Sony SAL35F14G Service Manual ▷ View online
1-4
SAL35F14G (1.4/35G) (35mm F1.4G)
1-5-2. Focus Trouble
Check the operation
again.
Replace the defective part
or apply the grease.
OK
NG
OK
OK
OK
OK
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the coupler.
Check the fixed holding
tube and distance
control tube.
NG
NG
NG
NG
NG
END
OK
Check the installation of
the main flexible block.
Reinstall the main
flexible block.
Check pattern
of the main flexible block.
Clean the pattern of the
main flexible block.
Replace the
main flexible block.
Check the foecusing
operation again.
2-1
SAL35F14G (1.4/35G) (35mm F1.4G)
2. DISASSEMBLY
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
When top of tip does not reach holes or notches because the fixed
screw becomes obstructive, replace the fixed screw to below.
+B 3X5 7-682-546-09
screw becomes obstructive, replace the fixed screw to below.
+B 3X5 7-682-546-09
Ver 1.2 2007.05
2-2
SAL35F14G (1.4/35G) (35mm F1.4G)
2-1.
DISASSEMBLY
2-1-1. DECORATION RING AND MIRROR BARREL TUBE BLOCK
1.4/35G
A
A
EXPLODED VIEW
5
1 Group Lens Block
HELP01
3
G1
HELP02
HELP03
1
Ornamental Ring Label
2
Decoration Ring
4
Mirror Barrel
Tube Block
(See Page 2-3.)
(See Page 2-7.)
2-3
SAL35F14G (1.4/35G) (35mm F1.4G)
2-1-2. LENS MOUNT RIVETING BLOCK AND REAR LIGHT SHIELD BARREL
SONY
C
E
D
D
A
F
A
B
B
C
F
E
EXPLODED VIEW
HELP05
HELP06
HELP04
HELP04
HELP07
HELP08
HELP09
1
Rear Light Shield
Barrel
Preset Ring
Preset Ring
Holding Plate
Holding Plate
Main Spring
2
Connection Box
3
Lens Mount
Riveting Block
4
Back Adjustment
Washer
!-
Cinnabar Ring and
Fixed Barrel Block
7
Hold Sheet
!=
Focus Scale
Plate
![
Cam Ring
Support Plate
6
Coupler and
Coupler
Adjustment
Washer
Adjustment
Washer
5
Ground Spring
!/
Connector of
DV-FH Flexible
9
Focus Brush
8
Brush Hole
Cover
FLANGE BACK (f’F)
ADJUSTMENT
ADJUSTMENT
FOCUS BRUSH
POSITION
ADJUSTMENT
POSITION
ADJUSTMENT
(See Page 2-6.)
(See Page 2-4.)
Click on the first or last page to see other SAL35F14G service manuals if exist.