Sony NEX-FS100C / NEX-FS100CK / NEX-FS100E / NEX-FS100EK / NEX-FS100J / NEX-FS100JK / NEX-FS100N / NEX-FS100NK / NEX-FS100P / NEX-FS100PK / NEX-FS100U / NEX-FS100UK Service Manual ▷ View online
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
2-29E
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
R4803 1-208-893-11 METAL
CHIP
1.8K
0.5% 1/16W
R4804 1-218-953-11 METAL
CHIP
1K
5%
1/16W
R4807 1-208-703-11 METAL
CHIP
6.8K
0.5% 1/16W
R4808 1-218-973-11 METAL
CHIP
47K
5%
1/16W
R4809 1-218-953-11 METAL
CHIP
1K
5%
1/16W
R4810 1-218-949-11 METAL
CHIP
470
5%
1/16W
R4812 1-218-973-11 METAL
CHIP
47K
5%
1/16W
R4814 1-218-985-11 METAL
CHIP
470K
5%
1/16W
R4815 1-218-989-11 METAL
CHIP
1M
5%
1/16W
R4816 1-218-990-81 SHORT
CHIP
0
R4817 1-208-927-11 METAL
CHIP
47K
0.5% 1/16W
R4818 1-208-935-11 METAL
CHIP
100K
0.5% 1/16W
R4819 1-218-990-81 SHORT
CHIP
0
R4822 1-208-911-11 METAL
CHIP
10K
0.5% 1/16W
R4823 1-218-965-11 METAL
CHIP
10K
5%
1/16W
R4824 1-218-965-11 METAL
CHIP
10K
5%
1/16W
R4825 1-218-977-11 METAL
CHIP
100K
5%
1/16W
R4826 1-218-989-11 METAL
CHIP
1M
5%
1/16W
R4836 1-218-953-11 METAL
CHIP
1K
5%
1/16W
R4838 1-218-977-11 METAL
CHIP
100K
5%
1/16W
R4839 1-218-953-11 METAL
CHIP
1K
5%
1/16W
< COMPOSITION CIRCUIT BLOCK >
RB1301 1-234-372-11 RES,
NETWORK 100
(1005X4)
RB1302 1-234-381-11 RES,
NETWORK 100K
(1005X4)
RB1304 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1412 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1413 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1414 1-234-378-21
RES, NETWORK 10K (1005X4)
RB1419 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1420 1-234-378-21
RES, NETWORK 10K (1005X4)
RB1421 1-234-378-21
RES, NETWORK 10K (1005X4)
RB1422 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1423 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1424 1-234-375-21
RES, NETWORK 1K (1005X4)
RB1426 1-234-378-21
RES, NETWORK 10K (1005X4)
<
VARISTOR
>
VD001 1-802-078-11 VARISTOR
(SMD)
<
VIBRATOR
>
X1301
1-813-403-81
QUARTZ CRYSTAL OSCILLATOR (12Hz)
X1402
1-814-470-11
OSCILLATOR, CRYSTAL (25MHZ)
X4801
1-781-525-11
VIBRATOR, CRYSTAL (32.768khZ)
A-1826-061-A XL-014 (IN1) BOARD, COMPLETE
A-1826-061-A XL-014 (IN2) BOARD, COMPLETE
*************************
<
CONNECTOR
>
CN3001 1-766-386-14
CONNECTOR, 3P-XLR TYPE (FEMALE)
CN3002 1-816-654-61
FFC/FPC CONNECTOR (LIF) 6P
< COIL >
* L3001 1-481-425-21 INDUCTOR
10uH
* L3002 1-481-425-21 INDUCTOR
10uH
VC-618
XL-014
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
3-1
3. ASSEMBLY
Assembly-5: Apply grease on the MB N Plate SP.
MB N Plate SP
G
G-85
(J-6082-626-A)
Assembly-6: Apply grease on the LCD Lock Bolt.
LCD Lock Bolt
Screwing position
G
G-85
(J-6082-626-A)
Assembly-7: Putting position of the Fuse Replacement Caution
Label.
Putting position of
the Fuse Replacement Caution Label.
the Fuse Replacement Caution Label.
Fuse Replacement
Caution Label
Caution Label
Chip
VC-618 Board
Assembly-1: Installation Cautions of the FPC Clamp.
Assembly-2: Installation Cautions of the VC-618 Board.
Assembly-3: Installation Cautions of the AU Cover.
Assembly-4: Putting position of the IM Adjust Washer (A).
Mount Base
Adjust IM
Washer (A)
Washer (A)
Adjust IM Washer (A)
Adjust IM Washer (A)
3-1. ASSEMBLY
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
3-2
Optical Filter Block
Replacement of Optical Filter Block
When replacing the optical filter block, refer to the procedure below.
How to remove
(1) Pour a solution (alcohol or cleaning liquid) in between the IM flare
cutter and the imager.
* Wait until the adhesion of IM flare cutter tape becomes weak.
* Wait until the adhesion of IM flare cutter tape becomes weak.
(2) Remove the IM flare cutter from the imager.
How to assemble
(1) Set the IM flare cutter to the flare cutter adjustment jig (J-6082-
752-A), facing it up.
After setting it, peel the released paper.
After setting it, peel the released paper.
(2) Set the IM flare cutter tape to the jig, facing down its adhesive
side. Then, push it and peel the released paper.
(3) Set the image to the jig and affix the IM flare cutter to the imager
by pushing.
(4) Set the optical filter block to the flare cutter adjustment jig (J-
6082-753-A) with the IM flare cutter faced up.
(5) Set the imager to the jig and affix the optical filter block to the
imager by pushing.
Note: Be careful for dust not to enter.
Flare Cutter Adjustment Jig
J-6082-752-A
J-6082-752-A
Optical Filter Block Adjustment Jig
J-6082-753-A
J-6082-753-A
Optical Filter Block
IM Flare Cutter
Pin
Pin
Released Paper
Released Paper
IM Flare Cutter Tape
(The adhesive side faces down.)
(The adhesive side faces down.)
Two layer side is
Imager side
Imager side
Mount
Side
Side
Imager
Side
Side
Released
Paper
Paper
IM Flare Cutter
Pin
Imager
Optical Filter Block
Pin
Imager
Pour a solution (alcohol or cleaning liquid) in
between the IM flare cutter and the imager.
between the IM flare cutter and the imager.
NEX-FS100C/FS100CK/FS100E/FS100EK/FS100J/FS100JK/FS100N/FS100NK/FS100P/FS100PK/FS100U/FS100UK
3-3E
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to service manual, check if there is dirt on the CCD.
4. According to service manual, check if there is dirt on the CCD.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
Click on the first or last page to see other NEX-FS100C / NEX-FS100CK / NEX-FS100E / NEX-FS100EK / NEX-FS100J / NEX-FS100JK / NEX-FS100N / NEX-FS100NK / NEX-FS100P / NEX-FS100PK / NEX-FS100U / NEX-FS100UK service manuals if exist.