Sony DSC-WX70 (serv.man2) Service Manual ▷ View online
DSC-WX70_L2
2-5
2-1-3. MAIN SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1. Remove to numerical order (
1
to
3
) in the left figure.
2. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
(Note 3)
(Note 2)
SY
-331
2
SP901
109
110
116
119
108
107
104
102
105
106
112
113
114
115
120
103
101
3
117
(Claw)
BT001
BT901
: BT001 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-15 of Level 3)
Board on the mount position.
(See page 6-15 of Level 3)
1
Lens Block Section
118
121
(See page 2-6)
(Note 1)
2
Note
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Focus Lens
Very weak
Optical Stepping Motor
Very weak
Ornamental Ring
Sensor
Flexible
Board
Board
Flexible
Board
Board
Caution :
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。
4-412-626-01
4-412-626-11
4-412-626-21
4-412-626-31
4-412-626-41
4-412-626-11
4-412-626-21
4-412-626-31
4-412-626-41
4-412-626-51
4-412-626-61
4-412-626-71
4-412-626-81
4-412-626-91
4-412-626-61
4-412-626-71
4-412-626-81
4-412-626-91
Note 2 : There are two types of this part, with TransferJet logo
or without TransferJet logo. When replacing this part,
be careful whether a LOGO is existed or not.
be careful whether a LOGO is existed or not.
TransferJet logo
TransferJetのロゴ
この部品にはロゴ付きとロゴ無し2種類の
タイプがあります。
交換時にはロゴの有無に注意してください。
タイプがあります。
交換時にはロゴの有無に注意してください。
Note 2 :
4-412-626-01
4-412-626-11
4-412-626-21
4-412-626-31
4-412-626-41
4-412-626-11
4-412-626-21
4-412-626-31
4-412-626-41
4-412-626-51
4-412-626-61
4-412-626-71
4-412-626-81
4-412-626-91
4-412-626-61
4-412-626-71
4-412-626-81
4-412-626-91
Note 3: Refer to “Assembly-1: Precaution During Speaker
Installation.”.
Note 3: “Assembly-1: Precaution During Speaker Installa-
tion.” を参照してください。
101
4-412-626-01
LID (250), BT (SILVER:US, CH, J) (Note 2)
101
4-412-626-11
LID (250), BT (BLACK:US, CH, J) (Note 2)
101
4-412-626-21
LID (250), BT (PINK:US, CH, J) (Note 2)
101
4-412-626-31
LID (250), BT (VIOLET:US, CH, J) (Note 2)
101
4-412-626-41
LID (250), BT (WHITE:US, CH, J) (Note 2)
101
4-412-626-51
LID (250), BT (SILVER:EXCEPT US, CH, J) (Note 2)
101
4-412-626-61
LID (250), BT (BLACK:EXCEPT US, CH, J) (Note 2)
101
4-412-626-71
LID (250), BT (PINK:EXCEPT US, CH, J) (Note 2)
101
4-412-626-81
LID (250), BT (VIOLET:EXCEPT US, CH, J) (Note 2)
101
4-412-626-91
LID (250), BT (WHITE:EXCEPT US, CH, J) (Note 2)
102
4-417-810-01
LID (150), SHAFT (BT)
103
4-411-642-01
LOCK TSUMAMI (150), BT LID
104
4-411-643-01
LID (150), PLATE (BT)
105
4-266-405-01
SPRING (770), BT LID OPEN
106
4-411-646-01
PLATE (SP) (150)
107
4-411-644-01
PLATE, USB (150)
108
X-2583-248-1 BTH (150) SILVER ASSY (BLACK, SILVER, VIOLET, WHITE)
108
X-2583-249-1 BTH (150) PINK ASSY (PINK)
109
4-266-382-01
SHEET, BT TERMINAL (770)
110
1-883-820-11
BT-068 FLEXIBLE BOARD
112
4-270-063-01
COVER J (770)
113
4-266-365-01
SHEET METAL (J) (770)
114
4-270-064-01
SHEET, J SPACER (770)
115
4-297-557-01
SHEET (760), J
116
4-411-645-01
PLATE (H) (150)
117
A-1860-791-A SY-331 BOARD, COMPLETE (SERVICE)
118
4-273-437-01
FLEXIBLE (770), SHEET LENS
119
4-296-021-01
SHEET (760), ELECTROSTATIC LENS
120
4-418-107-01 GASKET
(USB)
121
4-422-939-01
FLEXIBLE (250), SHEET LENS
BT001
1-756-813-11
LITHIUM RECHARGEABLE BATTERY
*BT901 1-780-826-11
TERMINAL BOARD, BATTERY
SP901
1-858-302-61
LOUDSPEAKER (0.8CM) (Note 3)
2
Remove the Plate (SP) (150) (
2
)
Ver. 1.3 2012.05
DSC-WX70_L2
2-6
2-1-4. LENS BLOCK SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1. The meaning of the sign in left figure is as follows. Be careful when it removes.
◇-X
: Solder
DISASSEMBLY
151
(Note 1, 2)
167
152
ns
ns
ns
ns
ns
ns
ns
ns
#176
#30
#30
#30
#30
#30
#30
(including CD-811 flexible complete
board, CP001 (CMOS imager))
(Note 3, 4)
board, CP001 (CMOS imager))
(Note 3, 4)
#30
ns
ns
ns
ns
ns
153
159
161165
164
160
163
166
162
154
155
156
157
158
Note
Note 2: Refer to the following each item when you exchange parts of
Lens Block
•
1-7.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING
METHOD (page 1-10)
METHOD (page 1-10)
•
1-8.
OPTICAL STEPPING MOTOR (F1430) REPLACING
METHOD (page 1-10)
METHOD (page 1-10)
•
1-9.
DC MOTOR WORM (A) ASSY REPLACING METHOD
(page 1-11)
(page 1-11)
•
1-10.
TWO TUBE LUBRICATING BLOCK ASSY AND
GROUP 1 FRAME REPLACING METHOD (page 1-12)
GROUP 1 FRAME REPLACING METHOD (page 1-12)
• 1-11. FINAL INSPECTION (page 1-16)
Note 3: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level3 when changing the imager.
Note 3: イメージャの交換時はLevel3の6-1ページ、 イメージャ交換時
の注意 を必ずお読みください。
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Focus Lens
Very weak
Optical Stepping Motor
Very weak
Ornamental Ring
Sensor
Flexible
Board
Board
Flexible
Board
Board
Screw
#30: M1.2 X 3.5 (Tapping)
(White)
3-086-156-11
3-086-156-11
3.5
1.2
#176: M1.2 X 2.0
(Silver)
3-947-504-31
3-947-504-31
2.0
1.2
Note 2: レンズブロックの各部品を交換する際は,下記の各項目を参
照してください。
•
1-7.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING
METHOD (page 1-10)
METHOD (page 1-10)
•
1-8.
OPTICAL STEPPING MOTOR (F1430) REPLACING
METHOD (page 1-10)
METHOD (page 1-10)
•
1-9.
DC MOTOR WORM (A) ASSY REPLACING METHOD
(page 1-11)
(page 1-11)
•
1-10.
TWO TUBE LUBRICATING BLOCK ASSY AND
GROUP 1 FRAME REPLACING METHOD (page 1-12)
GROUP 1 FRAME REPLACING METHOD (page 1-12)
• 1-11. FINAL INSPECTION (page 1-16)
ns : not supplied
Note 4: STATIONARY TUBE and REAR MIRROR PLATE are supplied
with the ASM FILTER BLOCK ASSY (SERVICE).
These two parts are used to protect the ASM FILTER BLOCK
ASSY (SERVICE).
ASSY (SERVICE).
Remove these two parts when replacing the ASM FILTER
BLOCK ASSY (SERVICE).
BLOCK ASSY (SERVICE).
Note 4: ASM FILTER BLOCK ASSY (SERVICE)にはSTATIONARY
TUBEとREAR MIRROR PLATEが付属されています。
これらはASM FILTER BLOCK ASSY (SERVICE)を保護する
ための梱包材です。
ための梱包材です。
ASM FILTER BLOCK ASSY (SERVICE)交換時は、この2つ
を取り外して使ってください。
を取り外して使ってください。
151
8-848-872-01
LSV-1430A-DS (BLACK, SILVER) (Note 1, 2)
151
8-848-872-31
LSV-1430A-PK (PINK) (Note 1, 2)
151
8-848-872-41
LSV-1430A-PP (VIOLET) (Note 1, 2)
151
8-848-872-51
LSV-1430A-LS (WHITE) (Note 1, 2)
152
A-1799-459-A TUBE BLOCK ASSY, CAM (BLACK, SILVER)
152
A-1800-103-A TUBE BLOCK ASSY, CAM (PINK)
152
A-1800-104-A TUBE BLOCK ASSY, CAM (VIOLET)
152
A-1836-366-A TUBE BLOCK ASSY, CAM (WHITE)
153
A-1799-617-A LUBRICATING
BLOCK
ASSY,
TUBE
154
4-260-057-02
SHIELD RING (D)
155
4-187-707-01
RING (A), ORNAMENTAL (WHITE)
155
4-187-707-11
RING (A), ORNAMENTAL (VIOLET)
155
4-187-707-21
RING (A), ORNAMENTAL (PINK)
155
4-208-725-11
RING A (Y), ORNAMENTAL (BLACK, SILVER)
156
4-147-109-01 TAPE,
BARRIER
157
A-1836-375-A BARRIER BLOCK ASSY (WHITE)
157
A-1799-629-A BARRIER BLOCK ASSY (BLACK, SILVER)
157
A-1800-675-A BARRIER BLOCK ASSY (PINK)
157
A-1800-676-A BARRIER BLOCK ASSY (VIOLET)
158
4-187-670-01
FRAME, GROUP 1
159
1-787-994-11
STEPPING MOTOR, OPTICAL (F1430)
160
A-1799-444-A WORM (A) BLOCK ASSY, DC MOTOR
161
A-1799-619-A LUBRICATING BLOCK ASSY, GEAR
162
A-1799-625-A LUBRICATING BLOCK ASSY, (A)
163
A-1799-624-A LUBRICATING BLOCK ASSY, (B)
164
A-1799-623-A LUBRICATING BLOCK ASSY, (C)
165
A-1799-622-A LUBRICATING BLOCK ASSY, (D)
166
A-1799-618-A LUBRICATING
BLOCK
ASSY,
TUBE
167
A-1825-023-A FILTER BLOCK ASSY, ASM (SERVICE) (including CD-811
flexible complete board, CP001 (CMOS imager)) (Note 3, 4)
#30
3-086-156-11 SCREW
B1.2
#176
3-947-504-31 SCREW (M1.2)
Ver. 1.1 2012.01
DSC-WX70_L2
2-7E
ACCESSORIES
901
902
903
904
905
906
907
908
This item is supplied with the unit as an accessory, but is not prepared as a service part.
951
Ref. No. Part No.
Description
Remark
951
(Not supplied) Rechargeable battery pack (NP-BN)
Note: This unit has no bundled CD-ROM.
Contents included in the CD-ROM will be supplied to customers as
follows.
Contents included in the CD-ROM will be supplied to customers as
follows.
・ User Guide (HTML)
- You can access to the URL of support site described in the In-
struction Manual.
- All of the contents in the User Guide are included in the Instruction
Manual or built-in guide.
・ Application Software
- By connecting this unit and Windows PC with the USB cable, the
application software [PlayMemories Home Lite version] can be
installed on the PC from the unit.
installed on the PC from the unit.
- In case of using the extended version, install “Expanded Feature”
via Internet.
Ref. No. Part No.
Description
901
1-489-282-11
AC Adaptor AC-UB10/UB10B (J)
901
1-489-282-21
AC Adaptor AC-UB10/UB10B (US, CND)
901
1-489-282-31
AC Adaptor AC-UB10/UB10B (CH)
901
1-489-282-61
AC Adaptor AC-UB10/UB10B
(EXCEPT US, CND, CH, J)
902
1-837-421-11
Power cord (mains lead) ( EA, HK)
902
1-837-424-11
Power cord (mains lead) (TW)
902
1-837-427-11
Power cord (mains lead) (AEP, E (EXCEPT Saudi))
902
1-837-428-11
Power cord (mains lead) (KR)
904
1-569-008-33
Conversion (2P) Adaptor (E: NTSC)
905
1-839-666-11
Micro USB cable (USB)
906
2-050-981-01
Wrist strap (Gray) (PINK, SILVER, WHITE)
906
2-050-981-11
Wrist strap (Black) (BLACK, VIOLET)
907
2-888-952-01
Paint pen (Black) (BLACK, VIOLET)
907
2-888-952-11
Paint pen (Gray) (PINK, SILVER, WHITE)
908
4-415-356-01
Instruction Manual (JAPANESE)
908
4-415-356-11
Instruction Manual (SIMPLIFIED CHINESE)
908
4-415-357-11
Instruction Manual (ENGLISH)
* 908
4-415-357-21
Instruction Manual (ENGLISH, SPANISH)
* 908
4-415-357-31
Instruction Manual (ENGLISH, FRENCH)
* 908
4-415-357-41
Instruction Manual (ENGLISH, RUSSIAN, UKRAINIAN)
* 908
4-415-357-51
Instruction Manual (ENGLISH, FRENCH, ITALIAN,
SPANISH, PORTUGUESE, GERMAN, DUTCH,
TURKISH, GREEK, POLISH, CZECH, HUNGARIAN,
SLOVAK, SWEDISH, FINNISH, NORWEGIAN,
DANISH, CROATIAN, ROMANIAN)
* 908
4-415-357-61
Instruction Manual (ENGLISH, TRADITIONAL
CHINESE, SIMPLIFIED CHINESE, MALAY,
INDONESIAN,
THAI,
ARABIC,
PERSIAN)
Ref. No. Part No.
Description
* 908
4-415-357-71 Instruction Manual
(ENGLISH, SPANISH, PORTUGUESE)
* 908
4-415-357-81
Instruction Manual (ENGLISH, TRADITIONAL
CHINESE, SIMPLIFIED CHINESE, INDONESIAN,
ARABIC,
PERSIAN)
* 908
4-415-357-91
Instruction Manual (ENGLISH, SPANISH,
PORTUGUESE,
TRADITIONAL
CHINESE,
SIMPLIFIED CHINESE, KOREAN)
* 908
4-415-358-11
Instruction Manual (ENGLISH, TRADITIONAL
CHINESE, SIMPLIFIED CHINESE)
908
4-415-358-21
Instruction Manual (KOREAN)
* 908
4-415-358-31
Instruction Manual (SPANISH, PORTUGUESE)
* 908
4-415-358-41 Instruction Manual
(ENGLISH,
TRADITIONAL
CHINESE)
* 908
4-415-358-51
Instruction Manual (ENGLISH, ARABIC, PERSIAN)
Ver. 1.3 2012.05
DSC-WX70_L2
3-1E
3. ASSEMBLY
Assembly-1: Precaution During Speaker Installation.
Speaker
Harness
Harness
Rib
Route the speaker harness as shown below.
Assembly-2: Precaution During of ST-284 Flexible Board.
Install the ST-284 flexible board.
ST-284 flexible board
Claws
Bosses
Assembly-3: Attaching Method of LCD and TP Block Assy.
Attach the LCD Cushion (760) to LCD.
Attach the LCD to the TP Block Assy.
Remove the released paper of the LCD Cusion (760).
Peel off the LCD cushion (760) from pasted board.
LCD Cushion (760)
LCD Cushion (760)
Released Paper of
the LCD Cushion (760)
the LCD Cushion (760)
LCD
TP Block Assy
Align shape of LCD.
Do not place the TP flexible board between
the LCD and the TP block assy.
the LCD and the TP block assy.