Sony SAL500F80 Service Manual ▷ View online
HELP
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
HELP07
Adhesive bond (B-40): J-6082-614-A
Grease (G-10):
J-6082-618-A
1.
Apply the grease (G-10) to the gear on the gear block and gear portion of the gear (B) as shown in the figure.
2.
Apply the grease (G-10) to the two instruction portions of the gear shaft as shown in the figure, and attach it to the gear block.
3.
Attach the gear block. Apply the adhesive bond (B-40) to the two screws, and then fix the gear block with these screws as shown in
the figure.
Note:
Rotate the helicoid unit by about 1/2 turn to protrude.
Gear Block
Gear (B)
Gear Shaft
Apply Grease (G-10) (Gear)
Apply Grease (G-10) (Gear)
Apply Grease (G-10) (Two areas)
Apply Adhesive Bond (B-40) (Two areas)
HELP
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
HELP08
Adhesive bond (B-40):
J-6082-614-A
Grease (G-10):
J-6082-618-A
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the adhesive bond (B-40) to the tip of focus stopper pin and attach the stopper pin as shown in the figure.
2.
Apply the grease (G-10) and anti-diffusion agent (A-20) to the indicated portions of inner gear.
3.
Install the gear. Then, perform the “4-2-2. Optical Axis Adjustment”, “4-3. Flange back (f’F) Adjustment” and “4-4. Inner Gear
Position Adjustment” in order.
Apply the Grease (G-10)
(Gear)
(Gear)
Apply the Grease (G-10) (All circumference)
Apply the Anti-Diffusion Agent (A-20) (All circumference)
Apply the Grease (G-10)
(Sliding portion)
(Sliding portion)
Apply the Adhesive Bond (B-40)
Focus Stopper Pin
HELP
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
HELP09
Anti-diffusion agent (A-20): J-6082-611-A
Grease (G-10):
J-6082-618-A
Apply the anti-diffusion agent (A-20) and the grease (G-10) to the instruction portions of the focus connect ring as shown in the figure.
HELP10
Adhesive bond (B-10): J-6082-612-A
1.
Install the G1+G3+G7 assy to the helicoid unit, and fix it with the three G1 hold pin and G1 adjustment screws.
Note:
Stop the tightening of the G1 adjustment screw when the tip of the G1 adjustment screw comes in contact with the
G1+G3+G7 assy.
2.
After attaching the mount block tentatively.
3.
Perform the “4-2. Optical Axis Check/Adjustment”, apply the adhesive bond (B-10) to the three G1 adjustment screws.
Apply the Anti-Diffusion Agent
(A-20) (All circumferences)
(A-20) (All circumferences)
Apply the Grease (G-10) (U groove portion, two areas)
Helicoid Unit
G1 Adjustment Screw
(Three areas)
(Three areas)
G1 Hold Pin
(Three areas)
(Three areas)
Apply the Adhesive Bond (B-10)
Mount Block
Apply the Adhesive Bond (B-10)
Apply the Adhesive Bond (B-10)
HELP
SAL500F80 (REFLEX 8/500) (500mm F8 Reflex)
HELP11
Adhesive bond (B-40): J-6082-614-A
1.
Select the focus ring linkage pin of a proper diameter against the groove of the focus connect ring from the following table.
2.
Apply the adhesive bond (B-40) to the screw portion of the two focus ring linkage pins, and tighten them to the G1 lens holder.
Distance tube joint pin
Part No.
Description
2-689-211-01
Focus Ring Linkage Pin A (ø4.00)
2-689-212-01
Focus Ring Linkage Pin B (ø4.01)
2-689-213-01
Focus Ring Linkage Pin C (ø4.02)
Focus Ring Linkage Pin
Groove
Focus Joint Tube
Apply the Adhesive Bond (B-40)
Apply the Adhesive Bond (B-40)
Focus Ring Linkage Pin
G1 Lens Holder
Click on the first or last page to see other SAL500F80 service manuals if exist.