Sony SAL1635Z Service Manual ▷ View online
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
HELP11
1.
Peel off the released paper of encoder printed wiring board, smooth out the bended encoder printed wiring board.(Fig.a)
2.
Affix the encoder printed wiring board aligning at the lower left of step of outer barrel.(Fig.b)
Note:
Affix the encoder printed wiring board from reference to A part.(Fig.c)
3.
Peel off the released paper of the remainder, bend along the outer shape of outer barrel.(Fig.d/Fig.e)
4.
Affix the encoder printed wiring board aligning at the lower right of step of outer barrel.(Fig.f)
5.
Corrugate B part of the encoder printed wiring board from the outside internally. (Fig.g)
6.
Bend the B part of encoder printed wiring board to the lower direction of step of outer barrel.(Fig.h)
Released Paper
Smooth out the bended encoder printed wiring board
Fig.a
Reference to affixing
A Part
Fig.b
Fig.c
Outer Barrel
Released Paper
Fig.d
Fig.e
Bend the encoder printed wiring board
Fig.f
Fig.g
Fig.h
Reference to affixing
B Part
B Part
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
HELP12
1.
Fold upward the flexible board of switch assy at the locations shown in the figure.
2.
Inserting the flexible board of Switch assy in the hole of outer barrel, affix the Switch assy to the outer barrel by the SW adhesive
sheet.
3.
Affix the flexible board (Switch Assy) to the step of inside of the outer barrel.
Note:
Affix it with no place under the flexible board.
Switch Assy
Flexible Board
Valley fold
Flexible Board
SW Adhesive Sheet
Switch Assy
Flexible
Board
Board
Outer Barrel
SW Adhesive sheet
(Included in Switch assy)
(Included in Switch assy)
Flexible Board (Switch Assy)
Step of inside of the Outer Barrel
Affix it with no place under
the flexible board.
the flexible board.
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
HELP13
Adhesive bond (B-40): J-6082-614-A
1.
Turn the focus connect plate of the SSM block assy to near end in the arrow direction.
2.
Turn the U groove of the optics block assy to near end in the arrow direction.
3.
Install the SSM block assy to the optics block assy.
Note:
Align the focus connect plate of the SSM block assy with the U groove of optics block assy.
SSM Block Assy
Focus Connect Plate
U Groove
Turn to near end.
Optics Block Assy
Focus Connect Plate
U Groove
SSM Block Assy
Optics Block Assy
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
4.
Align the convex portion of focus operation ring with the concave portion of focus connect ring by rotating the focus operation ring
and drop completely the SSM block assy in the optics block assy.
5.
Tighten one screw. (one location)
6.
Apply the adhesive bond (B-40) to about two threads from the tips of screws and tighten the SSM block assy with the screws. (three
locations)
SSM Block Assy
Convex portion of
Focus Operation Ring
Focus Operation Ring
Concave portion of
Focus Connect Ring
Focus Connect Ring
SSM Block Assy
Optics Block Assy
Optics Block Assy
Apply the adhesive
bond (B-40).
bond (B-40).
Click on the first or last page to see other SAL1635Z service manuals if exist.