Sony SAL100M28 Service Manual ▷ View online
1-3
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
1-5.
TROUBLESHOOTING
1-5-1. Aperture Trouble
Ver 1.1 2007.02
NG
Check operation of
the joint tube block.
Replace the defective part.
Check operation of the
joint tube block,
and replace the
and replace the
defective part.
Replace the midway
move frame block.
Perform the aperture
diameter check.
(See page 4-4.)
NG
Check operation
of the midway move
frame block.
OK
OK
OK
Function NG
F No. NG
Aperture trouble
Replace the defective part.
NG
NG
NG
END
OK
Perform the aperture
diameter check.
(See page 4-4.)
1-4
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Check the operation
again.
Replace the defective part
or apply the grease.
OK
NG
OK
OK
OK
OK
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the coupler,
coupler gear and gear
base plate block.
Check the fixed holding
tube block and
fixed tube block.
NG
NG
NG
NG
NG
END
OK
Check the position
and deformation
at the tip of the
A encoder brush.
Adjust the position, or replace
the A encoder brush.
Check pattern
of the main flexible block.
Clean the pattern of the
main flexible block.
Replace the
main flexible block.
Perform the
brush position
check/adjustment.
(See page 4-16.)
1-5-2. Foucus Trouble
2-1
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
When top of tip does not reach holes or notches because the fixed screw becomes obstructive,
replace the fixed screw to below.
+B 3X5 7-682-546-09
replace the fixed screw to below.
+B 3X5 7-682-546-09
Notches
Holes
Universal wrench
J-6082-609-A
J-6082-609-A
Chip-A for
universal wrench:
J-6082-609-1
universal wrench:
J-6082-609-1
Chip-B for
universal wrench:
J-6082-609-2
universal wrench:
J-6082-609-2
Ver 1.1 2007.02
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench
to the width of holes or notches.
to the width of holes or notches.
Universal wrench
Holes
2-2
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
2-1.
DISASSEMBLY
2-1-1. LENS MOUNT BLOCK AND JOINT TUBE BLOCK
A
B
C
D
C
B
D
A
(See Page 2-3.)
2
Rear Light
Shield Barrel
4
Main Flexible
Block
5
Joint Tube
Block
3
Lens Mount
Block
1
Main Flexible Block
HELP01
HELP02
HELP06
HELP04
HELP03
EXPLODED VIEW
HELP05
HELP42
HELP04
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
FLANGE BACK
ADJUSTMENT
ADJUSTMENT
Click on the first or last page to see other SAL100M28 service manuals if exist.