Sony SAL300F28G (serv.man4) Service Manual ▷ View online
SERVICE MANUAL
SAL300F28G (2.8/300 G) (300mm F2.8 G)
Ver. 1.4 2010.03
Sony EMCS Co.
2010C0800-1
© 2010.03
Published by Tokai TEC
US Model
Canadian Model
AEP Model
Chinese Model
Japanese Model
SUPPLEMENT-2
File this supplement with the service manual.
(09-497)
• Regarding half completion
inspection equipment modification
9-852-144-82
SAL300F28G
(2.8/300 G) (300mm F2.8 G)
This supplement-2 is the method for making the half completion inspection of SAL300F28G possible by
modifying the SSM HALF COMPLETION JIG: J-6082-662-A that is used for SAL2470Z and SAL1635Z.
modifying the SSM HALF COMPLETION JIG: J-6082-662-A that is used for SAL2470Z and SAL1635Z.
This SUPPLEMENT-2 is the revised version
of SUPPLEMENT-1.
Replace the SUPPLEMENT-1 (9-852-144-81)
with the SUPPLEMENT-2.
of SUPPLEMENT-1.
Replace the SUPPLEMENT-1 (9-852-144-81)
with the SUPPLEMENT-2.
— 2 —
SAL300F28G (2.8/300 G) (300mm F2.8 G)
English
[Modification method]
Note:
When using SSM HALF COMPLETION JIG as for SAL2470Z or SAL1635Z, the three lead wires below are not used, therefore
insulate the tip of these lead wires.
1. Remove the top cover of SSM HALF COMPLETION JIG by removing four screws.
2. Connect the three lead wires to 6(GND), 7, 8Pin of USB-1208LS.
3. Organize the lead wires as shown below, and pull those out through the gap in the Encoder connector.
4. Mount the top cover of SSM HALF COMPLETION JIG by tightening up four screws.
Loose
Tighten
— 3 —
SAL300F28G (2.8/300 G) (300mm F2.8 G)
[Connection method in the half completion inspection]
Note:
The modification of SSM HALF COMPLETION JIG (J-6082-662-A) should be completed.
1. Do the trial checking lens assembly as shown Fig.1.
(Outer Barrel and Focus Ring should be removed)
2. Solder the lead wires of the modified HALF COMPLETION JIG to the MM board unit of a checking lens and to the DC-DC board unit
as shown Fig.2.
3. Connect equipment and checking lens as shown Fig.3.
HALF COMPLETION JIG
Lens
FINISHED INSPECTION JIG
DC-DC board unit
MM board unit
Lead wire of the modifed one
— 4 —
SAL300F28G (2.8/300 G) (300mm F2.8 G)
[How to select ActuatorChecker with HALF COMPLETION JIG in half completion inspection]
Note 1:
The connection in the half completion inspection should be completed.
Note 2:
The lens adjustment program (ActuatorChecker) Ver3.08 or later is needed.
1. Start up "ActuatorChecker"
2. Click the Set up button.
3. When "Half" of SAL300F28G is selected, the AD TYPE appears.
4. Select Type I or II (It is changed by click) with reference to the below.
Description for AD TYPE
AD TYPE: I
Select if using the HALF COMPLETION JIG (J-6082-692-A)
AD TYPE: II
Select if using the modified SSM HALF COMPLETION JIG (J-6082-662-A)
5. Click the OK button.
*
It appears after selecting the AD TYPE: I
(HALF COMPLETION JIG (J-6082-692-A))
*
It appears after selecting the AD TYPE: II
(SSM HALF COMPLETION JIG (J-6082-
662-A))
