Sony SAL18552 Service Manual ▷ View online
2-6
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP10
1. Set the zoom to the TELE end and insert the 2nd lens barrel block, aligning the grooves with the projections at three locations.
Note:
Align the aperture lever with the ZF flexible PWB.
2. Set the zoom to the WIDE end, and the 2nd lens barrel block is pulled in and fixed.
Note:
If the zoom is set to the TELE end, the 2nd lens barrel block will be dislocated. Therefore, do not set the zoom to the TELE end.
2nd Lens Barrel Block
ZF Flexible PWB
Aperture Lever
Set to the WIDE end.
Set to the TELE end.
Projection
Projection
Projection
The 2nd Lens Barrel Block
is pulled in and fixed.
is pulled in and fixed.
Grooves
3. Install the tele stopper.
Note:
Install it in the state that the zoom is set to a position other than the TELE end.
4. Push the zoom to the TELE end and tighten it with one screw.
Tele Stopper
Tele Stopper
Push to the TELE end
HELP11
How to remove the zoom interlocking key
1. Set the zoom to the WIDE end and the focus to the near end. (In the state that the zoom interlocking key and the focus stopper
locate in the center.)
2. Remove two screws.
Zoom Interlocking Key
Focus Stopper
Set to the WIDE end.
Set the unit to the near end.
3. Unlock the engagement of the bayonet by moving right and left the zoom barrel assy and shift it in the front lens barrel direction.
4. Remove the zoom interlocking key.
4. Remove the zoom interlocking key.
Zoom Interlocking Key
Bayonet
2-7
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP12
How to install the zoom interlocking key
1. Set the zoom to the WIDE end.
Note:
If the zoom is set to the TELE end, the front lens barrel will be dislocated. Therefore, never set the zoom to the TELE end.
2. Set the focus to the near end by rotating.
Set the unit to the near end.
Move the hole of Zoom Cam Sleeve in
the arrow direction. (Set to the WIDE end.)
the arrow direction. (Set to the WIDE end.)
3. Unlock the engagement of the bayonet by moving right and left the zoom barrel assy and shift it in the front lens barrel direction.
4. Insert the zoom interlocking key in the hole of zoom cam sleeve and hold it.
4. Insert the zoom interlocking key in the hole of zoom cam sleeve and hold it.
Front Lens Barrel
Bayonet
Zoom Interlocking Key
Remove the bayonet and shift the zoom barrel assy
in the front lens barrel direction.
in the front lens barrel direction.
Hole of Zoom Cam Sleeve
5. Return the zoom barrel assy and engage the bayonet with it.
6. Align the zoom barrel assy with the hole of zoom interlocking key and tighten them with two screws.
6. Align the zoom barrel assy with the hole of zoom interlocking key and tighten them with two screws.
Zoom Interlocking Key
Bayonet
Return the zoom barrel assy
and engage the bayonet with it.
and engage the bayonet with it.
HELP13
1. Aligning the pin of fixed sleeve with the pin hole of fixed hold ring, install the fixed hold ring block.
Note:
Insert the projections of front lens barrel in the grooves of focus drive ring.
Focus Drive Ring
Front Lens Barrel
Fixed Hold Ring
Fixed Sleeve
Fixed Hold Ring Block
Pin
Groove
Groove
Groove
Projection
Projection
Projection
Pin hole
2. Fix it with three screws.
2-8
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP14
Grease (FT-210): 9-913-200-37
1. Apply the grease (FT-210) to the indicated portion of zoom barrel assy.
Apply the grease
(FT-210)
(FT-210)
Be careful not to apply
the grease to this area.
the grease to this area.
Zoom Barrel Assy
HELP15
1. Align the cut portion of zoom barrel assy with the cut portions of zoom sheet.
2. Aligning the projections of front lens barrel with the cut portions of zoom barrel assy, insert the zoom barrel assy in the front lens
2. Aligning the projections of front lens barrel with the cut portions of zoom barrel assy, insert the zoom barrel assy in the front lens
barrel block.
Zoom Barrel Assy
Zoom Sheet
Front Lens Barrel Block
Front Lens Barrel
Projection
Projection
Projection
Cut Portions
HELP16
Grease (SG-310): 9-913-200-36
1. Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Note:
Apply the grease so that the groove of helicoid is filled with grease.
2. Apply the grease (SG-310) to the indicated portions of front lens barrel. (Three locations)
Front Lens Barrel
Apply the grease (SG-310)
Apply the grease (SG-310)
Apply the grease (SG-310)
(Fill the groove of helicoid with the grease)
(Fill the groove of helicoid with the grease)
Apply the grease (SG-310)
(Fill the groove of helicoid with the grease)
(Fill the groove of helicoid with the grease)
HELP17
1. Mount the GP1 moving barrel on the front lens barrel.
2. Rotate counterclockwise (viewing from the mount side) the GP1 moving barrel and assemble it by rotating it clockwise at the position
2. Rotate counterclockwise (viewing from the mount side) the GP1 moving barrel and assemble it by rotating it clockwise at the position
where the helicoid is engaged (clicked).
Note:
Note:
When moving the helicoid to the last, confirm that the bayonet click portion comes to the location where the screw hole
locates about 90 de-
grees apart from the pin of fixed sleeve in the clockwise direction (viewing from the mount side).
GP1 Moving Barrel
Front Lens
Barrel
Barrel
Fixed
Sleeve
Sleeve
Front Lens Barrel
GP1 Moving
Barrel
Barrel
Helicoid
Pin
Meet the helicoids each other by rotating
counterclockwise the GP1 Moving Barrel
counterclockwise the GP1 Moving Barrel
When the helicoid engages (clicks),
assemble the GP1 Moving Barrel
by rotating it clockwise.
assemble the GP1 Moving Barrel
by rotating it clockwise.
Screw hole at the location where it is
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
clockwise (viewing from the mount)
turned by about 90 degrees from the pin
Bayonet click portion
2-9
SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)
HELP18
Grease (FT-210): 9-913-200-37
Grease (SG-310): 9-913-200-36
Grease (SG-310): 9-913-200-36
1. Apply the grease (SG-310) to the grooves of fixed sleeve. (Three locations)
Note:
Apply the grease so that the groove is filled with grease.
2. Apply the grease (FT-210) to the wall of oblong hole of fixed sleeve. (Six locations)
Fixed Sleeve
Apply the grease (SG-310)
to the grooves (Three locations)
(Groove is filled)
to the grooves (Three locations)
(Groove is filled)
Apply the grease (FT-210)
to the wall of oblong hole
(Six locations)
to the wall of oblong hole
(Six locations)
3. Apply the grease (SG-310) to the indicated portions of GP1 moving barrel. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
GP1 Moving Barrel
Apply the grease (SG-310)
(Six locations)
(Six locations)
4. Apply the grease (SG-310) to the helicoids of zoom cam sleeve. (Six locations)
Note:
Apply the grease so that the grease remains on the wall.
Apply the grease (SG-310)
(Three locations)
(Three locations)
Zoom Cam Sleeve
Apply the grease (SG-310)
(Three locations)
(Three locations)
HELP19
1. Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel and drop the fixed sleeve in GP1 moving barrel.
2. While holding the fixed sleeve and the GP1 moving barrel, install the zoom cam sleeve, aligning the projections of zoom cam sleeve
2. While holding the fixed sleeve and the GP1 moving barrel, install the zoom cam sleeve, aligning the projections of zoom cam sleeve
with the cut portions B of fixed sleeve.
Fixed Sleeve
GP1 Moving Barrel
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving Barrel
Cut Portion A
Cut Portion B
Cut Portion B
Cut Portion B
Projection
Projection
3. Align the cut portions A of fixed sleeve with the projections of GP1 moving barrel again and assemble the zoom cam sleeve by rotating
it counterclockwise (viewing from the mount side).
Fixed Sleeve
Zoom Cam Sleeve
Fixed Sleeve
GP1 Moving
Barrel
Barrel
Cut Portion A
Projection
Rotate counterclockwise
the Zoom Cam Sleeve
(Viewing from the mount side)
the Zoom Cam Sleeve
(Viewing from the mount side)
Click on the first or last page to see other SAL18552 service manuals if exist.