Sony SAL14TC Service Manual ▷ View online
SAL14TC (1.4x TELE CONVERTER) (1.4 X Teleconverter)
1-3
1-5.
TROUBLESHOOTING
1-5-1. Aperture Trouble
1-5-2. Focus Trouble
Position NG
Fcous Trouble
Replace the BL contact
holder block
END
Check operation of the
preset ring, and replace
the defective part.
F No. NG
Aperture trouble
END
2-1
SAL14TC (1.4x TELE CONVERTER) (1.4 X Teleconverter)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
Ver 1.1 2007.01
2-2
SAL14TC (1.4x TELE CONVERTER) (1.4 X Teleconverter)
2-1.
DISASSEMBLY
2-1-1. LENS MOUNT BLOCK, LENS BLOCK AND BODY A MOUNT
EXPLODED VIEW
2
Rear Light Shield
Barrel
1
Ground Spring
HELP01
3
Lens Mount
Block
Fitting Tube Block
HELP04
HELP09
HELP05
7
Body A Mount
8
Ring Spring
HELP08
5
Lens
Block
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
HELP03
6
Back
Adjustment
Washer
Washer
(See Page 2-3.)
4
Coupler
!=
Gear Base
Plate Block
!-
Lock Pin
0
Lever Base
Plate Unit
9
Lock Holding
Lever Block
HELP07
HELP06
HELP02
2-3
SAL14TC (1.4x TELE CONVERTER) (1.4 X Teleconverter)
2-1-2. CONNECT BAREL AND FIXED BARREL
EXPLODED VIEW
HELP12
HELP14
HELP11
HELP11
HELP16
HELP15
HELP13
HELP17
HELP18
HELP18
HELP13
HELP10
PRESET LEVER
ADJUSTMENT
8
Preset Ring Retainer
4
Fixed Barrel
5
BL Contact
Holder Block
2
Screw
1
Ground Spring A
!=
Preset Ring
7
Main
Spring
9
Steel Ball
!-
Preset
Lever
3
Protector Rubber
6
Lock
Spring
!/
Preset
Lever B
Connect
Barrel
Barrel
Click on the first or last page to see other SAL14TC service manuals if exist.