DOWNLOAD Sony NEX-5T / NEX-5TL / NEX-5TY (serv.man2) Service Manual ↓ Size: 7.65 MB | Pages: 30 in PDF or view online for FREE

Model
NEX-5T NEX-5TL NEX-5TY (serv.man2)
Pages
30
Size
7.65 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera / LEVEL2
File
nex-5t-nex-5tl-nex-5ty-sm2.pdf
Date

Sony NEX-5T / NEX-5TL / NEX-5TY (serv.man2) Service Manual ▷ View online

NEX-5T/5TL/5TY_L2
3-2
3
Install the LC Hinge Holder (L) and LC Flexible
Retainer.
4
Connect the LC-1001 flexible board to the LC-1003
board.
And attach the adhesive part of the LC-1001 Flexible
Board.
Adhesive part
LC Hinge Holder (L) and
LC Flexible Retainer
5
Attach the LC Light Interception Sheet.
LC Light Interception Sheet
Adhesive part
6
Roll the LC-1001 flexible board 2 times in the Main
Frame to the as shown in figure.
And attach the adhesive part of the LC-1001 Flexible
Board.
3-2.  CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
 
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
CCD Cleaning Jig (New)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1.  Put the two cleaning cloths on a tray like below.
 
1
 Souse the one cleaning cloth in ethyl alcohol.
 
2
 Put the other cleaning cloth on a tray as it is dry.
2.  Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
 
* Do not slide the tip from right to left or up and down while dabbing.
3.  Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
 
* Do not slide from right to left or up and down while dabbing.
4.  Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
2
The dry cleaning cloth.
NEX-5T/5TL/5TY_L2
3-3E
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1.  Clean up the tip of CCD cleaning jig.
2.  Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
 
* Do not slide from right to left or up and down while dabbing.
3.  Repeat “3” several times to clean up.
4.  According to the service manual, check if there is dirt on the OLPF.
 OLPF
Cleaning Jig
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
Cut
EE3310
ご注意
今回の修理に伴い、ワイヤレス LAN の
接続設定が初期化されています。
また、MAC アドレスも変更されていま
す。
必要に応じて、接続機器との設定を再度
行ってください。
設定の方法について詳しくは、
「取扱説
明書」をご覧ください。
NOTE
The wireless LAN connection settings have 
been initialized and the MAC address has also 
been modifi ed during this repair.
Make settings again for connection to devices 
as needed.
For details of settings, refer to the Instruction 
Manual. 
Page of 30
Display

Click on the first or last page to see other NEX-5T / NEX-5TL / NEX-5TY (serv.man2) service manuals if exist.