Sony SAL1635Z Service Manual ▷ View online
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
HELP14
Grease (G-119) : J-6082-708-A
Adhesive bond (B-40): J-6082-614-A
1.
Apply the grease (G-119) to the indicated portion of focus operation ring block assy.
2.
Install the focus operation ring block assy, aligning the hole at the upper side of the focus operation ring block assy with the round
concave portion of the optics block assy.
3.
Install the focus operation ring hold roll in the holes (three locations) at the upper side of the focus operation ring block assy.
Apply the adhesive bond (B-40) to about two threads from the tips of screws and tighten the focus operation ring hold rolls with
screws.
Focus Operation Ring Block Assy
Cross section
Inside
Apply the grease
(G-119)
(G-119)
Apply the grease
(G-119)
(G-119)
Apply the grease
(G-119)
(G-119)
Focus Operation Ring Block Assy
Focus Operation Ring Hold Roll
Focus Operation Ring Hold Roll
Focus Operation Ring Hold Roll
Holes at Upper side
Optics Block Assy
Round Concave Portion
Apply the adhesive
bond (B-40).
bond (B-40).
Apply the adhesive
bond (B-40).
bond (B-40).
Apply the adhesive
bond (B-40).
bond (B-40).
HELP
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
HELP15
Adhesive Bond (B-10): J-6082-612-A
1.
Apply the adhesive bond (B-10) to the diagonally-positioned inner screwed portions of 5th front lens holder in 3mm length.
G17 Holding Washer
5th Front Lens Holder
3mm
3mm
Apply the adhesive
bond (B-10).
bond (B-10).
3-1
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
DISASSEMBLY
(JAPANESE)
DISASSEMBLY
(ENGLISH)
3. REPAIR PARTS LIST
13
15
14
16
17
18
19
20
20
18
20
ns
(See Page 3-2.)
8
12
9
10
2
11
(Note 2)
ns
1
6
5
3
5
7
4
(Note 1)
Ref. No.
Part No.
Description
1
3-288-762-02 FRONT DECORATION RING (Note 1)
2
3-452-458-01 SHIELDING BELT A
3
4-120-050-01 PIN, CONDUCTION
4
4-120-049-01 SPRING, COMPRESSION
5
2-688-977-01 SCREW M1.6
6
X-2319-969-1 FRONT LENS BARREL BLOCK ASSY
7
3-288-760-01 FOCUS RUBBER RING
8
3-288-883-01 SHIELDING BELT B
9
X-2319-965-1 OUTER BLOCK ASSY, REAR
10
2-683-692-01 CHIP (MOUNT INDEX)
11
2-899-301-01 MOUNT SHIELDING O-RING
12
Selection Parts BACK ADJUSTMENT WASHER (Note 2)
13
4-104-671-01 PRESET RING HOLDING PLATE
14
A-1547-568-A PRESET RING BLOCK ASSY
15
3-288-885-01 MAIN SPRING
16
X-2319-968-1 MOUNT BLOCK ASSY
17
2-684-244-01 STOPPER SCREW
18
3-254-081-01 SCREW
19
3-288-758-01 REAR LIGHT SHIELD BARREL
20
2-684-064-01 SCREW M1.4
Ref. No.
Part No.
Description
(Note
1)
前飾り環(図面番号1)は,
できる限り交換を避けてく
ださい。
交換が必要な場合は, ユーザーに「Carl Zeiss Serial
交換が必要な場合は, ユーザーに「Carl Zeiss Serial
No.」が変更になる事をお伝えし,
了解を得てから交
換を行ってください。
(Note 1)
Be sure avoiding replacement of front decoration ring
(Ref. No. 1) as far as possible.
If replacement of it should be need, you convey the
message to your user that changing of the “Carl Zeis
Serial No.” is needed, and then you may obtain user's
agreement, and replace it.
(Ref. No. 1) as far as possible.
If replacement of it should be need, you convey the
message to your user that changing of the “Carl Zeis
Serial No.” is needed, and then you may obtain user's
agreement, and replace it.
(Note
2)
これらの部品は調整などによって使用個数や種類を
選択する必要があります。
3-4ページを参照して選択してください。
(Note 2)
The number or type of these parts need to be selected
according to adjustment etc..
Select the part referring to page 3-4.
according to adjustment etc..
Select the part referring to page 3-4.
3-1.
EXPLODED VIEWS
3-1-1. FRONT LENS BARREL BLOCK ASSY AND MOUNT BLOCK ASSY
NOTE:
•
•
-XX and -X mean standardized parts, so they may
have some difference from the original one.
have some difference from the original one.
•
Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
seldom required for routine service. Some delay
should be anticipated when ordering these items.
•
The mechanical parts with no reference number in
the exploded views are not supplied.
the exploded views are not supplied.
ns: not supplied
3-2
SAL1635Z (Vario-Sonnar 2.8/16-35 ZA T
*
SSM) (Vario-Sonnar T
*
16-35mm F2.8 ZA SSM)
DISASSEMBLY
(JAPANESE)
DISASSEMBLY
(ENGLISH)
Ref. No.
Part No.
Description
51
2-695-423-11 SCREW (M1.6)
52
2-899-279-01 BRUSH
53
X-2319-967-1 OUTER BARREL BLOCK ASSY
54
1-878-178-11 ENCODER PRINTED WIRING BOARD
55
3-218-125-01 CZ LABEL
56
A-1237-964-A SWITCH ASSY
57
4-123-846-01 SW ADHESIVE SHEET
58
X-2319-966-1 MR BLOCK ASSY
59
3-078-890-01 SCREW, TAPPING
60
Selection Parts ANTI SLIP RUBBER (Note 1)
61
3-270-376-01 SCREW
62
3-288-757-02 ZOOM BARREL
63
3-288-759-01 ZOOM LINKAGE PLATE
64
2-685-576-01 PHI 3 HEAD SCREW M1.6
65
2-895-533-01 SUS SHEET A
66
9-913-210-03 POLYESTER TAPE (BLACK)10mm (Note 2)
67
2-898-456-01 GND BRACKET
68
3-291-625-01 ZOOM RUBBER RING
69
A-1554-096-A SSM PC BOARD ASSY
70
2-684-844-01 CONNECTION BOX
71
2-580-751-01 SHEET, POLYIMIDE (Note 3)
Ref. No.
Part No.
Description
(Note 3)
Cut the polyimide sheet (Ref. No. 71) for specified size.
(Note 1)
Select the type of part according to the operation load of
the associated parts.
Select the part referring to page 3-4.
the associated parts.
Select the part referring to page 3-4.
(Note
3)
ポリイミドシート(図面番号71)は,
指定の寸法に
カットして使用してください。
(Note
1)
関連部品の動作の重さに合わせて,
種類を選択して
ください。
ください。
3-4ページを参照して選択してください。
ns: not supplied
(Note 1)
(Note 1)
53
51
60
66
52
ns
ns
ns
(See Page 3-3.)
54
55
56
57
58
59
60
61
61
62
63
64
59
51
67
68
65
69
71
70
59
52
(Note 2)
(10 x 45mm)
(10 x 45mm)
(Note 3)
(6mm × 25mm)
(6mm × 25mm)
3-1-2. OUTER BARREL BLOCK ASSY AND SSM PC BOARD ASSY
(Note 2)
Cut the polyester tape (black) 10mm (per roll) (Ref.
No.66) for specified size.
No.66) for specified size.
(Note
2)
ポリエステルテープ(黒)10mm(図面番号66)は,
指定
の寸法にカットして使用してください。
の寸法にカットして使用してください。
Click on the first or last page to see other SAL1635Z service manuals if exist.