DOWNLOAD Sony NEX-F3D / NEX-F3K / NEX-F3Y Service Manual ↓ Size: 5.12 MB | Pages: 18 in PDF or view online for FREE

Model
NEX-F3D NEX-F3K NEX-F3Y
Pages
18
Size
5.12 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL2
File
nex-f3d-nex-f3k-nex-f3y.pdf
Date

Sony NEX-F3D / NEX-F3K / NEX-F3Y Service Manual ▷ View online

NEX-F3D/F3K/F3Y_L2
Sony Corporation
SERVICE MANUAL
Revision History
SERVICE  NOTE (Check the following note before the service.)
LEVEL 
2
983467033.pdf
2014E08-1
© 2014.05
Published by Sony Techno Create Corporation
Ver. 1.2  2014.05
INTERCHANGEABLE LENS DIGITAL CAMERA
US Model
Canadian Model
AEP Model
E Model
Australian Model
Chinese Model
Korea Model
Brazilian Model
Japanese Model
Tourist Model
1-1. 
PRECAUTION ON REPLACING THE SY-307 BOARD
1-2. ADDITION
 OF DESTINATION DATA FILE
9-834-670-33
Image: NEX-F3 (Main body)
[About the service of this model]
NEX-F3D/F3K/F3Y are commodity that packed the Interchangeable Lens Digital Camera and Interchangeable Lenses.
Refer to each following service manual the Interchangeable Lens kit, when you repair.
Model
Lens
Service Manual of Lens
NEX-F3D 
SEL16F28 (E 16 mm F2.8)
9-852-798-1[]
SEL1855 (E 18-55 mm F3.5-5.6 OSS) 
9-852-799-1[]
NEX-F3K 
SEL1855 (E 18-55 mm F3.5-5.6 OSS)
9-852-799-1[]
NEX-F3Y
SEL1855 (E 18-55 mm F3.5-5.6 OSS)
9-852-799-1[]
SEL55210 (E 55-210 mm F4.5-6.3 OSS)
9-834-603-1[]
 
– ENGLISH –
– JAPANESE –
1-1. 
SY-307基板交換時の注意
1-2. 
Destination Dataファイルの追加について
Ver.
Date
History
Contents
S.M. Rev.
issued
1.0
2012.05
Official Release
1.1
2012.09
Revised-1
(A1 12-231)
•  Correction of SERVICE NOTE.
 Page 
1-2
1-3
Yes
1.2
2014.05
Revised-2
(A2 14-018)
•  Change of REPAIR PARTS LIST.
 Page 
2-6
Yes
The components identified 
by mark 
0 or dotted line with 
mark 
0 are critical for safety.
Replace only with part number 
specified.
Les composants identifiés par 
une marque 
0 sont critiques 
pour la sécurité.
Ne les remplacer que par une 
pièce portant le numéro spécifié.
NEX-F3D/F3K/F3Y
Revised-2
Replace the previously issued
SERVICE MANUAL 9-834-670-32
with this Manual.
NEX-F3D/F3K/F3Y_L2
– 2 –
SPECIFICATIONS
– ENGLISH –
– JAPANESE –
概略仕様
Camera
[System]
Camera type: Interchangeable lens
 digital 
camera
Lens: E-mount lens
[Image sensor]
Image sensor: 23.5 × 15.6 mm (APS-C
 
format) CMOS image sensor
Total pixel number of image sensor:
 
Approx. 16 500 000 pixels
Effective pixel number of camera:
 
Approx. 16 100 000 pixels
[Anti-dust]
System: Charge protection coating on
 
Low-Pass Filter and ultrasonic
 vibration 
mechanism
[Auto focus system]
System: Contrast detection system
Sensitivity range: EV0 to EV20 (at ISO
 
100 equivalent, with F2.8 lens)
[Exposure control]
Metering method: 1 200-segment
 
metering by the image sensor
Metering range: EV0 to EV20 (at ISO
 
100 equivalent, with F2.8 lens)
ISO sensitivity (Recommended
 exposure 
index):
 
Still images: AUTO (ISO 200 –
 16 
000)
 
Movies: AUTO (ISO 200 – 3 200
 equivalent)
Exposure compensation: ±3.0 EV (1/3
 EV 
step)
[Shutter]
Type: Electronically-controlled,
 
vertical-traverse, focal-plane type
Speed range:
 
Still images: 1/4 000 second to 30
 
seconds (1/3 EV step), BULB
 
Movies: 1/4 000 second to 1/4
 
second, up to 1/30 in AUTO mode
 
(1/3 EV step)
Flash sync speed: 1/160 second
[Recording media]
“Memory Stick PRO Duo” media,
SD card
[LCD screen]
LCD panel: 7.5 cm (3.0 type) TFT
 drive
Total number of dots: 921 600 (640 × 3
 
(RGB) × 480) dots
[Input/output terminals]
USB: Micro USB type B connector
HDMI: HDMI type C minijack
[Power]
Used battery pack: Rechargeable
 
battery pack NP-FW50
[Others]
Exif Print: Compatible
PRINT Image Matching III:
 Compatible
Dimensions (CIPA compliant):
 
Approx. 117.3 mm × 66.6 mm ×
 
41.3 mm (4 5/8 inches ×
 
2 5/8 inches × 1 11/16 inches)
 (W/H/D)
Mass (CIPA compliant):
 
Approx. 314 g (11.1 oz)
 
(including battery and “Memory
 
Stick PRO Duo” media)
 
Approx. 255 g (9.0 oz)
 (camera 
only)
Operating temperature: 0°C to 40°C
 
(32°F to 104°F)
File format:
 
Still image: JPEG (DCF Ver. 2.0,
 
Exif Ver. 2.3, MPF Baseline)
 
compliant, DPOF compatible
 
3D still images: MPO (MPF
 
Extended (Disparity Image))
 compliant
 
Movie (AVCHD format): AVCHD
 
format Ver. 2.0 compatible
 Video: 
MPEG-4 
AVC/H.264
 
Audio: Dolby Digital 2ch
 
Dolby Digital Stereo Creator
 
•  Manufactured under license from  
Dolby Laboratories.
 
Movie (MP4 format):
 Video: 
MPEG-4 
AVC/H.264
 
Audio: MPEG-4 AAC-LC 2ch
USB communication: Hi-Speed USB
 (USB 
2.0)
[Flash]
Flash guide number: GN 6 (in meters at
 ISO 
100)
Recycling time: Approx. 3 seconds
Flash coverage: Covering 16 mm lens
 
(focal length that the lens indicates)
Flash compensation: ±2.0 EV (1/3 EV
step)
AC Adaptor AC-UB10/
UB10B
Power requirements: AC 100 V to
 
240 V, 50 Hz/60 Hz, 70 mA
Output voltage: DC 5 V, 0.5 A
Operating temperature: 0 °C to 40 °C
 
(32 °F to 104 °F)
Storage temperature: –20 °C to +60 °C
 
(–4 °F to +140 °F)
Dimensions:
Approx. 50 mm × 22 mm × 54 mm
 
(2 inches × 7/8 inches ×
 
2 1/4 inches) (W/H/D)
Mass:
 
For the USA and Canada: Approx.
 
48 g (1.7 oz)
 
For countries or regions other than
 
the USA and Canada: Approx. 43 g
 (1.5 
oz)
Rechargeable battery pack
NP-FW50
Used battery: Lithium-ion battery
Maximum voltage: DC 8.4 V
Nominal voltage: DC 7.2 V
Maximum charge voltage: DC 8.4 V
Maximum charge current: 1.02 A
Capacity: Typical 7.7 Wh (1 080 mAh)
 
Minimum 7.3 Wh (1 020 mAh)
Maximum dimensions:
 
Approx. 31.8 × 18.5 × 45 mm
 
(1 5/16 × 3/4 × 1 13/16 inches)
 (W/H/D)
Mass: Approx. 57 g (2.1 oz)
Design and specifications are subject to change 
without notice.
Model information table
Model
NEX-F3D
NEX-F3K
NEX-F3Y
Destination
AEP, E, KR
US, CND, AEP, E, BR, KR, 
AUS, CH, JE, J
AEP, E, KR, AUS, J
Lens
E16 mm F2.8 / 
E18 – 55 mm F3.5-5.6 OSS
E18 – 55 mm F3.5-5.6 OSS
E18 – 55 mm F3.5-5.6 OSS / 
E55 – 210 mm F4.5-6.3 OSS
• Abbreviation
 AUS 
Australian 
model
 BR : 
Brazilian 
model
 CH : 
Chinese 
model
 CND 
Canadian 
model
 J  : 
Japanese 
model
 JE  : 
Tourist 
model
 KR : 
Korea 
model
本体
[形式]
カメラタイプ:レンズ交換式デジタルカ
 
メラ
使用レンズ:
E
マウントレンズ
[撮像部]
イメージセンサー:
23.5 
×
 15.6 mm
 
APS-C
サイズ)、
CMOS
イメージセ
 
ンサー
総画素数:約
16 500 000
画素
カメラ有効画素数:約
16 100 000
画素
[アンチダスト]
システム:帯電防止コートおよび超音波
 
振動によるアンチダスト機能
[オートフォーカス]
形式:コントラスト検出方式
検出輝度範囲:
EV0 
 EV20
ISO 100
 
当、
F2.8
レンズ使用時)
[露出制御]
測光方式:イメージセンサーによる
 1 
200
分割測光
測光範囲:
EV0 
 EV20
ISO 100
相当、
 F2.8
レンズ使用時)
ISO
感度(推奨露光指数):
 
静止画撮影時:
AUTO
ISO200 
 16000
 
動画撮影時:
AUTO
ISO200 
 3200
相当
露出補正:±
3.0EV
1/3
段ステップ)
[シャッター]
形式:電子制御式縦走りフォーカルプ
 
レーンシャッター
シャッタースピード範囲:
 
静止画撮影時:
1/4000-30
(1/3
 
ステップ
)
、バルブ
 
動画撮影時:
1/4000-1/4
秒、
AUTO
 
時は
1/30
秒まで
 (1/3
段ステップ
)
フラッシュ同調速度:
1/160
[記録メディア]
“メモリースティック
 PRO 
デュオ”、
SD
カード
[液晶モニター]
形式:
7.5 cm
3.0
型)
TFT
駆動
ドット数:
921 600
640
×
RGB
)×
 480
)ドット
[入出力端子]
USB
端子:マイクロ
USB
タイプ
B
HDMI
端子:
HDMI
タイプ
C
ミニ端子
[電源]
バッテリー:リチャージャブルバッテ
 
リーパック
NP-FW50
[その他]
Exif Print
:対応
PRINT Image Matching III
:対応
外形寸法(
CIPA
準拠):
 
117.3
×
66.6
×
41.3 mm
(幅×高
 
さ×奥行き)
本体質量(
CIPA
準拠):
 
314 g
(バッテリー、“メモリース
 
ティック
 PRO 
デュオ”を含む)
 
255 g
(本体のみ)
動作温度:
0
℃∼
 40
記録方式:
 
静止画記録方式:
 JPEG
DCF Ver.2.0
Exif Ver.2.3
 MPF 
Baseline
)準拠、
DPOF
対応
 3D
静止画記録方式:
MPO
MPF
 Extended
(立体視))準拠
 
動画記録方式(
AVCHD
方式):
 AVCHD
規格
 Ver.2.0
準拠
 
映像:
MPEG-4 AVC/H.264
 
音声:
Dolby Digital 2ch
 
ドルビーデジタルステレオクリエー
 
ター搭載
 
 
ドルビーラボラトリーズからの実施権に基づき
製造されています。
 
動画記録方式(
MP4
方式):
 
映像:
MPEG-4 AVC/H.264
 
音声:
MPEG-4 AAC-LC 2ch
USB
通信:
Hi-Speed USB
USB2.0
[ フラッシュ]
ガイドナンバー:
6
ISO100
m
充電時間:約
3
照射角:
16mm
レンズをカバー(レンズ
 
表記の焦点距離)
調光補正:±
2.0EV
1/3
段ステップ)
ACアダプター AC-UB10/
UB10B
定格入力:
AC 100 V 
 240 V
 
50 Hz/60 Hz
70 mA
定格出力:
DC 5 V
0.5 A
動作温度:
℃∼
 40 
保存温度:−
20 
℃∼
 +60 
外形寸法:約
50 mm
×
22 mm
×
54 mm
 
(幅×高さ×奥行き)
本体質量:約
48 g
リチャージャブルバッテリー
パックNP-FW50
使用電池:リチウムイオン蓄電池
最大電圧:
DC 8.4 V
公称電圧:
DC 7.2V
容量:公称容量
 7.7 Wh
1 080 mAh
定格(最小)容量:
7.3 Wh
1 020 mAh
最大外形寸法:約
31.8
×
18.5
×
45 mm
 
(幅×高さ×奥行き)
本体質量:約
57 g
本機や付属品の仕様および外観は、改良のため予告
なく変更することがありますが、ご了承ください。
NEX-F3D/F3K/F3Y_L2
– 3 –
SAFETY-RELATED  COMPONENT  WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH 
MARK 
0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST 
ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPO-
NENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS 
SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY 
SONY. 
ATTENTION AU  COMPOSANT  AYANT  RAPPORT 
À  LA  SÉCURITÉ!
LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES 
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT 
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE REM-
PLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY DONT 
LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU DANS LES 
SUPPLÉMENTS PUBLIÉS PAR SONY.
Caution
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Caution
電池の交換は,正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は,取扱指示に従って処分してください。
CHEMICALS
Some chemicals used for servicing are highly volatile.
Their evaporation caused by improper management affects your health 
and environment, and wastes resources.
Manage the chemicals carefully as follows.
•  Store chemicals sealed in a specific place to prevent from exposure 
to high temperature or direct sunlight.
•  Avoid dividing chemicals into excessive numbers of small containers 
to reduce natural evaporation.
•  Keep containers sealed to avoid natural evaporation when chemicals 
are not in use.
•  Avoid using chemicals as much as possible. When using chemicals, 
divide only required amount to a small plate from the container and 
use up it.
EXTERIOR  PARTS
Be careful to the following points for plastic parts used in this unit.
•  Use a piece of cleaning paper or cleaning cloth for cleaning plastic 
parts. Avoid using chemicals.
 
Even if you have to use chemicals to clean heavy dirt, don’t use paint 
thinner, ketone, nor alcohol.
•  Insert the specific screws vertically to the part when installing a 
plastic part.
 
Be careful not to tighten screws too much.
SAFETY  CHECK-OUT
After correcting the original service problem, perform the following 
safety checks before releasing the set to the customer.
各種薬品の取り扱いについて
現在使用されている薬品の中には揮発性の高い薬品もありま
す。
それらを不用意に取り扱い蒸発させてしまうと,環境や健康へ
影響を与えたり,資源の無駄使いになります。
各種薬品は,下記の点に注意して取り扱ってください。
・ 
保管場所を定め,高温になったり直射日光の当たらない場
所に密閉して保管してください。
・ 
小分け(ハンドラップ等)する数は必要最小限に留め,容器
による自然蒸発を防いでください。
・ 
作業に使用しない時は,必ずキャップ等をして自然蒸発を
防いでください。
・ 
薬品を使用する回数を極力少なくし,使用する場合は使用
する量だけ容器より出して受け皿に残さないようにしてく
ださい。
樹脂系部品の取り扱いについて
本機に使用されている樹脂系の部品は,下記の点に注意して取
り扱ってください。
・ 
清掃には薬品を使用せず,清掃紙や清掃布を使用してくだ
さい。
 
やむを得ず汚れがひどくて薬品を使用する場合は,シン
ナー,ケトン,エーテルは使用しないでください。
・ 
各部品の取り付けには指定されたねじを使用し,部品に対
して垂直に取り付けてください。
 
また,ねじを締め付ける時は,無理な力を加えないでくだ
さい。
サービス,点検時には次のことにご注意ください。
– ENGLISH –
– JAPANESE –
1.  Check the area of your repair for unsoldered or poorly-soldered 
connections. Check the entire board surface for solder splashes and 
bridges.
2.  Check the interboard wiring to ensure that no wires are “pinched” 
or contact high-wattage resistors.
3.  Look for unauthorized replacement parts, particularly transistors, 
that were installed during a previous repair. Point them out to the 
customer and recommend their replacement.
4.  Look for parts which, through functioning, show obvious signs of 
deterioration. Point them out to the customer and recommend their 
replacement.
5.  Check the B+ voltage to see it is at the values specified.
6.  Flexible Circuit Board Repairing
 
•   Keep the temperature of the soldering iron around 350°C during 
repairing.
 
•   Do not touch the soldering iron on the same conductor of the circuit 
board (within 3 times).
 
•   Be careful not to apply force on the conductor when soldering or 
unsoldering.
UNLEADED  SOLDER
This unit uses unleaded solder. 
Boards requiring use of unleaded solder are printed with the lead free 
mark (LF) indicating the solder contains no lead.
(Caution:  Some printed circuit boards may not come printed with the 
lead free mark due to their particular size.)
: LEAD FREE MARK
Be careful to the following points to solder or unsolder.
•  Set the soldering iron tip temperature to 350°C approximately.
 
If cannot control temperature, solder/unsolder at high temperature 
for a short time.
 
Caution: The printed pattern (copper foil) may peel away if the 
heated tip is applied for too long, so be careful!
 
 
Unleaded solder is more viscous (sticky, less prone to 
flow) than ordinary solder so use caution not to let solder 
bridges occur such as on IC pins, etc.
•  Be sure to control soldering iron tips used for unleaded solder and 
those for leaded solder so they are managed separately. Mixing 
unleaded solder and leaded solder will cause detachment phenom-
enon.
1.  注意事項をお守りください。
 
サービスのとき特に注意を要する個所については,キャビ
ネット,シャーシ,部品などにラベルや捺印で注意事項を
表示しています。これらの注意書きおよび取扱説明書等の
注意事項を必ずお守りください。
2.  指定部品のご使用を
 
セットの部品は難燃性や耐電圧など安全上の特性を持った
ものとなっています。従って交換部品は,使用されていた
ものと同じ特性の部品を使用してください。特に回路図,
部品表に0印で指定されている安全上重要な部品は必ず指
定のものをご使用ください。
3.  部品の取付けや配線の引きまわしはもとどおりに
 
安全上,チューブやテープなどの絶縁材料を使用したり,
プリント基板から浮かして取付けた部品があります。また
内部配線は引きまわしやクランパによって発熱部品や高圧
部品に接近しないよう配慮されていますので,これらは必
ずもとどおりにしてください。
4.  サービス後は安全点検を
 
サービスのために取外したネジ,部品,配線がもとどおり
になっているか,またサービスした個所の周辺を劣化させ
てしまったところがないかなどを点検し,安全性が確保さ
れていることを確認してください。
5.  チップ部品交換時の注意
 
・  取外した部品は再使用しないでください。
 
・  タンタルコンデンサのマイナス側は熱に弱いため交換時
は注意してください。
6.  フレキシブルプリント基板の取扱いについて
 
・  こて先温度を約350℃に設定して行ってください。
 
・  同一パターンに何度もこて先を当てないでください。
 
  (3回以内)
 
・  パターンに力が加わらないよう注意してください。
無鉛半田について
本機には無鉛半田が使用されています。
無鉛半田を使用している基板には,無鉛(Lead Free)を意味する
レッドフリーマークがプリントされています。
(注意: 基板サイズによっては,無鉛半田を使用していても
レッドフリーマークがプリントされていないものがあ
ります)
:レッドフリーマーク
無鉛半田は,下記の点に注意して使用してください。
・ 
半田こてのこて先温度は約350℃に設定してください。
 
温度調節が無理な場合は,高温短時間で作業を行ってくだ
さい。
 
注意: 半 田 こ て を 長 く 当 て す ぎ る と, 基 板 の パ タ ー
ン(銅箔)がはがれてしまうことがありますので,注
意してください。また,従来の半田よりも粘性が強
いため,IC端子などが半田ブリッジしないように注
意してください。
・ 
半田こてのこて先は,必ず無鉛半田用と有鉛半田用に分け
て管理してください。
 
無鉛半田と有鉛半田が混在すると剥離現象が発生してしま
います。
NEX-F3D/F3K/F3Y_L2
1-1
1. SERVICE  NOTE
1-1.  PRECAUTION ON REPLACING THE SY-307 BOARD
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
1-2.  ADDITION OF DESTINATION DATA FILE
If the Destination Data file included in the Adjust manual is old, “DESTINATION DATA WRITE” cannot be executed in some cases.
In that case, download a new Destination Data file from the TISS homepage according to the following procedure.
Note 1:  To perform Destination Data Write for this model, the Adjust manual of the DSC-WX50 series must have been installed.
 
Install the Adjust manual of the DSC-WX50 series in advance.
Note 2:  The actual image may differ from the image shown above.
1)  If the Destination Data file in the Adjust manual in use is old, the window shown in Fig. 1 is displayed.
 
Click the [OK] button.
 Fig. 
1
2)  The Destination Data Write window opens.
 
Check the version of the Destination Data file retained in the Adjust manual.
Destination Ver. window
– ENGLISH –
3)  Search the model whose new Destination Data file you want to get on the TISS homepage.
 
When the Destination Data file has been updated, a file with a name “Destination File For ‘model name’.zip” is registered.
(Example) Destination File For DSC-WX50.zip
Furthermore, the version supported by the Destination Data file is shown in the Remarks column.
Note : If the Destination Data file has not been updated, contact the Service Headquarters.
 4)  Download the Destination Data file of the relevant model and unzip the file.
5)  Execute “DESTINATION DATA WRITE” in the Adjust tab of the Adjust manual.
 
Click the [START] button.
Page of 18
Display

Sony NEX-F3D / NEX-F3K / NEX-F3Y Service Manual ▷ Download

  • DOWNLOAD Sony NEX-F3D / NEX-F3K / NEX-F3Y Service Manual ↓ Size: 5.12 MB | Pages: 18 in PDF or view online for FREE
  • Here you can View online or download the Service Manual for the Sony NEX-F3D / NEX-F3K / NEX-F3Y in PDF for free, which will help you to disassemble, recover, fix and repair Sony NEX-F3D / NEX-F3K / NEX-F3Y Digital Camera. Information contained in Sony NEX-F3D / NEX-F3K / NEX-F3Y Service Manual (repair manual) includes:
  • Disassembly, troubleshooting, maintenance, adjustment, installation and setup instructions.
  • Schematics, Circuit, Wiring and Block diagrams.
  • Printed wiring boards (PWB) and printed circuit boards (PCB).
  • Exploded View and Parts List.