Sony SAL100M28 Service Manual ▷ View online
4-16
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
4-7.
BRUSH POSITION CHECK/ADJUSTMENT AND PATTERN CHECK
Note:
If dialog box of error code appears during the checking or adjustment, check the reason of error referring to page 4-19.
4-7-1. Brush Position Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Connect the checking lens to the camera.
2)
Start the lens adjustment program “LensAdjustment.exe” referring to “4-1-2. Lens Adjustment Program”.
Fig. 4-7-1
2. Checking Method
1)
Click the
[Connect]
button on the lens adjustment program.
Note:
Click the
[End]
button to disconnect the USB connection, then lens adjustment program will terminate.
Fig. 4-7-2
2)
Check that the “Type” is set to “1”, and click the
[Focus]
button on the lens adjustment program.
3)
Set the focus position to infinity end, then check that the OK (Green) indicator of “Position” lights as shown in Fig. 4-7-3.
Fig. 4-7-3
If the NG (Red) indicator of “Position” lights, perform the “4-7-2. Brush Position Adjustment and Pattern Check”.
Fig. 4-7-4
4)
Click the
[Exit]
button.
5)
Click the
[End]
button to terminate the lens adjustment program.
6)
Turn the POWER switch of the camera to OFF.
4-17
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
4-7-2. Brush Position Adjustment and Pattern Check
Equipment
• Personal Computer (PC)
• Camera DSLR-A100
• USB Cord With Connector
• Adhesive bond (B-10)
• Lens Adjustment Program
Note:
Lens Adjustment Program is downloadable from the ESI homepage.
1. Preparations
1)
Disassemble or assemble the checking lens into the state of the Fig. 4-7-5.
2)
Turn the focus cam ring A to the infinity side until it stops at the focus stopper.
Fig. 4-7-5
2. Brush Position Adjustment
1)
Loosen the four screws as shown in the Fig. 4-7-6.
Fig. 4-7-6
2)
Perform the “4-7-1. Brush Position Check”, and adjust the A encoder brush position until the OK (Green) indicator of “Position”
lights.
Fig. 4-7-7
3)
Tighten the four screws loosened in step 1).
Turn the focus cam ring A
until it stops at the focus stopper.
until it stops at the focus stopper.
Focus Cam Ring A
Screws
Screws
4-18
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
3. Pattern Check
Note:
When the NG (Red) indicator of “Position” lights during checking, does not care about it (It is normal performance).
1)
Turn the focus ring (focus cam ring A) slowly from the near end “Focus Pattern : 1” to the infinity end “Focus Pattern : 51” and check
that the value of “Focus Pattern” change from 1 to 51 continuously.
2)
Turn the focus ring (focus cam ring A) slowly from the infinity end “Focus Pattern : 51” to the near end “Focus Pattern : 1” and check
that the value of “Focus Pattern” change from 51 to 1 continuously.
Fig. 4-7-8
3)
Click the
[Exit]
button.
4)
Click the
[End]
button to terminate the lens adjustment program.
5)
Turn the POWER switch of the camera to OFF.
6)
After the pattern check is completed, apply the adhesive bond (B-10) as shown in Fig. 4-7-9.
Fig. 4-7-9
h
h
h
h
h
Apply the adhesive
bond (B-10)
bond (B-10)
4-19
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
4-8.
ERROR CODE LIST
Error code
Description
Corrupt Data
Zoom/focus data of check pattern is out of sync with the number of check pattern.
Error, No Lens
Lens is not connected correctly.
Error, Unknown Lens
Unidentified lens is connected.
Communication Error,
Code#:E600
Communication error with the camera
Code#:F000
Input data error to DLL file
Code#:F100
Setting error of USB port
Code#:2531
Communication error of main signal on the camera
Click on the first or last page to see other SAL100M28 service manuals if exist.