page 4-4.)
NG
Check operation of the
aperture control block.
OK
OK
OK
Function NG
F No. NG
Aperture trouble
Replace the defective part.
NG
NG
NG
END
OK
Perform the aperture
diameter check.
(See page 4-4.)
1-4
SAL50M28 (MACRO 2.8/50) (50mm F2.8 Macro)
1-5-2. Foucus Trouble
Check the operation
again.
Replace the defective part
or apply the grease.
OK
NG
OK
OK
OK
OK
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the coupler and
gear block.
Check the fixed holding
tube block and
fixed barrel unit.
NG
NG
NG
NG
NG
END
OK
Check the position
and deformation
at the tip of the
A encoder brush.
Adjust the position, or replace
the A encoder brush.
Check pattern
of the main flexible block.
Clean the pattern of the
main flexible block.
Replace the
main flexible block.
Perform the
brush position
check/adjustment.
(See page 4-17.)
2-1
SAL50M28 (MACRO 2.8/50) (50mm F2.8 Macro)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
When top of tip does not reach holes or notches because the fixed screw becomes obstructive,
replace the fixed screw to below.
+B 3X5 7-682-546-09
replace the fixed screw to below.
+B 3X5 7-682-546-09
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Ver 1.1 2007.02
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL50M28 (MACRO 2.8/50) (50mm F2.8 Macro)
2-1.
DISASSEMBLY
2-1-1. FRONT LENS BARREL AND MOUNT RIVETING BLOCK
(See Page 2-3.)
A
A
EXPLODED VIEW
3
Main Flexible Block
6
Back Adjustment
Washer
HELP01
HELP04
4
Rear Light
HELP02
7
Coupler
HELP05
5
Mount
Riveting
Block
Block
HELP03
1
Front Light
2
Front Lens
Barrel
Note:
Attach the decollation ring after cleaning the
attaching surface of the middle barrel.
Attach the decollation ring after cleaning the
attaching surface of the middle barrel.
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
Shield Barrel
Shield Barrel
Note:
Remove the front light shield barrel
using the name ring wrench A (49mm).
Remove the front light shield barrel
using the name ring wrench A (49mm).
Name ring wrench A (49mm):
J-6082-586-A
J-6082-586-A
Name ring wrench A (49mm)
HELP38
Click on the first or last page to see other SAL50M28 service manuals if exist.