DOWNLOAD Sony SAL50F14Z Service Manual ↓ Size: 11.7 MB | Pages: 55 in PDF or view online for FREE

2-3

The following shows notes for assembling and grease applying positions.

SAL50F14Z (Planar 1,4/50 ZA) (Planar T*50mm F1.4 ZA SSM)

Bond (B-10) : J-6082-612-A

1.   Cut the tip of new brush with nippers.
2.   Install the brush and fix it with one screw.
3.   After adjusting the brush position, apply adhesive bond (B-10) to the head of screw.

Brush

Cut with nippers.

Screw (M1.6) 
Tightening torque:

0.06 

± 0.01 N.m

Apply adhesive 
bond (B-10) 

Bond (B-10) : J-6082-612-A

1.   Install the two washers and the GMR flexible board, and tighten two screws.

 When installing the GMR flexible board, tighten two screws to the specified tightening torque paying attention not to deform it.

2.   Apply adhesive bond (B-10) to the head of screws.
 

Screws (B1.7 x 3) 
Tightening torque:

0.12 

± 0.01 N.m

GMR Flexible Board

Washers

Apply adhesive 
bond (B-10)

Bond (B-10) : J-6082-612-A

1.   Install the sensor ring block assy and three washers, and tighten three screws.
2.   Apply bond (B-10) to fix the screws, washers, and the sensor ring block assy.
 

Washer

Sensor Ring Block ASSY

Apply adhesive
bond (B-10)

2-4

SAL50F14Z (Planar 1,4/50 ZA) (Planar T*50mm F1.4 ZA SSM)

Bond (B-10) : J-6082-612-A

1.   Stick the gasket as shown below and apply bond (B-10) to fix the fixed barrel block assy and the gasket.

Gasket

Apply adhesive
bond (B-10)

Fixed Barrel Block ASSY

 

1.   Install a back washer at the position shown below, and tighten three screws.
 

Back Washer

1.   Overlap back adjustment washers with the B/L flexible board as shown below, and secure them.
 

Back Adjustment Washers

B/L Flexible Board

Grease (O-20): J-6082-610-A

1.   Dip the main spring in grease (O-20) and dry it for about five minutes.

Dip Main Spring 
in grease (O-20).

Main Spring

2-5

SAL50F14Z (Planar 1,4/50 ZA) (Planar T*50mm F1.4 ZA SSM)

Anti-diffusion agent (A-20): J-6082-611-A

1.   Apply anti-diffusion agent (A-20) to the back side of the mount (lens A mount).
 

Apply anti-diffusion
agent (A-20)

Mount (Lens A  Mount)

1.   While engaging the U-shaped groove of the mount block assy with the Aperture Interlocking Pin, install the mount block assy.
2.   Tighten screws (1), (2), (3), and (4) in this order.
 

Mount Block ASSY

Aperture Interlocking Pin

3

4

2

1

U-shaped groove of 
Mount Block ASSY

Grease (G-35): J-6082-621-A

1.   Apply grease (G-35) to the inner diameter surface of the function ring block assy.
 

Apply grease
(G-35)

Function Ring 
Block ASSY

Grease (G-35): J-6082-621-A

1.   Apply grease (G-35) to the inner diameter surface and the working face of the rotor interlocking ring.
 

Apply grease
(G-35)

Rotor Interlocking 
Ring

Inner diameter

Working face

 

2-6

SAL50F14Z (Planar 1,4/50 ZA) (Planar T*50mm F1.4 ZA SSM)

1.   Stick the SSM holding sheet with the R-cut portion of the plate (pressure plate) facing down.
 

Plate (Pressure Plate)

SSM Holding Sheet

Adhesive surface

R-cut portion

Grease (FT-210): 9-913-200-37

1.   Dip the spring in grease (FT-210).
2.   Install the spring with its burr side facing down so that the ridge of the spring comes to the center of the flexible board.
 

Flexible Board

Flexible Board

Spring

Spring

Apply grease
(FT-210)

Ridge

Bond (B-10) : J-6082-612-A

1.  Install the SSM holding plate while matching its cutouts with the focus stopper pins.
2.   Turn the SSM holding plate counterclockwise about 30 degrees.

Focus Stopper Pins

about 30

SSM Holding Plate

3.   Apply bond (B-10) to fix the focus stopper pins, SSM holding plate, and straight moving barrel.
 

Focus Stopper Pin

SSM Holding 
Plate

Apply grease
(B-10)

Straight Moving 
Barrel

Grease (FT-210): 9-913-200-37

1.   Apply grease (FT-210) to the indicated portion of the front ring.
 

Apply grease
(FT-210)

Front Ring