Sony ILCE-3000K / ILCE-3500J (serv.man2) Service Manual ▷ View online
ILCE-3000K/3500J_L2
2-4
2-1-2. MAIN BOARD SECTION
DISASSEMBLY
1. Remove in numerical order (
1
to
8
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2587-854-1 BASE (MAIN) ASSY (771)
52
4-456-090-01
SPRING (BT DISCHARGE) (762)
53
A-1923-785-A BT-2002 FLEXIBLE BOARD, COMPLETE
54
1-885-294-11
IS-105 FLEXIBLE BOARD
55
1-887-267-11
IS-1006 FLEXIBLE BOARD
* 56
4-471-842-01
PLATE (FRONT) (771)
57
A-1958-136-A SY-1026 BOARD, COMPLETE (SERVICE)
58
X-2587-852-1 BASE (SW) ASSY (771)
* 59
X-2587-855-1 FRAME (MAIN) ASSY (771) (Note 1)
60
4-192-233-01 BD
TRIPOD
61
4-484-056-01
SHEET (SY) (771) (Note 2)
BT901
1-780-858-11
TERMINAL BOARD BATTERY
SP901 1-858-343-71 LOUDSPEAKER
(1.0CM)
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
4
#2 X 1
Back View
#2
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
1
Disengage the flexible harnesses (
1
) → #12 X 3
Harnesses
Claw
Back View
#12
#12
2
Disengage the flexible board (
2
)
Boss
Flexible board
Claws
7
#12 X 2
Back View
#12
#12
#12
SP901
#12
#12
#12
(Note 1)
(Note 2)
Claws
Claw
#2
D
BA
C
E
BT901
A
B
E
A
C
D
B
E
1
59
2
58
3
61
4
57
5
8
54
6
55
56
60
53
52
7
51
ST Section
(See page 2-5)
2
1
DISCHARGING OF THE CHARGING CAPACITOR
8
Note 1: Refer to “Assembly-1: Notes on Assembling the ST Block”
when assembling.
Note
Note 2: Refer to “Assembly-8: Notes on Assembling the Sheet (SY)
(771)” when assembling.
ILCE-3000K/3500J_L2
2-5
2-1-3. ST SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
to
5
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
1
Pop-up the flash (
1
) → #12 X 1
Screw
Front View
Flash pop-up button
#12
1
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
4-471-841-01
COVER (ST) (771)
102
X-2587-847-1 CABINET (FRONT) ASSY (771)
(3000K)
102
X-2589-636-1 CABINET (FRONT) ASSY (771) (3500J)
103
A-1957-983-A RL-1023 FLEXIBLE BOARD, COMPLETE (Note 2)
104
4-471-840-01
BASE (RL) (771)
105
X-2587-853-1 ST
ASSY
(771)
107
1-490-083-11
FLASH UNIT
108
1-888-083-11
HB-1002 FLEXIBLE BOARD
110
A-1957-984-A ST-1017 FLEXIBLE BOARD, COMPLETE
111
1-969-002-11
HARNESS (SK-1001) (Pink)
112
1-969-004-11
HARNESS (SK-1003) (Orange)
113
1-969-003-11
HARNESS (SK-1002) (White)
114
4-531-185-01
CLIP (MD) (771)
BH001
1-251-928-21
SOCKET, BATTERY (Note 1)
BT001
1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
C901
1-100-936-11
ELECT 85uF 315V
MIC901 1-542-967-11 MICROPHONE
UNIT
#12
3-080-204-21 SCREW,
TAPPING,
P2
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note
Note 1: Replace the battery holder (BH001) together when replac-
ing the lithium battery (BT001) on the RL-1023 board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
and attach new lithium battery next.
Note 2: Refer to “Assembly-2: Notes on Assembling the RL Block”
when assembling.
#12
#12
Bosses
#12
#12
ns
#12
A
A
1
5
101
4
104
114
103
(Note 2)
2
105
110
3
Imager Block Section
(See page 2-6)
1
,
2
-1,
2
-2,
2
-3
: BT001 (lithium battery)
Board on the mount position.
(See page 6-34 of Level 3)
Board on the mount position.
(See page 6-34 of Level 3)
112
(Orange)
111
(Pink)
113
(White)
107
102
108
MIC901
BT001
(Note 1)
(Note 1)
BH001
(Note 1)
(Note 1)
ns
C901
2
#12 X 1 → Disengage the harnesses (
2
-1
) → Push down the flash (
2
-2
) → Disengage the bosses (
2
-3
)
Back View
#12
2
-2
2
-1
2
-3
Bosses
3
#12 X 2
Back View
#12
4
#12 X 2
Back View
#12
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.04
ILCE-3000K/3500J_L2
2-6
2-1-4. IMAGER BLOCK SECTION
ns: not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
A-1954-964-A SERVICE, MECHA DEVICE (1100)
(including CP6001 (CMOS imager) and IS-1007 complete
board) (Note 5)
152
4-430-446-01
SHEET (IS (720)), RADIATION
* 153
Selection Parts IM WASHER (A), ADJUST (Note 2, 3)
* 154
Selection Parts IM WASHER (B), ADJUST (Note 2, 3)
* 155
Selection Parts IM WASHER (C), ADJUST (Note 2, 3)
156
A-1905-698-A MB CHARGE UNIT (762) (Note 4)
157
1-492-255-11
SHUTTER UNIT (H129)
158
A-1932-986-A MB N HOLDER ASSY (SERVICE 762)
* 159
4-186-538-01
SPRING, LENS LOCK
160
X-2586-035-1 MB L LOCK PIN ASSY (762)
161
4-456-086-01
BUTTON, LENS LOCK
* 162
4-185-963-01
MB N PLATE SP (Note 7)
163
4-284-623-01
MB N PLATE (B) 755
164
4-283-999-03
MB N PLATE A (754)
165
4-188-536-01
CAP, BODY (Note 6)
#64
2-666-551-21 SCREW,
TAPPING,
P2
#197
4-185-990-01
MB SCREW, CHARGE UNIT FIXED
#230
4-287-434-01
TAPPING (1.7 (ECOLOGY))
DISASSEMBLY
1. Remove in numerical order (
1
to
2
) in the left figure.
Screw
#64: M1.7 X 5.0 (Tapping)
(Silver)
2-666-551-21
2-666-551-21
5.0
1.7
1
#64 X 3
#64
Back View
2
#230 X 3
#197: M1.6 X 4.5 (Tapping)
4.5
1.6
(Silver)
4-185-990-01
4-185-990-01
#230: M1.7 X 4.0 (Tapping)
(Black)
4-287-434-01
4-287-434-01
4.0
1.7
Note 1: Refer to “Assembly-3: Screw tightening sequence when
assembling the Radiation Plate (IM)” when assembling.
Note 2: The IM adjust washers (A, B, C) differ in thickness.
Make sure to return the removed IM adjust washers to origi-
nal places.
nal places.
When replacing IM adjust washers, refer to “2-2. SELEC-
TION PARTS” on page 2-9.
TION PARTS” on page 2-9.
If the original state cannot be restored due to loss of the
IM adjust washer, for example, replace the Mecha Device
(1100) (Service).
IM adjust washer, for example, replace the Mecha Device
(1100) (Service).
Note 3: Refer to “Assembly-4: IM Adjust Washer (A, B, C) putting
position” when assembling.
Note 4: Refer to “Assembly-5: Screw tightening sequence when
assembling the MB Charge Unit” when assembling.
Note 5: Precautions for Replacement of the Mecha Device
(1100) (Service).
As Mecha Device (1100) (Service) may be damaged by
static electricity from its structure, handle it carefully like for
the MOS IC.
static electricity from its structure, handle it carefully like for
the MOS IC.
In addition, ensure that the receiver is not covered with
dusts nor exposed to strong light.
dusts nor exposed to strong light.
#230
Back View
Note 6: The Mecha Device (1100) (Service) includes a protective
Body Cap.
This part is supplied only with the Mecha Device (1100)
(Service).
(Service).
Note 7: Refer to “Assembly-6: Apply grease on the MB N Plate SP”
when assembling.
Note
152
153
(Note 2, 3)
154
(Note 2, 3)
155
(Note 2, 3)
2
156
(Note 4)
157
163
164
165
(Note 6)
158
159
160
161
1
ns
(Note 1)
Imager Unit Section
(See page 2-7)
151
(including CP6001 (CMOS imager)
and IS-1007 complete board)
(Note 5)
and IS-1007 complete board)
(Note 5)
#64
#64
#230
#197
ns
162
(Note 7)
ILCE-3000K/3500J_L2
2-7
2-1-5. IMAGER UNIT SECTION
ns: not supplied
Ref. No.
Part No.
Description
201
4-281-914-01
IM SPACER (869)
202
4-281-915-01 IM
GS
TAPE
203
1-856-482-11
FILTER BLOCK, OPTICAL (Note)
#191 4-188-735-01 SCREW
(M1.7)
Screw
Note
Note :
J-6082-737-A
Refer to the following statements when replacing the Optical
filter block.
filter block.
Method of Removal
(1) Pour resolvent (alcohol or cleaning agent) between the
(1) Pour resolvent (alcohol or cleaning agent) between the
imager and the IM spacer.
*
*
Wait for that the adhesive power of the IM spacer
weakens.
(2) Remove the IM spacer from the imager.
Method of Attachment
(1) Attach the IM GS tape and the Optical filter block by
(1) Attach the IM GS tape and the Optical filter block by
aligning them with the outer shape of the IM spacer
evenly.
*
evenly.
*
The two-layer side of the Optical filter block is on the
imager side.
(2) Set the Optical filter block in its attachment jig
(J-6082-737-A), with the attached adhesive side of IM
(J-6082-737-A), with the attached adhesive side of IM
spacer facing upward.
(3) Press the imager down into the jig as shown below to
attach it to the Optical filter block.
Imager
Peel off the released paper.
Pour resolvent (alcohol or cleaning agent)
between the imager and the IM spacer.
between the imager and the IM spacer.
The two-layer
side is on the
imager side.
side is on the
imager side.
Mount
Side
Side
Imager
Side
Side
Optical Filter Block
Peel off the
released paper.
released paper.
Peel off the
released paper.
released paper.
Peel off the
released paper.
released paper.
IM GS Tape
IM Spacer
#191: M1.7 X 3.5
(Black)
4-188-735-01
4-188-735-01
3.5
1.7
201
202
203
(Note)
ns
ns
#191
(All mounted parts and IS-1007 complete board are not supplied,
but they are included in Mecha Device (1100) (Service).)
but they are included in Mecha Device (1100) (Service).)
Click on the first or last page to see other ILCE-3000K / ILCE-3500J (serv.man2) service manuals if exist.