DOWNLOAD Sony ILCE-3000K / ILCE-3500J (serv.man2) Service Manual ↓ Size: 6.66 MB | Pages: 16 in PDF or view online for FREE

ILCE-3000K/3500J_L2

1-2E

6)  Click the [File Update] button in the window.
 

 

7)  A file selection screen opens. Select the Destination Data file to be added and click the [Open] button.
 

 

8)  When the file has been successfully added, the following window opens.
 

 

9)  Check the Destination Ver. window and confirm that the version has been updated.

 

Destination Ver. window

ILCE-3000K/3500J_L2

2-1

Follow the disassembly in the numerical order given.

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the 

original one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not 

supplied.

•  Due to standardization, replacements in the parts list may be different from the 

parts specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: μ, for example:
 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

The components identified by mark 0 or dotted line 

with mark 0 are critical for safety.

Replace only with part number specified.
Les composants identifiés par une marque 0 sont 

注意

如果电池更换不当会有爆炸危险。
只能用同样类型或等效类型的电池来更换。
务必按照说明处置用完的电池。

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

• Abbreviation
 AUS : 

Australian 

model

 BR  : 

Brazilian 

model

  CH 

: Chinese model

  CND  : Canadian model
 

IND : 

Indian 

model

 JE  : 

Tourist 

model

  KR 

: Korea model

 RU  : 

Russian 

model

Right View

Left View

Front View

Bottom View

Top View

Back View

• LC-1012 Flexible Board

• BT-2002 Flexible Board

• IS-1007 Board

• MIS-2002 Flexible Board

• HB-1002 Flexible Board
• ST-1017 Flexible Board

• RL-1023 Flexible Board

The changed portions from
Ver. 1.2 are shown in blue.

ILCE-3000K/3500J_L2

2-2

Make sure that the conductive side of a flexible board does not have any stain or foreign materials.
Do not touch the conductive side of flexible boards with bare hands.
Plug in a flexible board straight, fully into the connector until it reaches the end inside. (Fig. 1, Fig. 2, Fig. 3)

OK 

(The flexible board was plugged in straight 
and completely)

NG 

(The flexible board was plugged in 
crooked.)

NG 

(The flexible board was not plugged in 
completely.)

Flexible

Board

Flexible
Board

Connector

Connector

Reference line

Flexible
Board

Connector

Connector

Flexible

Board

Reference line

Connector

Connector

Flexible
Board

Flexible

Board

Reference line

Fig. 1

Fig. 2

Fig. 3

When opening the connector's holder in direction A, do not open 
it with excessive force.

When closing the connector's holder, press it evenly while pushing 
a flexible board in direction B.

Holder

Connector

Flexible Board

A

A

Holder

Insulation side

Connector

Flexible Board

B

•  Make sure that the flat cable and flexible board are not cracked 

or bent at the contact end.

•  Do not apply excessive force to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

•  The proper way to disconnect a connector is to grab the con-

nector instead of the wires.  If you pull on the wires, they might 
be broken.

•  The proper way to connect a connector is to grab the connector 

instead of the wires.  If you push on the wires, they might be 
broken.

R:1 k

Ω / 1 W

(Part code: 1-215-869-11)

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.

(Part code: 1-215-869-11)

ST-1017 Flexible Board

Discharge lands

Claw

Release the claw holding this part of the Flexible Board
paying attention not to touch the discharge lands on the
back of the Flexible Board.

Claw

ST-1017 Flexible Board

C901

Be careful not to break the flexible board.

The charging capacitor is charged up to the maximum 315 V 
potential.
There is a danger of electric shock by this high voltage when the 
capacitor is handled by hand.  The electric shock is caused by the 
charged voltage which is kept without discharging when the main 
power of the unit is simply turned off.  Therefore, the remaining 
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of 
a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.

1 k

Ω/1 W

Wrap insulating tape.

1 k

Ω/1 W

Wrap insulating tape.

G

: Grease

G-85 (J-6082-626-A)

ILCE-3000K/3500J_L2

2-3

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  1 

X-2587-856-1  BASE (JK) ASSY (771) 

  2 

A-1959-442-A  MIS-2002 FLEXIBLE BOARD, COMPLETE 

  3 

4-471-845-01 

BASE (SHOE) (771) 

  4 

4-471-846-01 

PLATE (SHOE) (771) 

  5 

1-489-775-51 

SWITCH BLOCK, CONTROL

  6 

4-484-055-01 

SHEET (WS) (771) (Note)

 #2 

2-635-562-31  SCREW 

(M1.7) 

 #12 

3-080-204-21  SCREW, 

TAPPING, 

P2 

1.  Remove in numerical order (

1

 to 

5

) in the left figure.

1

1

Bottom View

Left View

Back View

Right View

#2

#2

#2

#12

#2

1

5

3

2

4

1

1

5

Back View

#12

#12

#2: M1.7 X 4.0

(Black)
2-635-562-31

4.0

1.7

#12: M1.7 X 5.0 (Tapping)

(Black)
3-080-204-21

1.7

5.0