DOWNLOAD Sony SAL100M28 Service Manual ↓ Size: 1.7 MB | Pages: 70 in PDF or view online for FREE

Model
SAL100M28
Pages
70
Size
1.7 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
sal100m28.pdf
Date

Sony SAL100M28 Service Manual ▷ View online

1-2
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
1-4.
SAFETY CHECK-OUT
After correcting the original service problem, perform the following safety checks before releasing the set to the customer.
1.
Check the area of your repair for unsoldered or poorly-soldered connections. Check the entire board surface for solder splashes and
bridges.
2.
Check the interboard wiring to ensure that no wires are “pinched” or contact high-wattage resistors.
3.
Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the
customer and recommend their replacement.
4.
Look for parts which, through functioning, show obvious signs of deterioration. Point them out to the customer and recommend their
replacement.
5.
Check the B+ voltage to see it is at the values specified.
6.
Flexible Circuit Board Repairing
• Keep the temperature of the soldering iron around 270 
°C during repairing.
• Do not touch the soldering iron on the same conductor of the circuit board (within 3 times).
• Be careful not to apply force on the conductor when soldering or unsoldering.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 
0
 OR DOTTED LINE WITH
MARK 
0
 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 
0
 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
1-3
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
1-5.
TROUBLESHOOTING
1-5-1. Aperture Trouble
Ver 1.1  2007.02
NG
Check operation of
the joint tube block.
Replace the defective part.
Check operation of the
joint tube block,
and replace the
defective part.
Replace the midway
move frame block.
Perform the aperture 
diameter check. 
(See page 4-4.)
NG
Check operation
of the midway move
frame block.
OK
OK
OK
Function NG
F No. NG
Aperture trouble
Replace the defective part.
NG
NG
NG
END
OK
Perform the aperture 
diameter check.
(See page 4-4.)
1-4
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Check the operation
again.
Replace the defective part
or apply the grease.
OK
NG
OK
OK
OK
OK
Function NG
Position NG
Focus trouble
Replace the defective part
or apply the grease.
Check the coupler,
coupler gear and gear
base plate block.
Check the fixed holding
tube block and
fixed tube block.
NG
NG
NG
NG
NG
END
OK
Check the position
and deformation 
at the tip of the
 A encoder brush.
Adjust the position, or replace
the A encoder brush.
Check pattern
of the main flexible block.
Clean the pattern of the 
 main flexible block.
Replace the
main flexible block.
Perform the 
brush position
check/adjustment.
(See page 4-16.)
1-5-2. Foucus Trouble
2-1
SAL100M28 (MACRO 2.8/100) (100mm F2.8 Macro)
Cut and remove the part of gilt 
which comes off at the point.
(Be careful or some 
pieces of gilt may be left inside) 
2. DISASSEMBLY
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, dont’ pull at wire of connector. It is possible that a wire is snapped.
• When installing a connector, dont’ press down at wire of connector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
UNIVERSAL WRENCH
In case of the following notches or holes are located in the lens block, etc during disassembling/
assembling the lens, Use the universal wrench.
How to Use
Attach the chip-A or chip-B to the universal wrench.
For the notches: chip-A
For the holes:
chip-B
Match the universal wrench to the holes or notches of the lens block, etc.
When top of tip does not reach holes or notches because the fixed screw becomes obstructive,
replace the fixed screw to below.
+B 3X5 7-682-546-09
Notches
Holes
Universal wrench
J-6082-609-A
Chip-A for 
universal wrench:
J-6082-609-1
Chip-B for 
universal wrench:
J-6082-609-2
Ver 1.1  2007.02
Notches
Chip-A
Chip-A
Chip-B
Chip-B
Chip
Fixed screw
Fixed screw
Chip
Match the universal wrench 
to the width of holes or notches.
Universal wrench
Holes
Page of 70
Display

Click on the first or last page to see other SAL100M28 service manuals if exist.