Sony SAL135F18Z Service Manual ▷ View online
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
F-ECD Flexible
Gear
D2
D3
D1
HELP18
Adhesive bond (B-40): J-6082-614-A
1.
Rotate the focus 2 cam ring block so that the position of relationship between the F-ECD flexible and the gear is as shown in figure.
2.
Install the 3 group lens block to the length grove barrel assy. Apply the adhesive bond (B-40) to the screwed portions of 3-roller
screws. Then, fix the 3 group lens block with the 3 roller and the 3-roller screws at three locations.
Note:
• When assembling, do not touch the lens.
• Use the 3 roller with a play of 0 to 0.010mm with respect to the groove width of length grove barrel assy.
Part Code
Part Name
Diameter
D1
D2
D3
2-897-899-01
3 A roller
3.99
4.50
3.48
2-897-900-01
3 D roller
3.99
4.51
3.48
3.
Confirm that the focus cam 2 ring block rotates smoothly.
3 Lens Block
3 Roller (3 places)
F-ECD Flexible
Gear
3 Roller Screw
(Apply the adhesive bond (B-40) (3 places)
(Apply the adhesive bond (B-40) (3 places)
Focus 2 Cam Ring Block
HELP
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
HELP19
1.
After removing the tilt adjustment washers, they should reinstall the replaced positions.
Note:
After replacing the lens block 4, install the three tilt adjustment washers D (0.1mm) as shown in figure.
2.
Install the 4 lens block, aligning it with positioning pins at three locations of length grove barrel assy. Then, tighten three screws to
fix the 4 lens block.
HELP20
Adhesive bond (B-10): J-6082-612-A
Special driver:
J-6082-654-A
1.
Affix the focus scale to meet the length grove barrel assy (vertical, horizontal).
Note:
• Confirm that the focus scale is not floated.
• Confirm that the surface of focus scale is clean.
2.
Expose both ends of focus scale by peeling off the protection tape so that screws can be tightened.
3.
Fix the focus scale with two screws. (Use the special driver: J-6082-654-A)
4.
Apply the adhesive bond (B-10) to the heads of screws.
Length Grove Barrel Assy
Positioning Pins
Positioning Pins
4 Lens Block
Screws
Positionaing Pins
Tilt Adjustment Washer D
Tilt Adjustment Washer D
Focus Scale
Pasted standard
Horizontal
Pasted standard
Vertical
Screws
(Apply the adhesive bond (B-10))
(Apply the adhesive bond (B-10))
Length Grove Barrel Assy
3-1
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
A
A
1
2
3
3
3
4
4
5
4
6
7
8
9
10
10
11
7
7
12
13
14
15
16
17
8
18 10
10
19
20 21
22
7
7
23
24
24
7
(Note 2)
(Note 1)
(Note 2)
(Note 3)
ns
ns
ns
ns
ns
(See Page 3-2.)
(Note 1)
Be sure avoiding replacement of screw filter frame assy
(Ref. No. 1) as far as possible. If replacement of it should
be need, you convey the message to your user that chang-
ing of the “Carl Zeiss Serial No.” is needed, and then
you may obtain user's agreement, and it replace.
(Ref. No. 1) as far as possible. If replacement of it should
be need, you convey the message to your user that chang-
ing of the “Carl Zeiss Serial No.” is needed, and then
you may obtain user's agreement, and it replace.
3. REPAIR PARTS LIST
3-1.
EXPLODED VIEWS
3-1-1. OUTER BARREL BLOCK, MOUNT BLOCK AND LIGHT SHIELD RING BLOCK
DISASSEMBLY
Ref. No.
Part No.
Description
1
A-1223-858-A FRAME ASSY,SCREW FILTER (Note 1)
2
A-1224-100-A RING ASSY,DRAW
3
2-897-789-01 PIN,GUIDE
4
2-897-980-01 SCREW (1P 1.7X3.5 C3C)
5
2-897-981-01 RING, FOCUS
6
2-898-026-01 BARREL BLOCK, FOCUS HOLD
7
2-898-004-01 SCREW (1P 2X5.5 C3C)
8
2-897-887-01 SCREW (2P 1.7X4 BNI)
9
A-1226-230-A ASSY, PWB FLEXIBLE MAIN
10
2-898-117-01 SCREW (2P 1.7X2.2 BNI)
11
A-1224-099-A RING ASSY, REAR
12
2-695-839-01 LABEL, MODEL NAME
NOTE:
•
•
-XX and -X mean standardized parts, so they may
have some difference from the original one.
have some difference from the original one.
•
Items marked “*” are not stocked since they are
seldom required for routine service. Some delay
should be anticipated when ordering these items.
seldom required for routine service. Some delay
should be anticipated when ordering these items.
•
The mechanical parts with no reference number in
the exploded views are not supplied.
the exploded views are not supplied.
(Note 2)
The number or type of these parts need to be selected
according to adjustment etc..
Select the part referring to page 3-3.
according to adjustment etc..
Select the part referring to page 3-3.
Ref. No.
Part No.
Description
13
Selection parts RING (A-C), PRESET (Note 2)
14
2-898-008-01 LEVER, FUNCTION
15
2-897-949-01 SCREW (3ULR-F M1.7X1.6 C3C) (Note 3)
16
2-898-009-01 SPRING, MAIN
17
2-898-010-01 GUIDE, MAIN SPRING
18
2-898-011-01 GUIDE, CONTACT FLEXIBLE
19
Selection parts WASHER (A, B, D, F), FB ADJUSTMENT (Note 2)
20
2-898-016-01 COUPLER
21
2-886-787-01 COUPLER RECEIVE
22
2-898-017-01 BLOCK, MOUNT
23
2-898-020-01 RING BLOCK, LIGHT SHIELD
24
2-898-024-01 SCREW (2P 1.4X2.2 BNI)
ns: not supplied
(Note 3)
Remove the screw (Ref. No. 15) using the
special driver.
special driver.
3-2
SAL135F18Z (Sonnar 1.8/135 ZA) (Sonnar T
*
135mm F1.8 ZA)
A
A
B
B
C
C
51
52
53
54
58
55
62
64
64
64
68
68
68
68
66
67
(Note 1)
67
(Note 1)
67
(Note 1)
67
(Note 1)
67
(Note 1)
65
61
69
61
66
(Note 1)
(Note 3)
(Note 3)
65
(Note 1)
65
66
(Note 1)
(Note 1)
62
(Note 1)
62
(Note 1)
ns
ns
63
68
60
(Note 2)
(Note 3)
61
59
59
59
70
3-1-2. 1, 2, 3 AND 4 LENS BLOCK
DISASSEMBLY
Ref. No.
Part No.
Description
51
A-1223-863-A LENS BLOCK, 1
52
2-897-794-01 LENS, G01
53
2-897-805-01 SHEET,ORNAMENTAL 2
54
A-1223-877-A LENS BLOCK, 2
55
2-897-892-01 BLOCK, IRIS
58
A-1224-031-A LENS BLOCK, 3
59
2-897-950-01 SCREW (HEXAGONAL M2X5.5 C3C)
60
X-2177-204-1 LENGTH GROVE BARREL ASSY (Note 2)
61
2-897-949-01 SCREW (3ULR-F M1.7X1.6 C3C) (Note 3)
Ref. No.
Part No.
Description
(Note 2)
Refer to page 3-3 for detail of parts of the length grove
barrel assy (Ref. No. 60).
barrel assy (Ref. No. 60).
62
Selection parts WASHER (A, B, D), TILT ADJUSTMENT (Note 1)
63
A-1224-069-A LENS BLOCK, 4
64
2-897-887-01 SCREW (2P 1.7X4 BNI)
65
Selection parts ROLLER (C, K, L) , 2 (Note 1)
66
2-897-891-01 SCREW, 2 ROLLER
67
Selection parts ROLLER (A, D), 3 (Note 1)
68
2-897-898-01 SCREW, ROLLER 3
69
2-897-972-01 SHEET, SCALE FOCUS
70
2-897-971-01 BRUSH, ZOOM
(Note 1)
The number or type of these parts need to be selected
according to adjustment etc..
Select the part referring to page 3-3.
according to adjustment etc..
Select the part referring to page 3-3.
(Note 3)
Remove the screw (Ref. No. 61) using the special driver.
Click on the first or last page to see other SAL135F18Z service manuals if exist.