DOWNLOAD Sony SAL18552 Service Manual ↓ Size: 8.12 MB | Pages: 55 in PDF or view online for FREE

2-3

Note for assembling and grease applying positions are shown.

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  Remove three screws fixing the rear barrel assy.
2.  Set the AF/MF switch to AF.
3.  Push the rear barrel assy to the mount side.
4.  Remove the switch panel block by inserting a Philips screwdriver or a knife from the focus ring side.

 

Switch Panel Block

Push the rear barrel assy to the mount side 
and insert a philips screwdriver or a knife.

Philips screwdriver or knife.

1.  Set the knob of switch panel block to AF.
2.  Peel the released paper from the switch panel block and install the switch panel block.

 

Switch Panel Block

Knob

1.  Set the zoom to a position other than the TELE end and install the zoom key stopper.
2.  Push clockwise the zoom key stopper.

  When installing the rear barrel assy, insert the projection a of rear barrel assy in the groove of zoom key stopper.

 

Zoom Key Stopper

Rear Barrel Assy

Set the zoom to a position
other than the TELE end

Push clockwise

Projection A

Groove of the
Zoom Key Stopper

2-4

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  While inserting the aperture interlocking fork in the aperture lever, install the mount block.

 

Mount Block

Aperture Interlocking Fork

Aperture Lever

2.  Select 1 to 2 pieces of back adjustment washers to make a combination of specified thickness.

  The amount of back adjustment washers differs depending on the adjustment. (Refer to the flange back adjustment.)

3.  Push the back adjustment washers in between the boss and the mount block. (3 locations)

  When stacking several pieces of back adjustment washers, install the washers so that thin one comes at the outer side.

4.  Tighten the mount block with three screws.
5.  Connect the ZF flexible PWB to the connector of the CL-022 mount block assy.

 

Back Adjustment Washers

Mount  Block

ZF Flexible PWB

Back Adjustment Washers

Back Adjustment 
Washers

Connector of 
CL-022 Mount
Block Assy

Boss

Thin

Thick

1.  Set the zoom to somewhere in the range of  28-35  and the focus to the infinity end.
2.  Aligning the character [3.5] on the front decoration plate with the slant portion of bayonet, affix the front decoration plate.

  Align with the slant portion of bayonet at the tele Stopper side.

 

Front Decoration Plate

Tele Stopper

Slant portion of bayonet

1.  Affix the flexible of DC motor (geared) to the fixed holding tube.
2.  Connect the ZF flexible PWB to the connector.

 

ZF Flexible PWB

Connector

Affix the flexible of 
DC Motor (Geared) to 
the Fixed Holding Tube.

2-5

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

Adhesive bond (B-10): J-6082-612-A

1.  Cut the tip of focus brush with nippers.
2.  Install the focus brush and fix it with one screw.

  Install it in the state that the focus stopper and the zoom interlocking key locate in the center.

3.  After performing the focus brush position adjustment, apply the adhesive bond (B-10) to the head of screw.

 

Focus Brush

Focus Stopper

Zoom Interlocking Key

Apply the adhesive bond (B-10)

Focus Brush

Cut with nippers.

Adhesive bond (B-10): J-6082-612-A

1.  Cut the tip of zoom brush with nippers.
2.  Install the zoom brush and fix it with one screw.

  Install it in the state that the focus stopper and the zoom interlocking key locate in the center.

3.  After performing the zoom brush position adjustment, apply the adhesive bond (B-10) to the head of screw.

 

Zoom Interlocking Key

Focus Stopper

Zoom Brush

Zoom Brush

Apply the adhesive 
bond (B-10)

Cut with nippers.

1.  Install the 1st lens barrel block.

  Align the index hole with the focus stopper.

2.  Turn counterclockwise the 1st lens barrel block and fix it with one screw.

 

1st Lens Barrel Block

Focus Stopper

1st Lens Barrel Block

Index hole

2-6

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  Set the zoom to the TELE end and insert the 2nd lens barrel block, aligning the grooves with the projections at three locations.

  Align the aperture lever with the ZF flexible PWB.

2.  Set the zoom to the WIDE end, and the 2nd lens barrel block is pulled in and fixed.

  If the zoom is set to the TELE end, the 2nd lens barrel block will be dislocated. Therefore, do not set the zoom to the TELE end.

 

2nd Lens Barrel Block

ZF Flexible PWB

Aperture Lever

Set to the WIDE end.

Set to the TELE end.

Projection

Projection

Projection

The 2nd Lens Barrel Block 
is pulled in and fixed.

Grooves

3.  Install the tele stopper.

  Install it in the state that the zoom is set to a position other than the TELE end.

4.  Push the zoom to the TELE end and tighten it with one screw.

 

Tele Stopper

Tele Stopper

Push to the TELE end

1.  Set the zoom to the WIDE end and the focus to the near end. (In the state that the zoom interlocking key and the focus stopper 

locate in the center.)

2.  Remove two screws.

 

Zoom Interlocking Key

Focus Stopper

Set to the WIDE end.

Set the unit to the near end.

3.  Unlock the engagement of the bayonet by moving right and left the zoom barrel assy and shift it in the front lens barrel direction.
4.  Remove the zoom interlocking key.

 

Zoom Interlocking Key

Bayonet