DOWNLOAD Sony SAL18552 Service Manual ↓ Size: 8.12 MB | Pages: 55 in PDF or view online for FREE

2-4

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  While inserting the aperture interlocking fork in the aperture lever, install the mount block.

 

Mount Block

Aperture Interlocking Fork

Aperture Lever

2.  Select 1 to 2 pieces of back adjustment washers to make a combination of specified thickness.

  The amount of back adjustment washers differs depending on the adjustment. (Refer to the flange back adjustment.)

3.  Push the back adjustment washers in between the boss and the mount block. (3 locations)

  When stacking several pieces of back adjustment washers, install the washers so that thin one comes at the outer side.

4.  Tighten the mount block with three screws.
5.  Connect the ZF flexible PWB to the connector of the CL-022 mount block assy.

 

Back Adjustment Washers

Mount  Block

ZF Flexible PWB

Back Adjustment Washers

Back Adjustment 
Washers

Connector of 
CL-022 Mount
Block Assy

Boss

Thin

Thick

1.  Set the zoom to somewhere in the range of  28-35  and the focus to the infinity end.
2.  Aligning the character [3.5] on the front decoration plate with the slant portion of bayonet, affix the front decoration plate.

  Align with the slant portion of bayonet at the tele Stopper side.

 

Front Decoration Plate

Tele Stopper

Slant portion of bayonet

1.  Affix the flexible of DC motor (geared) to the fixed holding tube.
2.  Connect the ZF flexible PWB to the connector.

 

ZF Flexible PWB

Connector

Affix the flexible of 
DC Motor (Geared) to 
the Fixed Holding Tube.

2-5

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

Adhesive bond (B-10): J-6082-612-A

1.  Cut the tip of focus brush with nippers.
2.  Install the focus brush and fix it with one screw.

  Install it in the state that the focus stopper and the zoom interlocking key locate in the center.

3.  After performing the focus brush position adjustment, apply the adhesive bond (B-10) to the head of screw.

 

Focus Brush

Focus Stopper

Zoom Interlocking Key

Apply the adhesive bond (B-10)

Focus Brush

Cut with nippers.

Adhesive bond (B-10): J-6082-612-A

1.  Cut the tip of zoom brush with nippers.
2.  Install the zoom brush and fix it with one screw.

  Install it in the state that the focus stopper and the zoom interlocking key locate in the center.

3.  After performing the zoom brush position adjustment, apply the adhesive bond (B-10) to the head of screw.

 

Zoom Interlocking Key

Focus Stopper

Zoom Brush

Zoom Brush

Apply the adhesive 
bond (B-10)

Cut with nippers.

1.  Install the 1st lens barrel block.

  Align the index hole with the focus stopper.

2.  Turn counterclockwise the 1st lens barrel block and fix it with one screw.

 

1st Lens Barrel Block

Focus Stopper

1st Lens Barrel Block

Index hole

2-6

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  Set the zoom to the TELE end and insert the 2nd lens barrel block, aligning the grooves with the projections at three locations.

  Align the aperture lever with the ZF flexible PWB.

2.  Set the zoom to the WIDE end, and the 2nd lens barrel block is pulled in and fixed.

  If the zoom is set to the TELE end, the 2nd lens barrel block will be dislocated. Therefore, do not set the zoom to the TELE end.

 

2nd Lens Barrel Block

ZF Flexible PWB

Aperture Lever

Set to the WIDE end.

Set to the TELE end.

Projection

Projection

Projection

The 2nd Lens Barrel Block 
is pulled in and fixed.

Grooves

3.  Install the tele stopper.

  Install it in the state that the zoom is set to a position other than the TELE end.

4.  Push the zoom to the TELE end and tighten it with one screw.

 

Tele Stopper

Tele Stopper

Push to the TELE end

1.  Set the zoom to the WIDE end and the focus to the near end. (In the state that the zoom interlocking key and the focus stopper 

locate in the center.)

2.  Remove two screws.

 

Zoom Interlocking Key

Focus Stopper

Set to the WIDE end.

Set the unit to the near end.

3.  Unlock the engagement of the bayonet by moving right and left the zoom barrel assy and shift it in the front lens barrel direction.
4.  Remove the zoom interlocking key.

 

Zoom Interlocking Key

Bayonet

2-7

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  Set the zoom to the WIDE end.

  If the zoom is set to the TELE end, the front lens barrel will be dislocated. Therefore, never set the zoom to the TELE end.

2.  Set the focus to the near end by rotating. 

 

Set the unit to the near end.

Move the hole of Zoom Cam Sleeve in 
the arrow direction. (Set to the WIDE end.)

3.  Unlock the engagement of the bayonet by moving right and left the zoom barrel assy and shift it in the front lens barrel direction.
4.  Insert the zoom interlocking key in the hole of zoom cam sleeve and hold it.

 

Front Lens Barrel

Bayonet

Zoom Interlocking Key

Remove the bayonet and shift the zoom barrel assy
in the front lens barrel direction.

Hole of Zoom Cam Sleeve

5.  Return the zoom barrel assy and engage the bayonet with it.
6.  Align the zoom barrel assy with the hole of zoom interlocking key and tighten them with two screws.

 

Zoom Interlocking Key

Bayonet

Return the zoom barrel assy 
and engage the bayonet with it.

1.  Aligning the pin of fixed sleeve with the pin hole of fixed hold ring, install the fixed hold ring block.

  Insert the projections of front lens barrel in the grooves of focus drive ring.

 

Focus Drive Ring

Front Lens Barrel

Fixed Hold Ring

Fixed Sleeve

Fixed Hold Ring Block

Pin

Groove

Groove

Groove

Projection

Projection

Projection

Pin hole

2.  Fix it with three screws.