Sony NEX-3NL / NEX-3NY Service Manual ▷ View online
NEX-3NL/3NY_L2
3-2
Assembly-7: Notes on Assembling the Radiation Plate
(SY) (762) and Plate (Front) (762)
Plate (Front) (762)
Cabinet (Front) Assy
Boss of the Cabinet
(Front) Assy
(Front) Assy
Hole of the Plate
(Front) (762)
(Front) (762)
Radiation Plate (SY) (762)
NG
NG
When installing the Plate (Front) (762), push it to the right of
the Cabinet (Front) Assy and secure it with screws.
After the Plate (Front) (762) has been installed, confirm that
the boss of the Cabinet (Front) Assy is positioned at the left
side of the hole of the Plate (Front) (762).
the Cabinet (Front) Assy and secure it with screws.
After the Plate (Front) (762) has been installed, confirm that
the boss of the Cabinet (Front) Assy is positioned at the left
side of the hole of the Plate (Front) (762).
Install the Radiation Plate (SY) (762) straight without shifting
it to the left side.
it to the left side.
Assembly-6:
The Method of attachment of FP-2064
Flexible Board.
Flexible Board.
1
Attach the adhesive part of the FP-2064 Flexible
Board to the Hinge Assy.
Board to the Hinge Assy.
Adhesive part
Hinge Assy
FP-2064 Flexible Board
2
Roll the FP-2064 Flexible Board 3 times in the Hinge
Assy as shown in figure.
And attach the adhesive part of the FP-2064 Flexible
Board.
Assy as shown in figure.
And attach the adhesive part of the FP-2064 Flexible
Board.
3
Roll the FP-2064 Flexible Board half-turn in the Hinge
Assy as shown in figure.
Assy as shown in figure.
4
And attach the adhesive part of the FP-2064 Flexible
Board.
And then fold dotted line parts of the FP-2064 Flexible
Board as shown in figure.
Board.
And then fold dotted line parts of the FP-2064 Flexible
Board as shown in figure.
Adhesive part
Valley fold
NEX-3NL/3NY_L2
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt on the OLPF.
4. According to the service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
NEX-3NL/3NY_L2
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt on the OLPF.
4. According to the service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
NEX-3NL/3NY_L2
3-3E
3-2. CLEANING PROCEDURE OF OLPF
<Preparation for Remedy>
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
If you use the new Jig (J-6082-663-A) below, make sure to clean the CCD Cleaning Jig (Tip) below before using, please.
Note: Protection sheet is for preventing the scratch of a surface on the Jig (Tip).
The protection sheet may be come off the Jig when you take the Jig from a bag, but it is no problem.
<ATTENTION>
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
If you cannot remove dirt with remedy above, cleaning by the following jig are used.
Soak a small amount of EE3310 (Liquid cleaner) after wrapping the cleaning cloth (J-6082-636-A) around the cleaning jig (J-6082-635-A).
<Cleaning Procedure for the OLPF>
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
1. Clean up the tip of CCD cleaning jig.
2. Dab the tip of CCD cleaning jig at the OLPF, and pull up straight.
* Do not slide from right to left or up and down while dabbing.
3. Repeat “3” several times to clean up.
4. According to the service manual, check if there is dirt on the OLPF.
4. According to the service manual, check if there is dirt on the OLPF.
CCD Cleaning Jig (New)
(J-6082-663-A)
(J-6082-663-A)
CCD Cleaning Jig
CCD Cleaning Jig (Tip)
Protection Sheet
<Cleaning Procedure for Tip of CCD Cleaning Jig>
1. Put the two cleaning cloths on a tray like below.
1. Put the two cleaning cloths on a tray like below.
1
Souse the one cleaning cloth in ethyl alcohol.
2
Put the other cleaning cloth on a tray as it is dry.
2. Dab the tip of CCD cleaning jig at the cleaning cloth of 1 5 or 6 times.
* Do not slide the tip from right to left or up and down while dabbing.
3. Dab the tip of CCD cleaning jig at the cleaning cloth of 2 5 or 6 times.
* Do not slide from right to left or up and down while dabbing.
4. Wait until the tip will be dried completely.
1
Souse the cleaning
cloth in ethyl alcohol.
cloth in ethyl alcohol.
2
The dry cleaning cloth.
OLPF
Cleaning Jig
(J-6082-635-A)
(J-6082-635-A)
Cleaning Cloth
(J-6082-636-A)
(J-6082-636-A)
Cut
EE3310
