Sony SAL16F28 Service Manual ▷ View online
HELP
SAL16F28 (2.8/16 FISH-EYE) (16mm F2.8 Fisheye)
HELP05
Adhesive bond (B-40): J-6082-614-A
Adhesive bond (B-60): J-6082-616-A
1.
Affix the rear light shield barrel to flexible set tape as shown in the figure.
2.
Affix the rear light shield barrel to main flexible unit as shown in the figure. (Based on the position of figure)
Note:
When handling the main flexible unit, take care static electricity.
3.
Apply the adhesive bind (B-60) to the instruction part as shown in the figure
Note:
Attach the tape (fixed auxiliary use) to the main flexible unit to the rear light shield barrel as illustrated, please wait until
stiffening at night.
4.
Apply the adhesive bond (B-40) to the tips of 3 screws shown in figure and tighten the screws.
5.
Attach the ground spring as shown in the figure.
6.
Attach the main flexible unit to the rear light shield barrel with with two screws as shown in the figure.
Rear Light Shield Barrel
Flexible Set Tape
Putting standard of unit
Apply the adhesive bond (B-60)
Tape (Fixed auxiliary use)
Apply the adhesive bond(B-40)
Apply the adhesive bond(B-40)
Ground Spring
Rear Light Shield Barrel
Lens Mount Riveting Block
Ver 1.2 2007.02
HELP
SAL16F28 (2.8/16 FISH-EYE) (16mm F2.8 Fisheye)
HELP06
Grease (G-85):
J-6082-626-A
Anti-diffusion agent (A-20): J-6082-611-A
1.
Apply the grease (G-85) to the portions (3 locations) indicated in figure.
2.
Apply the anti-diffusion agent (A-20) to all circumferences of portions indicated in figure.
Note:
After installation, confirm the movement.
HELP07
Oil (O-20): J-6082-610-A
Adhesive bond (LOCTITE 460) (Note)
Note:
Use adhesive bond (LOCTITE 460) or an equivalent article.
Don’t use what becomes white after drying like a quick-drying glue.
1.
Apply the adhesive bond (LOCTITE 460) to the tip of stopper screw and tighten the stopper screw.
2.
Apply the oil (O-20) to the all of main spring.
Apply the adhesive bond(LOCTITE 460)
Apply the oil(O-20)
Lens Mount Reveting Block
Lens A Mount
Stopper Screw
Preset Ring
Main Spring
Preset Ring Holding Plate
Apply the grease(G-85) to 3 locations on the back side
Apply the grease(G-85)
Apply the anti-diffusion agent(A-20)
(All circumferences)
(All circumferences)
Lens Mount Riveting Block
HELP
SAL16F28 (2.8/16 FISH-EYE) (16mm F2.8 Fisheye)
HELP08
Adhesive bond(B-40): J-6082-614-A
Grease (G-30):
J-6082-620-A
Grease (G-85):
J-6082-626-A
1.
Apply the grease (G-30, G-85) to the portions of coupler shown in figure.
2.
Apply the bond (B-40) to the tips of screws shown in figure.
HELP09
Anti-diffusion agent (A-20): J06082-611-A
Apply the anti-diffusion agent (A-20) to the portions (all circumferences of shaded portions) indicated in figure.
Inner Barrel
Apply the anti-diffusion agent(A-20)
(All circumferences)
(All circumferences)
Apply the grease(G-30)
Apply the grease(G-30)
Apply the adhesive bond(B-40)
Coupler
Gear Base Plate Rivet Block
Apply the grease(G-85)
Apply the grease(G-85)
HELP
SAL16F28 (2.8/16 FISH-EYE) (16mm F2.8 Fisheye)
HELP10
Grease (G-30):
J-6082-620-A
Anti-diffusion agent (A-20):
J06082-611-A
Universal wrench:
J-6082-609-A
Chip-A for Universal Wrench: J-6082-609-1
Chip-B for Universal Wrench: J-6082-609-2
1.
Apply the anti-diffusion agent (A-20) to the portions indicated in figure.
2.
Apply the grease (G-30) to the portions indicated in figure.
3.
Align the filter rotation linkage pin and the positioning pin that is attached to connection barrel, attach the filter change cam ring.
4.
Holding the filter change cam ring, release the filter link lever of instruction hole of vicinity in the arrow direction, set the filter
change cam tube.
5.
Align that the positioning pin of front lens barrel, “U groove” of vicinity of “NORMAL” on filter select ring and positioning pin of
connection barrel, then attach them.
6.
Use the universal wrench, tighten the front lens barrel holder.
5
0.5
22 1
6 1
1
3
1
1
∞
22
16
11
8
8
4
4
Front Lens Barrel Holder
Front Lens Barrel
Filter Select Ring
Filter Change Cam Ring
Connection Barrel
Positioning Pin
Filter Rotation Linkage Pin
U groove
Positioning Pin
Apply the anti-diffusion agent(A-20)
(All circumference)
(All circumference)
Apply the grease(G-30)
(All circumference)
(All circumference)
Apply the grease(G-30)
(All circumference)
(All circumference)
Apply the grease(G-30)(Rear side)
Filter Change
Cam Ring
Cam Ring
Filter Change Cam Ring
Hole
Filter Link Lever
Positioning Pin
Connection Barrel
Filter Rotation Linkage Pin
Click on the first or last page to see other SAL16F28 service manuals if exist.