DOWNLOAD Sony SAL18135 Service Manual ↓ Size: 7.67 MB | Pages: 47 in PDF or view online for FREE

Model
SAL18135
Pages
47
Size
7.67 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
sal18135.pdf
Date

Sony SAL18135 Service Manual ▷ View online

2-2
SAL18135 (3.5-5.6/18-135 SAM) (DT18-135mm F3.5-5.6 SAM)
2-1. DISASSEMBLY
A
A
REPAIR PARTS LIST
REPAIR PARTS LIST
REPAIR PARTS LIST
3
2
9
1
2
3
2
1
4
5
1
4
5
3
9
8
8
4
5
6
6
7
8
FT-210
B-110
B-10
HELP01
HELP02
Note :
7
qa
q;
qs
HELP03
HELP04
HELP05
HELP06
HELP07
HELP08
HELP10
HELP09
Remove the BL contact box from
the rear light interception tube (8948).
Remove from the flexible board.
G-118
G-85
Focus Ring Assy
Encoder Plate
Friction Plate
Focus Interlock Ring (8948)
1st Outer Barrel Assy
PWB (ZM-AFM8948), 
LF-145 FLEX
Remove the 1st Lens Ring (8948) using
the Universal wrench (J-6082-609-A).
Focus Interlock Plate (8948)
This lens can be disassembled from both directions of 
1 group lens side and mount side. 
Remove and install 
with the aperture open.
MF Ring Tape
Sinnabar Ring
Back Washer
Flange Back (f'F)
Adjustment
Aperture Diameter
Adjustment
In the state that the unit is set to
the TELE end, remove it and install it.
Preset Ring (8948)
Rear Barrel Assy
CL-037 Mount Board Assy
Mount Assy
Mount Base Assy
Main Spring (8948)
Rear Cover Barrel (8948)
B/L Contact Box Assy
Zoom Brush Position
Adjustment
Brush (8948)
Center Barrel Assy
Zoom Ring Assy
Z Brush Plate (8948)
Zoom Sheet
Polyester Tape
(Black)10mm
Zoom Rubber Ring (8948)
Focus Rubber Ring (8948)
Holder Barrel Assy
AF Gear Box (8948)
Projective Resolving Power
(Partial Blur) Adjustment
1st Lens Assy
1st Lens Sheet (8948)
1st Lens Ring (8948)
Optical Assy
In the state that the unit is set to
the TELE end, remove it and install it.
In the state that the unit is set to
the TELE end, remove it and install it.
2-3
HELP
Note for assembling and grease applying positions are shown.
SAL18135 (3.5-5.6/18-135 SAM) (DT18-135mm F3.5-5.6 SAM)
HELP01
1.  Stick the 1st group sheet (8948) matching its printed characters with the index mark as shown in the figure.
Note:
  Be careful so that the deviation of sticking shall be within one character (right and left).
Index mark
1st Lens Sheet (8948)
1st Lens Sheet (8948)
Index mark
Deviation of
sticking shall
Deviation of
sticking shall
HELP02
Bond (B-110) : J-6082-617-A
1.  Insert the 1st group lens assy into the 1st group movement frame at the position where the hole in the 1st group lens assy shifts approx. 
20 degrees clockwise from the index mark.
2.  Turn the 1st group lens assy approx. 20 degrees counterclockwise to the position where the hole in the 1st group lens assy matches the 
index mark.
3.  Apply the bond (B-110) after  4-5-2. Focus Shift(Focal Distance)/Flange Back (f F) Adjustment  has been completed.
20
Index mark
Index mark
Index mark
1st Lens Assy
1st Lens Assy
Hole
Hole
Hole
Hole
1 st Moving Frame
Apply the bond
(B-110)
HELP03
1.  Open the aperture lever.
2.  Open the preset lever and maintain the position, and then install the mount assy block to the unit while inserting the preset lever into 
the aperture lever.
Mount Assy
Preset Lever
Aperture Lever
Preset Lever
HELP04
1.  Set the unit to the TELE end.
2.  While inserting the variable resistor lever into the encoder plate groove, install the rear retainer ring assy and secure it with 4 screws.
3.  Turn the focus control ring and the focus rubber ring (8948) to check whether the variable resistor lever is inserted into the encoder 
plate groove.
Focus Rubber Ring (8948)
Holder Barrel Assy
Groove of the Encoder Plate
Groove of
the Encoder Plate
Variable Resistor Lever
Variable Resistor Lever
2-4
SAL18135 (3.5-5.6/18-135 SAM) (DT18-135mm F3.5-5.6 SAM)
HELP05
1.  Attach the focus rubber ring (8948) so that its convex comes to the mount side.
Focus Rubber Ring (8948)
Convex
HELP06
Grease (FT-210): 9-913-200-37
1.  Apply grease (FT-210) to the gear part of the Focus Interlock Ring (8948).
2.  Install the focus joint ring assy to the unit while inserting the lever of the focus joint plate (8948) into the groove of the 2nd group 
movement frame.
Focus Interlock Plate Assy
Focus Interlock Ring (8948)
Apply the grease
(FT-210)
Groove of the 2 Group Moving Frame
Gear part
Lever of the Focus
Interlock Plate (8948)
HELP07
Bond (B-10) : J-6082-612-A
1.  Set the unit to the TELE end, install the brush (8948), and secure it with a screw.
Note:
  Set the brush (8948) at the position of the LF-145 flexible board ZM-AFM8948 (8948) pattern referring to the figure.
2. After 
performing 4-7-3. Zoom Pattern Inspection , apply the adhesive bond (B-10) to the head of screw.
PWB (ZM-AFM8948), 
LF-145 FLEX
PWB (ZM-AFM8948), 
LF-145 FLEX
Apply the bond
(B-10)
Brush (8948)
Brush (8948)
Z Brush Plate (8948)
HELP08
Grease (G-85): J-6082-626-A
Grease (G-118): J-6082-680-A
1.  Apply the grease (G-85) to the indicated portion of center barrel assy.
Note:
  Avoid applying the grease outside in the application-prohibited areas.
2.  Apply the grease (G-118) to the indicated portion of center barrel assy.
Center Barrel Assy
Center Barrel Assy
Apply the grease
(G-85)
Apply the grease
(G-85)
Apply the grease
(G-85)
Apply the grease
(G-118)
Application-prohibited areas
2-5
SAL18135 (3.5-5.6/18-135 SAM) (DT18-135mm F3.5-5.6 SAM)
HELP09
1.  Extend the 1st group movement frame to the position shown in the figure below.
2.  While passing the LF-145 flexible board ZM-AFM8948 (8948) through the hole in the middle barrel assy, install the middle barrel assy 
and the zoom ring assy to the unit.
3.  Set the zoom ring assy to a focal length of 35 mm and extend the 1st group outer barrel assy and the 1st group movement frame to the 
position shown in the figure below to align the zoom ring assy hole with the zoom pin screw hole.
4.  Tighten two zoom pins.
1st Outer Barrel Assy
Center Barrel Assy
Zoom Ring Assy
Zoom ring assy hole and
zoom pin screw hole
PWB (ZM-AFM8948), 
LF-145 FLEX
Hole
Zoom Ring Assy
1 st Moving Frame
Zoom Pin
Zoom Pin
1 st Moving Frame
HELP10
1.  Align the opening of the 1st group outer barrel assy with the opening of the 3rd movement barrel assy, and then install the 1st group 
outer barrel assy to the optical assy while inserting the two projections of the 1st group outer barrel assy into the two grooves of the re-
tainer ring.
2.  Tighten three screws.
1st Outer Barrel Assy
Stationary Barrel
Optical Assy
Projection
Grooves
Grooves
Opening
Opening
Page of 47
Display

Click on the first or last page to see other SAL18135 service manuals if exist.