Sony SAL500F80 Service Manual ▷ View online
1-3
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
1-5.
TROUBLESHOOTING
1-5-1. Focus Trouble
OK
NG
OK
OK
OK
OK
NG
NG
NG
NG
NG
OK
Check the operation
again.
Replace the defective part
or apply the grease.
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the operation
of the gear block.
Check the operation
of the inner gear.
END
Check the attaching
condition of the distance
scale plate.
Adjust the affix position of
the distance scale plate.
Check the position
of the inner gear.
Adjust the position
of the inner gear.
Perform the optical
axis check/adjustment
and flange back (f’F)
adjustment.
(See pages 4-12
and 4-17.)
2-1
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
Ver 1.1 2006.12
2-2
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
2-1.
DISASSEMBLY
2-1-1. FOCUS CONNECT RING, OUTER BARREL ASSY AND MOUNT BLOCK
EXPLODED VIEW
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
Note: Attach the focus connect ring, outer barrel assy, gear block, mount block,
and filter tentatively when adjusting the flange back.
and filter tentatively when adjusting the flange back.
INNER GEAR POSITION
ADJUSTMENT
ADJUSTMENT
2 Signal PC Board
3 Ground (SP)
7 Gear Block
1 Filter
B
B
C
D
C
D
A
A
8 Inner Gear
9 Focus
Connect Ring
Connect Ring
Focus Hold
Button
Button
6 Outer Barrel Assy
Distance Scale
Plate
Plate
Main Flexible Unit
4 Rear Light
Shield Barrel
Shield Barrel
5 Mount Block
Mount Index
HELP01
HELP03
HELP05
HELP04
HELP06
HELP02
HELP08
HELP08
HELP09
HELP07
2-3
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
2-1-2. HELICOID UNIT
6 G6 Lens
4 G1 Lens Holder
5 G2+G4+G5 Assy
3 G1+G3+G7 Assy
G2 Lens Holder
G2 Stopper
EXPLODED VIEW
OPTICAL AXIS
CHECK/ADJUSTMENT
CHECK/ADJUSTMENT
Note: Always perform the optical axis check/adjustment when the
lens is removed.
lens is removed.
OPTICAL AXIS
CHECK/ADJUSTMENT
CHECK/ADJUSTMENT
HELP13
HELP11
HELP10
HELP12
HELP14
1 Focus Rubber Ring
2 G1 Adjustment
Screw
Screw
G1 Stopper
Click on the first or last page to see other SAL500F80 service manuals if exist.