Sony NEX-5N / NEX-5ND / NEX-5NK / NEX-5NY (serv.man2) Service Manual ▷ View online
NEX-5N/5ND/5NK/5NY_L2
1-1
1. SERVICE NOTE
1-1. PRECAUTION ON REPLACING THE SY-292 BOARD
Destination Data
When you replace to the repairing board, the written destination data of repairing board also might be changed to original setting.
USB Serial No.
The set is shipped with a unique ID (USB Serial No.) written in it.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
This ID has not been written in a new board for service, and therefore it must be entered after the board replacement.
1-2. PRECAUTION ON REPLACING THE CABINET FRONT
Perform the following procedures for each of the three washers.
Note: Measure the dimensions before replacement of the Cabinet Front according to procedures (1) to (3).
(1) Remove the Imager Block Assy and the IM Adjust Washers (A, B, C).
(2) Measure the dimensions (A) of the removed IM Adjust Washers.
A
+
B
BA
(3) Measure the distance (B) between the surface of the screw hole where the IM Adjust Washers were set and the surface of the E-Mount.
(4) Likewise, measure the dimensions (B’) of each location where IM Adjust Washers of new Cabinet Front are installed.
(5) Calculate the dimension of (A’) of new IM Adjust Washer by using the formula below, and select the washers.
(4) Likewise, measure the dimensions (B’) of each location where IM Adjust Washers of new Cabinet Front are installed.
(5) Calculate the dimension of (A’) of new IM Adjust Washer by using the formula below, and select the washers.
Dimension
(A+B) before replacement – Dimension (B’) of new Cabinet Front
= Dimension (A’) of IM Adjust Washer after replacement
(6) Assemble the imager, using the selected IM Adjust Washers.
(7) After assembling is completed, perform the test shooting and confirm that no blur is observed in the peripheral area of shot.
(7) After assembling is completed, perform the test shooting and confirm that no blur is observed in the peripheral area of shot.
– ENGLISH –
1-3. ABOUT THE FLASH EXTENDER (NEX-5NY ONLY)
If you attach the flash directly to the camera when using SEL55210 (E 55-210mm F4.5-6.3 OSS), images will be partly shadowed by the lens.
To prevent shadowing, attach the extender.
To prevent shadowing, attach the extender.
Extender
A-1787-305-A
A-1787-305-A
Case, EX
4-199-652-01
4-199-652-01
To attach the extender
(1) Turn the camera off before attaching the extender.
(2) Attach the extender firmly to the camera and tighten the screw.
(3) Attach the flash firmly to the extender and tighten the screw.
Note: Only attach the flash supplied with your camera to the extender.
NEX-5N/5ND/5NK/5NY_L2
1-2E
– JAPANESE –
1-1. SY-292基板交換時の注意
仕向けデータ
補修用基板と交換する時、補修用基板に書かれている仕向けデータは元の設定と違っている場合があります。
USBシリアルNo.
セットは、1台毎に異なる固有のID(USB Serial No.)を書き込んだ後、出荷されています。
新品の補修用基板には、このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
新品の補修用基板には、このIDが書き込まれていないので,基板交換後にIDを入力する必要があります。
1-2. 前キャビネット交換時の注意
以下の手順は3箇所それぞれ行ってください。
注意: 前キャビネットの交換を行う前に、手順(1)から(3)にて交換前の寸法を測定してください。
(1) イメージャ Assy、IM調整ワッシャ (A, B, C)を取り外してください。
(2) 取り外したIM調整ワッシャの寸法(A)を測定してください。
A
+
B
BA
(3) IM調整ワッシャが取り付いていたビス穴端面からE-Mount端面までの寸法(B)を測定してください。
(4) 新品の前キャビネットの各IM調整ワッシャ取り付け部についても同様に寸法(B')を測定してください。
(5) 以下の式より新たに使用するIM調整ワッシャの寸法(A')を算出し、ワッシャの選定を行ってください。
(4) 新品の前キャビネットの各IM調整ワッシャ取り付け部についても同様に寸法(B')を測定してください。
(5) 以下の式より新たに使用するIM調整ワッシャの寸法(A')を算出し、ワッシャの選定を行ってください。
交換前の寸法(A+B) − 新前キャビネットの寸法(B' ) = 交換後のIM調整ワッシャ寸法(A')
(6) 選定したIM調整ワッシャを使用してイメージャを組み付けてください。
(7) 組立完成後、試し撮りを行い周辺ボケ等の不具合が無いことを確認してください。
(7) 組立完成後、試し撮りを行い周辺ボケ等の不具合が無いことを確認してください。
1-3. フラッシュ専用エクステンダーについて(NEX-5NYのみ)
SEL55210(E 55-210mm F4.5-6.3 OSS)を付けてフラッシュ撮影をする場合、本機に直接フラッシュを取り付けるとレンズの影が写っ
てしまうため、エクステンダーを取り付けてからお使いください。
てしまうため、エクステンダーを取り付けてからお使いください。
エクステンダー
A-1787-305-A
A-1787-305-A
EXケース
4-199-652-01
4-199-652-01
取り付け方
(1)本機の電源を「OFF」にしてください。
(2)エクステンダーを本機に最後まで差し込んでからネジを締め、しっかり固定してください。
(2)エクステンダーを本機に最後まで差し込んでからネジを締め、しっかり固定してください。
(3)フラッシュをエクステンダーに最後まで差し込んでからネジを締め、しっかり固定してください。
注意: エクステンダーには本体付属のフラッシュ以外は取り付けないでください。
NEX-5N/5ND/5NK/5NY_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
• Abbreviation
AUS :
AUS :
Australian
model
CH :
Chinese
model
CND :
Canadian
model
J
:
Japanese
model
JE :
Tourist
model
KR :
Korea
model
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “
• -XX, -X mean standardized parts, so they may have some differences from the original one.
• Items marked “
∗” are not stocked since they are seldom required for routine service. Some delay
should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not supplied.
• Due to standardization, replacements in the parts list may be different from the parts specified
• Due to standardization, replacements in the parts list may be different from the parts specified
in the diagrams or the components used on the set.
(JAPANESE)
【使用上の注意】
• -XX, -Xは標準化部品のため, セットに付いている部品と異なる場合があります。
• ∗印の部品は常備在庫しておりません。
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いている部品と
• ∗印の部品は常備在庫しておりません。
• ここに記載されている部品は, 補修用部品であるため, 回路図及びセットに付いている部品と
異なる場合があります。
図面番号で部品を指定するときは基板名
又はブロックを併せて指定してください。
又はブロックを併せて指定してください。
お願い
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver) : Parts Color
• 外装部品色表示
例:
(SILVER) :セットの色を表す。
(Silver) :部品の色を表す。
The components identified by mark 0 or
dotted line with mark 0 are critical for safety.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
le numéro spécifié.
0印の部品,または0印付の点線で囲ま
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
れた部品は,安全性を維持するために,
重要な部品です。
従って交換時は,必ず指定の部品を使用
してください。
When indicating parts by reference number,
please include the board name.
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
ACCESSORIES
ASSEMBLY
1
Cabinet (Top) Assy
8
BT Frame/ RL Block Assy
• CN-474 Board
• BT-074 Flexible Board
• FP-1451 Flexible Board
• RL-113 Flexible Board
• BT-074 Flexible Board
• FP-1451 Flexible Board
• RL-113 Flexible Board
9
Jack Cover Base Block
3
Side Cover
7
SY-292 Board
2
LCD Panel Block
6
Main Frame Block
5
Control Switch Block
(BK75500)
4
Ornamental Plate Assy
qs
Cabinet Front Assy
0
Imager Unit
qa
Shutter Charge Block
NEX-5N/5ND/5NK/5NY_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
修理時の注意
• Make sure that the flat cable and flexible board are not cracked or
bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, do not pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, do not press down at wire of connector.
It is possible that a wire is snapped.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
• フラットケーブルおよびフレキシブル基板の端子面に欠け,折
れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しにならな
いように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると断
線する恐れがありますので,絶対に線材部(極細)を持って引っ
張らないでください。
張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部(極
細)が断線する恐れがありますので,絶対に線材部(極細)には負
担をかけないでください。
担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけな
いでください。
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕