DOWNLOAD Sony SAL18552 Service Manual ↓ Size: 8.12 MB | Pages: 55 in PDF or view online for FREE

2-1

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

•  Make sure that the flat cable and flexible board are not cracked of bent at the terminal.

Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, don t pull at wire of connector. It is possible that a wire is snapped.

•  When installing a connector, don t press down at wire of connector. 

It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

Notches

Holes

Universal wrench
J-6082-609-A

Chip-A for
universal wrench:
J-6082-609-1

Chip-B for
universal wrench:
J-6082-609-2

Chip-C for
universal wrench:
J-6082-609-3

Attach the chip-A, chip-B or chip-C to the universal wrench.
For the notches:
For the holes:

In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.

chip-A, chip-C
chip-B

Notches

Holes

Chip

Chip-A

or

Chip-C

Chip-A

or

Chip-C

Chip-B

Chip-B

Chip

Match the universal wrench to the holes or notches of the lens block, etc.

Match the universal wrench
to the width of holes or notches.

Universal wrench

B-10

FT-210

Grease (FT-210):              9-913-200-37

Adhesive bond (B-10):           J-6082-612-A

SG-310

Grease (SG-310):              9-913-200-36

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

2-2

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

6

5

qd

1

q;

9

8

3

2

7

1

2

5

qs

qa

6

6

4

6

q;

3

9

8

7

6

4

B-10

B-10

SG-310

SG-310

FT-210

FT-210

SG-310

FT-210

Focus Stopper

2-1-1

2-1-2

Fixed Sleeve

Zoom Interlocking Key

GP1 Moving Barrel

Zoom Brush

Focus Drive Ring

Mount Block

CL-022 Mount
Block Assy

Name Plate

Rear Barrel Assy

Mount Cover

Focus Rubber Ring

Front Lens Barrel

Tele Stopper

Zoom Cam Sleeve

Back
Adjustment
 Washers

Friction Sheet 

Fixed Hold Ring

Focus Brush

Zoom Rubber Ring

Zoom Barrel Assy 

Zoom Sheet

ZF Flexible PWB

Front Ring

Front 
Decoration Plate

Zoom Key Stopper

DC Motor
(Geared)

Switch Panel Block

(Note 2)

Function Lever

Back Adjustment Washers

Back Adjustment
 Washers

1st Lens Barrel Block

2nd Lens Barrel Block

Screw

Note 1:
This lens can disassemble both the
1st lens side and the mount side. 

B-10

Install the focus rubber ring, 
orienting the concave 
step side to the eyepiece. 

Note 2: 
How to remove the switch panel block (Scratch prevention)
1. Remove three screws fixing the rear barrel assy.
2. Set the AF/MF switch to AF.
3. Push the rear barrel assy to the mount side.
4. Remove the switch panel block by inserting a Philips 
    screwdriver or a knife from the focus ring side.

2-3

Note for assembling and grease applying positions are shown.

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  Remove three screws fixing the rear barrel assy.
2.  Set the AF/MF switch to AF.
3.  Push the rear barrel assy to the mount side.
4.  Remove the switch panel block by inserting a Philips screwdriver or a knife from the focus ring side.

 

Switch Panel Block

Push the rear barrel assy to the mount side 
and insert a philips screwdriver or a knife.

Philips screwdriver or knife.

1.  Set the knob of switch panel block to AF.
2.  Peel the released paper from the switch panel block and install the switch panel block.

 

Switch Panel Block

Knob

1.  Set the zoom to a position other than the TELE end and install the zoom key stopper.
2.  Push clockwise the zoom key stopper.

  When installing the rear barrel assy, insert the projection a of rear barrel assy in the groove of zoom key stopper.

 

Zoom Key Stopper

Rear Barrel Assy

Set the zoom to a position
other than the TELE end

Push clockwise

Projection A

Groove of the
Zoom Key Stopper

2-4

SAL18552 (DT 3.5-5.6/18-55 SAM Ⅱ) (DT 18-55mm F3.5-5.6 SAM II)

1.  While inserting the aperture interlocking fork in the aperture lever, install the mount block.

 

Mount Block

Aperture Interlocking Fork

Aperture Lever

2.  Select 1 to 2 pieces of back adjustment washers to make a combination of specified thickness.

  The amount of back adjustment washers differs depending on the adjustment. (Refer to the flange back adjustment.)

3.  Push the back adjustment washers in between the boss and the mount block. (3 locations)

  When stacking several pieces of back adjustment washers, install the washers so that thin one comes at the outer side.

4.  Tighten the mount block with three screws.
5.  Connect the ZF flexible PWB to the connector of the CL-022 mount block assy.

 

Back Adjustment Washers

Mount  Block

ZF Flexible PWB

Back Adjustment Washers

Back Adjustment 
Washers

Connector of 
CL-022 Mount
Block Assy

Boss

Thin

Thick

1.  Set the zoom to somewhere in the range of  28-35  and the focus to the infinity end.
2.  Aligning the character [3.5] on the front decoration plate with the slant portion of bayonet, affix the front decoration plate.

  Align with the slant portion of bayonet at the tele Stopper side.

 

Front Decoration Plate

Tele Stopper

Slant portion of bayonet

1.  Affix the flexible of DC motor (geared) to the fixed holding tube.
2.  Connect the ZF flexible PWB to the connector.

 

ZF Flexible PWB

Connector

Affix the flexible of 
DC Motor (Geared) to 
the Fixed Holding Tube.