Sony SAL500F80 Service Manual ▷ View online
2-1
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
Ver 1.1 2006.12
2-2
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
2-1.
DISASSEMBLY
2-1-1. FOCUS CONNECT RING, OUTER BARREL ASSY AND MOUNT BLOCK
EXPLODED VIEW
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
Note: Attach the focus connect ring, outer barrel assy, gear block, mount block,
and filter tentatively when adjusting the flange back.
and filter tentatively when adjusting the flange back.
INNER GEAR POSITION
ADJUSTMENT
ADJUSTMENT
2 Signal PC Board
3 Ground (SP)
7 Gear Block
1 Filter
B
B
C
D
C
D
A
A
8 Inner Gear
9 Focus
Connect Ring
Connect Ring
Focus Hold
Button
Button
6 Outer Barrel Assy
Distance Scale
Plate
Plate
Main Flexible Unit
4 Rear Light
Shield Barrel
Shield Barrel
5 Mount Block
Mount Index
HELP01
HELP03
HELP05
HELP04
HELP06
HELP02
HELP08
HELP08
HELP09
HELP07
2-3
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
2-1-2. HELICOID UNIT
6 G6 Lens
4 G1 Lens Holder
5 G2+G4+G5 Assy
3 G1+G3+G7 Assy
G2 Lens Holder
G2 Stopper
EXPLODED VIEW
OPTICAL AXIS
CHECK/ADJUSTMENT
CHECK/ADJUSTMENT
Note: Always perform the optical axis check/adjustment when the
lens is removed.
lens is removed.
OPTICAL AXIS
CHECK/ADJUSTMENT
CHECK/ADJUSTMENT
HELP13
HELP11
HELP10
HELP12
HELP14
1 Focus Rubber Ring
2 G1 Adjustment
Screw
Screw
G1 Stopper
HELP
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
HELP
Note for assembling and grease applying positions are shown.
HELP01
Adhesive bond (B-40): J-6082-614-A
1.
Attach the rear light shield barrel. Apply the adhesive bond (B-40) to the three screws, and then fix the rear light shield barrel with
these screws as shown in the figure.
2.
Attach the ground spring to the rear light shield barrel.
3.
Attach the signal PC board, and fix it with the two screws as shown in the figure.
Note:
Be careful not to tighten the two screws too much.
Apply the Adhesive Bond
(B-40) (Three areas)
(B-40) (Three areas)
Signal PC Board
Screws
Ground spring
Rear Light Shield Barrel
Click on the first or last page to see other SAL500F80 service manuals if exist.