DOWNLOAD Sony SAL1680Z Service Manual ↓ Size: 2.16 MB | Pages: 98 in PDF or view online for FREE

Model
SAL1680Z
Pages
98
Size
2.16 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
sal1680z.pdf
Date

Sony SAL1680Z Service Manual ▷ View online

HELP
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
 DT 16-80mm F3.5-4.5 ZA)
HELP14
Grease (G-15): J-6082-619-A
1.
Install the coupler adjustment washer to the location shown in the figure.
2.
Apply the grease (G-15) to the gear C.D block and the indicated portion of AF coupler.
And install them.
HELP15
1.
Set the focus ring to the 
∞ side.
2.
Peel off the polyester tape fixing the main flexible unit shown in the figure and lift up a little the main flexible unit with tweezers.
3.
Install the focus brush with two screws.
Note:
Install the focus brush in the direction shown in the detailed figure.
Coupler Adjustment Washer
Apply the grease (G-15) 
(Gear)
Apply the grease (G-15) 
(Gear)
Apply the grease (G-15) 
(Top of shaft)
Coupler Bush
AF Coupler
Gear C.D Block
Apply the grease (G-15) 
(Side edge of gear)
Apply the grease (G-15) 
(Shaft)
Focus Brush
Polyster Tape
Main Flexible Unit
Screw
HELP
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
 DT 16-80mm F3.5-4.5 ZA)
HELP16
Adhesive bond (B-40): J-6082-614-A
1.
Set the zoom to the tele end.
2.
Set the index with red color of 1st lens holder block to the focus scale window side and push the guide bush at three locations in the
guide groove straightly.
3.
Apply the adhesive bond (B-40) to the screwed portion of zoom coupling pin and tighten the zoom coupling pin.
HELP17
1.
Align the projection of focus ring B of MF operation ring block with the pinch lever.
2.
Aligning three projections of focus ring B with three cut portions of outer tube, install the focus ring B.
Then, holding its lower part by hand, turn clockwise the MF operation ring block and install it.
Guide groove
Index with red color
Guide bush
Index with 
red color
Guide groove
Focus Scale Window
Apply the adhesive bond (B-40)
Zoom Coupling Pin
MF Operation Ring
Cut portion of outer tube
Pinch Lever
Projection of focus ring B
Hold this portion 
and turn it.
HELP
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
 DT 16-80mm F3.5-4.5 ZA)
HELP18
Anti-diffusion agent (A-20): J-6082-611-A
Adhesive bond (B-40):
J-6082-614-A
Grease (G-35):
J-6082-621-A
Grease (G-55):
J-6082-623-A
Grease (G-115):
J-6082-627-A
Grease (G-116):
J-6082-628-A
Grease (G-117):
J-6082-660-A
1.
Apply the anti-diffusion agent (A-20) and following grease (G-B) to the indicated portion of MF operation ring.
Grease (G-B) = (G-116 : G-117 = 1 : 2)(Mix grease at the following rates before using the grease, and mix grease enough.)
2.
Apply the anti-diffusion agent (A-20), grease (G-35) and following grease (G-A) to the indicated portion of torque ring holder.
Grease (G-A) = (G-115 : G-117 = 1 : 2)(Mix grease at the following rates before using the grease, and mix grease enough.)
3.
Assemble the torque ring holder into the MF operation ring in the direction shown in the figure until it clicks.
4.
Apply small amount of the adhesive bond (B-40) to the screw hole of pinch lever (Wipe seeping out bond off) and install the pinch
lever to the MF operationring by the pinch lever shaft. (two locations)
5.
Apply small amount of the adhesive bond (B-40) to the screw hole of pinch lever B (Wipe seeping out bond off) and install the pinch
lever B to the MF operation ring by the pinch lever shaft. (One location)
6.
Affix the friction sheet A to the inner side of focus ring B.
7.
Apply the anti-diffusion agent (A-20), grease (G-55) and following grease (G-A) to the indicated portion of torque ring.
Grease (G-A) = (G-115 : G-117 = 1 : 2)(Mix grease at the following rates before using the grease, and mix grease enough.)
Note:
Wipe out the extra grease (G-55) on the area other than the indicated portion.
8.
Assemble the MF operation ring, focus ring B and torque ring (setting the spring) in the orders shown in the figure.
Friction 
Sheet A
Pinch Lever Shaft 
Pinch Lever B
(Apply small amount
of the adhesive bond
(B-40) to the screw hole)
(Do not seep out)
Pinch Lever B
(Apply small amount
of the adhesive bond
(B-40) to the screw hole)
(Do not seep out)
MF Operation Ring
Torque Ring Holder
Focus Ring B
Friction Sheet A
Spring
Torque Ring
Pinch Lever Shaft 
Apply the grease 
(G-A)
(Three locations)
Apply the anti-diffusion 
agent (A-20)
(All circumference)
Apply the anti-diffusion 
agent (A-20)
(All circumference)
Apply the anti-diffusion 
agent (A-20)
(All circumference)
Apply the grease (G-A)
(All circumference)
Apply the grease (G-A)
(All circumference)
Apply the grease (G-55)
(All circumference)
Apply the grease 
(G-35)
(All circumference)
Apply the grease 
(G-B)
(All circumference)
HELP
SAL1680Z (Vario-Sonnar DT 3.5-4.5/16-80 ZA) (Vario-Sonnar T
*
 DT 16-80mm F3.5-4.5 ZA)
HELP19
Grease (G-15): J-6082-619-A
1.
Apply the grease (G-15) to the gear of focus ring and the indicated portion.
2.
Rotate clockwise the focus lens holder as far as it goes and set the zoom to the wide end.
3.
Place the long side of focus stopper to the gear side as shown in the figure and install it in the groove of focus ring.
4.
Aligning the end of gear of focus ring with the hole of outer barrel as shown in figure, assemble the focus ring into the outer barrel
assembly.
5.
Turn a little clockwise the focus ring so that the screw holes of focus stopper can be seen in the two holes of outer barrel assembly.
6.
Tighten two screws.
Long
Short
Focus Ring
Focus Stopper
Focus Lens Holder
Screws
Apply the grease 
(G-15)
(All circumferences)
Outer Barrel Assy
Apply the grease (G-15) 
(Gear)
Page of 98
Display

Click on the first or last page to see other SAL1680Z service manuals if exist.