Sony NEX-5T / NEX-5TL / NEX-5TY (serv.man2) Service Manual ▷ View online
NEX-5T/5TL/5TY_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
ASSEMBLY
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the
• -XX, -X mean standardized parts, so they may have some differences from the
original one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not
supplied.
• Due to standardization, replacements in the parts list may be different from the
parts specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u: μ, for example:
uA...:
In each case, u: μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark 0 or dotted line
with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque 0 sont
Les composants identifiés par une marque 0 sont
critiques pour la sécurité.
Ne les remplacer que par une pièce portant le nu-
méro spécifié.
Ne les remplacer que par une pièce portant le nu-
méro spécifié.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instruc-
tions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instruc-
tions.
注意
如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
(JAPANESE)
【使用上の注意】
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付い
ている部品と異なる場合があります。
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合があります。
• *印の部品は常備在庫しておりません。
• *印の部品は常備在庫しておりません。
• 抵抗の単位Ωは省略してあります。
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμA..., μPA..., μPB...,
金 被:金属被膜抵抗。
サンキン:酸化金属被膜抵抗。
• インダクタの単位でuHはμHを示します。
• 半導体の名称でuA..., uPA..., uPB..., uPC..., uPD...等はそれぞれμA..., μPA..., μPB...,
μPC..., μPD...を示します。
0印の部品,または0印付の点線で囲まれた部品は,
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
安全性を維持するために,重要な部品です。
従って交換時は,必ず指定の部品を使用してください。
注意
電池の交換は,正しく行わないと破裂する恐れがあり
ます。
電池を交換する場合には必ず同じ型名の電池又は同等
品と交換してください。
使用済み電池は,取扱指示に従って処分してください。
ます。
電池を交換する場合には必ず同じ型名の電池又は同等
品と交換してください。
使用済み電池は,取扱指示に従って処分してください。
• 外装部品色表示
例:
(SILVER) :セットの色を表す。
(Silver) :部品の色を表す。
• Abbreviation
AUS :
AUS :
Australian
model
CH : Chinese model
CND : Canadian model
J
CND : Canadian model
J
: Japanese model
JE
: Tourist model
KR : Korea model
RU : Russian model
RU : Russian model
View Position
Right View
Left View
Top View
Back View
Front View
Bottom View
q;
BT Frame Block
• CN-1001 Board
• BT-2001 Flexible Board
• FP-2045 Flexible Board
• RL-1021 Flexible Board
• BT-2001 Flexible Board
• FP-2045 Flexible Board
• RL-1021 Flexible Board
5
AN-1001 Board
1
Top Cabinet Assy
4
Main Frame Block
• LC-1003 Board
• LC-1001 Flexible Board
• LC-1001 Flexible Board
3
Control Switch Block
2
Rear Cabinet Assy
6
SY-1025 Board
9
Jack Cover Base Block
• IS-104 Board
• IS-075 Flexible Board
• IS-076 Flexible Board
• IS-075 Flexible Board
• IS-076 Flexible Board
qs
Imager Unit
qd
Shutter Charge Assy
7
Top Ground Plate
8
Shoe Nut Plate
qa
Tripod Screw
qf
Front Cabinet Assy
NEX-5T/5TL/5TY_L2
2-2
– JAPANESE –
– ENGLISH –
作業時の注意
フレキシブル基板の導電面に汚れやごみなどがないことを確認してください。
フレキシブル基板の導電面を素手で触れないようにしてください。
フレキシブル基板は,コネクターの奥までまっすぐに差し込んでください。 (図1,図2,図3 参照)
フレキシブル基板の導電面を素手で触れないようにしてください。
フレキシブル基板は,コネクターの奥までまっすぐに差し込んでください。 (図1,図2,図3 参照)
OK
(奥までまっすぐに差し込んである)
NG
(斜めに差し込んである)
NG
(差し込み不十分)
コネクター
コネクター
フレキシブル
基板
基準線
フレキシブル
基板
コネクター
コネクター
基準線
フレキシブル
基板
フレキシブル
基板
コネクター
コネクター
基準線
フレキシブル
基板
フレキシブル
基板
図1
図2
図3
コネクターの開閉部を開ける際,A方向に開け過ぎないようにし
てください。
てください。
コネクターの開閉部を閉じる際,フレキシブル基板を矢印B方向
に押しながら,開閉部を均一に押してください。
に押しながら,開閉部を均一に押してください。
開閉部
コネクター
フレキシブル基板
A
A
開閉部
絶縁面
コネクター
フレキシブル基板
B
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認してください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
先端の剥がれたメッキ部はカットして
除去してください。
(メッキ破片がコネクター内に残って
いる場合もあるので注意してください)
除去してください。
(メッキ破片がコネクター内に残って
いる場合もあるので注意してください)
• コネクターを取り外す際に,線材部(極細)を持って引っ張る
と断線する恐れがありますので,絶対に線材部(極細)を持っ
て引っ張らないでください。
て引っ張らないでください。
• 線材部(極細)を押さえながらコネクターを差し込むと,線材
部(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
には負担をかけないでください。
⾗᧚
G
: Grease
G-85 (J-6082-626-A)
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
and completely)
NG
(The flexible board was plugged in
crooked.)
crooked.)
NG
(The flexible board was not plugged in
completely.)
completely.)
Flexible
Board
Flexible
Board
Board
Connector
Connector
Reference line
Flexible
Board
Board
Connector
Connector
Flexible
Board
Reference line
Connector
Connector
Flexible
Board
Board
Flexible
Board
Reference line
Fig. 1
Fig. 2
Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
a flexible board in direction B.
Holder
Connector
Flexible Board
A
A
Holder
Insulation side
Connector
Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
broken.
SUBSIDIARY MATERIALS
G
: Grease
G-85 (J-6082-626-A)
NEX-5T/5TL/5TY_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. TOP/REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-186-543-01
PLATE, LOGO (BLACK)
1
4-186-543-11
PLATE, LOGO (SILVER)
1
4-186-543-71
PLATE, LOGO (WHITE)
2
X-2587-952-1 CABINET (TOP) ASSY (BLACK) (BLACK)
2
X-2587-953-1 CABINET (TOP) ASSY (SILVER) (SILVER)
2
X-2587-954-1 CABINET (TOP) ASSY (WHITE) (WHITE)
3
1-489-775-21
SWITCH BLOCK, CONTROL (SILVER, WHITE)
3
1-489-775-41
SWITCH BLOCK, CONTROL (BLACK)
4
4-292-152-01
SPRING, BT LID OPEN
5
4-292-161-01
SHAFT, BT LID
6
X-2585-571-1 LID ASSY (BLACK), BT (BLACK)
6
X-2585-572-1 LID ASSY (SILVER), BT (SILVER)
6
X-2585-573-1 LID ASSY (WHITE), BT (WHITE)
7
4-440-299-01
LIGHT (MS), GUIDE,
8
X-2585-568-2 CABINET (REAR) ASSY (BLACK) (BLACK)
8
X-2585-569-2 CABINET (REAR) ASSY (SILVER) (SILVER)
8
X-2585-570-2 CABINET (REAR) ASSY (WHITE) (WHITE)
#76
2-666-551-11 SCREW,
TAPPING,
P2
#200
4-178-124-11
SPECIAL (M1.4 (D2.75)) (Note 1)
#202
4-178-124-31
SPECIAL (M1.4 (D2.75)) (Note 1)
#280
4-437-538-11
SPECIAL (M1.4 (D2.75)) (Note 1)
DISASSEMBLY
1. Remove in numerical order (
1
to
3
) in the left figure.
1-1
1-2
#76
#280
#202
#202
#200
#202
#202
Bottom View
Top View
Right View
1
Open the BT Lid (
1
-1
) → #76 X 2 → #280/#202 X 1 → Open the Shoe Lid (
1
-2
) → #200/#202 X 1
Note
Screw
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
#200 or #280 (Black)
#202 (Silver)
BLACK
SILVER/WHITE
#76: M1.7 X 4.0 (Tapping)
(Silver)
2-666-551-11
2-666-551-11
4.0
1.7
3.8
1.4
(
Black
)
4-178-124-11
#200:
M1.4 X 3.8
2
#200/#202 X 1 → Open the HDMI Lid (
2
-1
) → #200/#202 X 1 → Open the BT Lid (
2
-2
) → #200/#202 X 3
→ Open the LCD (
2
-3
)
2-2
2-1
#200
#202
#202
#200
#202
#202
#200
#202
#202
#200
#202
#202
Bottom View
Left View
Right View
3.8
1.4
(
Silver
)
4-178-124-31
#202:
M1.4 X 3.8
(Claws)
(Claws)
(Claw)
(Claws)
(Bosses)
#200
#202
(Note 1)
#202
(Note 1)
#200
#202
(Note 1)
#202
(Note 1)
#200
#202
(Note 1)
#202
(Note 1)
#280
#202
(Note 1)
#202
(Note 1)
#200
#202
(Note 1)
#202
(Note 1)
#76
#200
#202
(Note 1)
#202
(Note 1)
1
2
2
8
3
3
LCD Section
(See page 2-4)
4
5
6
1-2
2-1
2-3
1-1
2-2
2-2
7
1
When installing,
adjust this position.
adjust this position.
When open the LCD,
be careful these sensors.
be careful these sensors.
#280: M1.4 X 4.5
(Black)
4-437-538-11
4-437-538-11
4.5
1.4
NEX-5T/5TL/5TY_L2
2-4
2-1-2. LCD SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
) in the left figure.
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
4-479-271-01
LC LIGHT INTERCEPT SHEET (765)
52
A-1896-184-A LC-1003 BOARD, COMPLETE
53
4-443-005-01
SHEET, LC FLEXIBLE SLIDER
54
1-886-396-11
LC-1001 FLEXIBLE BOARD (Note 2)
55
4-479-272-01
MF RADIATION SHEET (765)
56
4-440-305-01
HOLDER (G), LC HINGE
57
X-2585-576-1 BRACKET ASSY (G), STRAP
58
4-440-312-01
INSULATING SHEET, LC
59
X-2585-574-1 FRAME
ASSY
60
X-2585-575-1 BRACKET ASSY (L), STRAP
61
4-440-304-01
HOLDER (L), LC HINGE
62
4-440-287-01
RETAINER, LC FLEXIBLE
63
4-440-298-01
CABINET (REAR), LC
64
4-440-285-01
PLATE, LC CABINET (REAR)
65
1-471-591-11 MAGNET
(ND5.4X5.4X1.4)
66
4-472-309-01
SHEET, FRAME (765)
LCD901 A-1978-120-A LCD BLOCK (SERVICE) (BK) (BLACK)
LCD901 A-1981-127-A LCD BLOCK ASSY (SERVICE) (SI) (SILVER)
LCD901 A-1981-128-A LCD BLOCK ASSY (SERVICE) (WH) (WHITE)
#97
2-662-396-31
SCREW (M1.4), NEW, TRUSTAR, P2
#196
4-178-124-01
SPECIAL (M1.4 (D2.75)) (Note 1)
#201
4-178-124-21
SPECIAL (M1.4 (D2.75)) (Note 1)
#246
3-208-537-51
0+Z M1.4X2 NEW TORASUTA
#246
#246
Bottom View
Top View
1
#246 X 7
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
#196 (Black)
#201 (Silver)
BLACK
SILVER/WHITE
Screw
#97: M1.4 X 2.5
(Black)
2-662-396-31
2-662-396-31
2.5
1.4
2.0
1.4
4-178-124-01
(Black)
#196: M1.4 X 2.0
2.0
1.4
4-178-124-21
(Silver)
#201: M1.4 X 2.0
#246: M1.4 X 2.5
(Red)
3-208-537-51
(Red)
3-208-537-51
2.5
1.4
Note 2: Refer to “Assembly-6: The Method of attachment of LC-1001
Flexible Board.”.
Note 2: “Assembly-6: The Method of attachment of LC-1001 Flexible
Board.” を参照してください。
(Claw)
(Claw)
(Claw)
LCD901
#196
#201
(Note 1)
#201
(Note 1)
#246
#246
#246
#246
ns
#246
#97
#97
#97
1
59
51
53
54
(Note 2)
55
52
56
Main Board Section
(See page 2-5)
57
58
60
61
63
64
65
66
62
ns
The changed portions from
Ver. 1.0 are shown in blue.
Ver. 1.0 are shown in blue.
Ver. 1.1 2013.09
Click on the first or last page to see other NEX-5T / NEX-5TL / NEX-5TY (serv.man2) service manuals if exist.