Sony ILCE-3000K / ILCE-3500J (serv.man2) Service Manual ▷ View online
ILCE-3000K/3500J_L2
2-2
OPERATION NOTES
Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)
OK
(The flexible board was plugged in straight
and completely)
and completely)
NG
(The flexible board was plugged in
crooked.)
crooked.)
NG
(The flexible board was not plugged in
completely.)
completely.)
Flexible
Board
Flexible
Board
Board
Connector
Connector
Reference line
Flexible
Board
Board
Connector
Connector
Flexible
Board
Reference line
Connector
Connector
Flexible
Board
Board
Flexible
Board
Reference line
Fig. 1
Fig. 2
Fig. 3
When opening the connector's holder in direction A, do not open
it with excessive force.
it with excessive force.
When closing the connector's holder, press it evenly while pushing
a flexible board in direction B.
a flexible board in direction B.
Holder
Connector
Flexible Board
A
A
Holder
Insulation side
Connector
Flexible Board
B
• Make sure that the flat cable and flexible board are not cracked
or bent at the contact end.
• Do not apply excessive force to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
• The proper way to disconnect a connector is to grab the con-
nector instead of the wires. If you pull on the wires, they might
be broken.
be broken.
• The proper way to connect a connector is to grab the connector
instead of the wires. If you push on the wires, they might be
broken.
broken.
DISCHARGING OF THE CHARGING
CAPACITOR (C901)
CAPACITOR (C901)
R:1 k
Ω / 1 W
(Part code: 1-215-869-11)
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
ST-1017 Flexible Board
Discharge lands
Claw
Release the claw holding this part of the Flexible Board
paying attention not to touch the discharge lands on the
back of the Flexible Board.
paying attention not to touch the discharge lands on the
back of the Flexible Board.
Claw
ST-1017 Flexible Board
C901
Be careful not to break the flexible board.
The charging capacitor is charged up to the maximum 315 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
SUBSIDIARY MATERIALS
G
: Grease
G-85 (J-6082-626-A)
ILCE-3000K/3500J_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. OVERALL SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
X-2587-856-1 BASE (JK) ASSY (771)
2
A-1959-442-A MIS-2002 FLEXIBLE BOARD, COMPLETE
3
4-471-845-01
BASE (SHOE) (771)
4
4-471-846-01
PLATE (SHOE) (771)
5
1-489-775-51
SWITCH BLOCK, CONTROL
6
4-484-055-01
SHEET (WS) (771) (Note)
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
DISASSEMBLY
1. Remove in numerical order (
1
to
5
) in the left figure.
1
#2 X 6 → #12 X 1 → Open the JK lid (
1
) → #2 X 3
Bottom View
Left View
Back View
Right View
#2
#2
#2
#12
#2
1
#2
(Note)
#2
#2
#12
Claws
#12
#2
#2
#12
Bosses
5
2
3
5
2
1
4
6
3
4
1
Rear Section
(See page 2-8)
Main Board Section
(See page 2-4)
1
5
#12 X 4
Back View
#12
#12
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note 1: Refer to “Assembly-7: Notes on Assembling the Sheet (WS)
(771)” when assembling.
Note
ILCE-3000K/3500J_L2
2-4
2-1-2. MAIN BOARD SECTION
DISASSEMBLY
1. Remove in numerical order (
1
to
8
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
51
X-2587-854-1 BASE (MAIN) ASSY (771)
52
4-456-090-01
SPRING (BT DISCHARGE) (762)
53
A-1923-785-A BT-2002 FLEXIBLE BOARD, COMPLETE
54
1-885-294-11
IS-105 FLEXIBLE BOARD
55
1-887-267-11
IS-1006 FLEXIBLE BOARD
* 56
4-471-842-01
PLATE (FRONT) (771)
57
A-1958-136-A SY-1026 BOARD, COMPLETE (SERVICE)
58
X-2587-852-1 BASE (SW) ASSY (771)
* 59
X-2587-855-1 FRAME (MAIN) ASSY (771) (Note 1)
60
4-192-233-01 BD
TRIPOD
61
4-484-056-01
SHEET (SY) (771) (Note 2)
BT901
1-780-858-11
TERMINAL BOARD BATTERY
SP901 1-858-343-71 LOUDSPEAKER
(1.0CM)
#2
2-635-562-31 SCREW
(M1.7)
#12
3-080-204-21 SCREW,
TAPPING,
P2
4
#2 X 1
Back View
#2
Screw
#2: M1.7 X 4.0
(Black)
2-635-562-31
2-635-562-31
4.0
1.7
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
1
Disengage the flexible harnesses (
1
) → #12 X 3
Harnesses
Claw
Back View
#12
#12
2
Disengage the flexible board (
2
)
Boss
Flexible board
Claws
7
#12 X 2
Back View
#12
#12
#12
SP901
#12
#12
#12
(Note 1)
(Note 2)
Claws
Claw
#2
D
BA
C
E
BT901
A
B
E
A
C
D
B
E
1
59
2
58
3
61
4
57
5
8
54
6
55
56
60
53
52
7
51
ST Section
(See page 2-5)
2
1
DISCHARGING OF THE CHARGING CAPACITOR
8
Note 1: Refer to “Assembly-1: Notes on Assembling the ST Block”
when assembling.
Note
Note 2: Refer to “Assembly-8: Notes on Assembling the Sheet (SY)
(771)” when assembling.
ILCE-3000K/3500J_L2
2-5
2-1-3. ST SECTION
ns: not supplied
DISASSEMBLY
1. Remove in numerical order (
1
to
5
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇
: Solder
1
Pop-up the flash (
1
) → #12 X 1
Screw
Front View
Flash pop-up button
#12
1
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
4-471-841-01
COVER (ST) (771)
102
X-2587-847-1 CABINET (FRONT) ASSY (771)
(3000K)
102
X-2589-636-1 CABINET (FRONT) ASSY (771) (3500J)
103
A-1957-983-A RL-1023 FLEXIBLE BOARD, COMPLETE (Note 2)
104
4-471-840-01
BASE (RL) (771)
105
X-2587-853-1 ST
ASSY
(771)
107
1-490-083-11
FLASH UNIT
108
1-888-083-11
HB-1002 FLEXIBLE BOARD
110
A-1957-984-A ST-1017 FLEXIBLE BOARD, COMPLETE
111
1-969-002-11
HARNESS (SK-1001) (Pink)
112
1-969-004-11
HARNESS (SK-1003) (Orange)
113
1-969-003-11
HARNESS (SK-1002) (White)
114
4-531-185-01
CLIP (MD) (771)
BH001
1-251-928-21
SOCKET, BATTERY (Note 1)
BT001
1-756-134-15
BATTERY, LITHIUM (SECONDARY) (Note 1)
C901
1-100-936-11
ELECT 85uF 315V
MIC901 1-542-967-11 MICROPHONE
UNIT
#12
3-080-204-21 SCREW,
TAPPING,
P2
#12: M1.7 X 5.0 (Tapping)
(Black)
3-080-204-21
3-080-204-21
1.7
5.0
Note
Note 1: Replace the battery holder (BH001) together when replac-
ing the lithium battery (BT001) on the RL-1023 board.
(The battery holder removed once cannot be used again.)
When mounting these parts, mount new battery holder first
and attach new lithium battery next.
and attach new lithium battery next.
Note 2: Refer to “Assembly-2: Notes on Assembling the RL Block”
when assembling.
#12
#12
Bosses
#12
#12
ns
#12
A
A
1
5
101
4
104
114
103
(Note 2)
2
105
110
3
Imager Block Section
(See page 2-6)
1
,
2
-1,
2
-2,
2
-3
: BT001 (lithium battery)
Board on the mount position.
(See page 6-34 of Level 3)
Board on the mount position.
(See page 6-34 of Level 3)
112
(Orange)
111
(Pink)
113
(White)
107
102
108
MIC901
BT001
(Note 1)
(Note 1)
BH001
(Note 1)
(Note 1)
ns
C901
2
#12 X 1 → Disengage the harnesses (
2
-1
) → Push down the flash (
2
-2
) → Disengage the bosses (
2
-3
)
Back View
#12
2
-2
2
-1
2
-3
Bosses
3
#12 X 2
Back View
#12
4
#12 X 2
Back View
#12
The changed portions from
Ver. 1.1 are shown in blue.
Ver. 1.1 are shown in blue.
Ver. 1.2 2014.04
Click on the first or last page to see other ILCE-3000K / ILCE-3500J (serv.man2) service manuals if exist.