Sony SAL300F28G Service Manual ▷ View online
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP30
1.
Affix three sheets of MF ring rotation tape to three-divided circumferences of MF ring detecting encoder.
Note 1:
Affix the MF ring rotation tape not to protrude the MF ring detecting encoder.
Note 2:
When affixing, face the pattern side of MF ring detecting encoder to the front side.
Note 3:
Be careful not to damage the pattern.
2.
Affix firmly so that the adhesive side of MF ring detecting encoder is affixed to the focus ring.
MF Ring Detecting Encoder
Front side
Pattern side
MF Ring
Rotation Tape
Rotation Tape
MF Ring
Rotation Tape
Rotation Tape
Focus Ring
MF Ring Detecting
Encoder
Encoder
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP31
Adhesive bond (B-10):
J-6082-612-A
Adhesive bond (B-40):
J-6082-614-A
1.
Install the MF detection switch block to the outer tube. Apply two drops of adhesive bond (B-40) to the tips of two screws and tighten
the MF detection switch block with two screws.
2.
Install the MR sensor base plate block to the outer tube and tighten two screws tentatively.
3.
After performing the MR waveform inspection of [5-8. HALF COMPLETION INSPECTION], apply the adhesive bond (B-10) to the
heads of two screws.
Apply the adhesive bond (B-10)
Apply the adhesive
bond (B-40)
bond (B-40)
MR Sensor Base Plate Block
After finishing the
MR waveform inspection
MR waveform inspection
MR Sensor Base Plate Block
MF Detection
Switch Block
Switch Block
Outer
Tube
Tube
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
4.
Solder two harnesses (green/black) to the DV encoder flexible.
5.
Cut two sheets of polyester tape in 20mm length and affix them to cover the area 12x20mm so that four harnesses are fixed as shown
in the figure.
6.
Solder the MR connection flexible of MR sensor base plate block to the DV encoder flexible.
7.
Cut two sheets of polyester tape in20mm length and affix them to cover the area 12x20mm so that the MR sensor base plate block is
fixed.
DV Encoder
Flexible
Flexible
DV Encoder Flexible
MR connect flexible
Polyester Tape
(9X20mm)
(9X20mm)
Polyester Tape
(9X20mm)
(9X20mm)
20mm
20mm
12mm
12mm
MR Sensor Base Plate
Block
Block
Solder
MR connect flexible
Harness (Black)
Harness (Green)
(Leading from MF Detection
Switch Block)
Switch Block)
(From the FH Flexible)
Harness (Grey)
Harness (Orange)
HELP
SAL300F28G (2.8/300 G) (300mm F2.8 G)
HELP32
Adhesive bond (B-10):
J-6082-612-A
1.
Install the A encoder brush to the focus connect ring A with two screws tentatively.
2.
After performing the [5-6. Focus Brush Position Adjustment], apply the adhesive bond (B-10) to the indicated portions.
HELP33
Adhesive bond (B-40): J-6082-614-A
Adhesive bond (LOCTITE 460)
Note:
Use the adhesive bond (LOCTITE 460) or the equivalent.
Do not use the instant glue which becomes white after dried.
1.
Affix the focus connection ring tape to the focus cam ring as shown in the figure below.
2.
Make two pairs of focus connect ring pin and focus insulate bush and apply two drops of adhesive bond (B-40) to the tips of focus
connect ring pins. Fix the focus connect ring A to the focus cam ring tentatively to the extent that the gap exists.
3.
Fill the adhesive bond (LOCTITE 460) in the gap between focus cam ring and focus connect ring A.
4.
Tighten firmly two focus connect ring pins.
Apply the adhesive bond (B-10)
A Encoder Brush
Focus Connection
Ring A
Ring A
Focus Cam Ring
Affix the focus connection ring tape,
aligning the hole of focus connection
ring tape with the hole of focus cam ring.
aligning the hole of focus connection
ring tape with the hole of focus cam ring.
Focus Cam Ring
Focus Conection Ring Tape
Focus Conection Ring Tape
Tighten the focus connect ring pin tentatively
and fill the adhesive bond (LOCTITE 460)
in the gap.
and fill the adhesive bond (LOCTITE 460)
in the gap.
Focus Conection
Ring Tape
Ring Tape
Focus Connect
Ring A
Ring A
Focus Connect
Ring A
Ring A
Focus Connect Ring
Pin
Pin
Focus Connect Ring
Pin
Pin
Focus Insulate Bush
Focus Insulate Bush
Holes
Apply the adhesive bond (B-40)
Click on the first or last page to see other SAL300F28G service manuals if exist.