Sony SAL135F18Z Service Manual ▷ View online
2-1
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
When top of tip does not reach holes or notches because the fixed screw becomes obstructive,
replace the fixed screw to below.
+B 3X5 7-682-546-09
replace the fixed screw to below.
+B 3X5 7-682-546-09
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
2-1.
DISASSEMBLY
Note 1:
Remove the filter screw frame using the filter screw frame removing tool.
Filter screw frame removing tool: J-6082-649-A
Note 2:
When removing or installing the parts of side of lens mount, install the filter screw frame to lens.
If removing or installing the parts of side of lens mount after the filter screw frame is removed, be careful to avoid damaging the 1 lens
block.
Note 3:
Remove the screw (Ref. No. 15 or 61, 2-897-949-01 screw (3ULR-F M1.7x1.6(C3C))) using the special driver.
Special driver: J-6082-654-A
Shape of head
2-3
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
2-1-1. OUTER BARREL BLOCK, MOUNT BLOCK AND LIGHT SHIELD RING BLOCK
EXPLODED VIEW
A
A
HELP01
HELP10
HELP10
HELP07
HELP09
HELP11
HELP02
HELP03
HELP08
HELP05
HELP04
HELP06
HELP12
(See Page 2-4.)
HELP07
8
1 Screw Filter Frame
Assy
Assy
Function Lever
Preset Ring
!- Rear Ring Assy
9 Contact Flexible
Guide
Guide
!= PWB Flexible Main
Assy
Assy
2 Draw Ring Assy
3 Focus Ring
!/ Main Spring
Guide
Guide
5 Contact Flexible
4 Ligth Shield Ring Block
6 Mount Block
![ Outer Barrel Block
7 Coupler Receive
APERTURE
DIAMETER
ADJUSTMENT
DIAMETER
ADJUSTMENT
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
TOUQUE RING PLAY
ADJUSTMENT
ADJUSTMENT
• In case the removing of screw filter frame assy :
Before removing the screw filter frame assy, lubricate a small solvent (alcohol) to a gap
between screw filter frame assy and draw ring assy, hereby dissolve the adhesive bond.
Then remove it.
• About the screw filter frame assy :
Be sure avoiding replacement of screw filter frame assy as far as possible. If replacement of
it should be need, you convey the message to your user that changing of the Carl Zeiss
Serial No. is needed, and then you may obtain user’s agreement, and it replace.
Before removing the screw filter frame assy, lubricate a small solvent (alcohol) to a gap
between screw filter frame assy and draw ring assy, hereby dissolve the adhesive bond.
Then remove it.
• About the screw filter frame assy :
Be sure avoiding replacement of screw filter frame assy as far as possible. If replacement of
it should be need, you convey the message to your user that changing of the Carl Zeiss
Serial No. is needed, and then you may obtain user’s agreement, and it replace.
Note:
2-4
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
2-1-2. 1, 2, 3 AND 4 LENS BLOCK
EXPLODED VIEW
A
A
B
B
C
C
HELP13
HELP15
HELP16
HELP14
HELP18
HELP17
HELP20
1 1 Lens Block
2 Ornamental 2 Sheet
4 2 Lens Blcok
5 Iris Block
PROJECTIVE RESOLVING
POWER CHECK
POWER CHECK
6 3 Lens Block
HELP19
7 4 Lens Block
PROJECTIVE RESOLVING
POWER CHECK
POWER CHECK
8 Scale Focus Sheet
3 Zoom Brush
FOCUS BRUSH
POSITION CHECK
POSITION CHECK
In case the installing of 1 lens block :
Install the 1 lens block placed with same position of removing it to the length grove barrel assy.
* When removing the 1 lens block, put the marks of both the 1 lens block and length grove
barrel assy.
Install the 1 lens block placed with same position of removing it to the length grove barrel assy.
* When removing the 1 lens block, put the marks of both the 1 lens block and length grove
barrel assy.
Note:
Click on the first or last page to see other SAL135F18Z service manuals if exist.