Sony DSC-WX7 (serv.man2) Service Manual ▷ View online
DSC-WX7_L2
1-14E
1-11-2. Inspection When Cam Tube Block Assy Or Straight Tube Lubricated Assy Is Replaced
Focus check
1
1
Preparation
• Camera installed re-assemble lens.
• Chart (Printed PDF file at the same magnification) (Refer to <Reference>)
•
Tripod
• Mirror (ex. CD)
•
Memory
card
•
PC
2
Shoot setting
(1) Paste the chart.
• Chart should be on the flat wall.
• Illuminance level in the chart should be the same.
• Make the tripod’s height and the center of the chart to the same height.
• Enough space needed for shooting.
(2) Set the camera.
• Set [P] mode
• Set [Maximum] size
• Set ISO lowest level
• Set Steady Shot [OFF]
• Set Flash [OFF]
(3) Set the camera on a tripod.
(4) Adjust the position of the camera and the chart.
1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
* The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
* Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
Remove the mirror.
3
Shooting
(1) Set [Self-Timer]
(2) Shot
4
(2) Shot
4
Check the shot image.
(1) Check the shot image on PC.
100% Display (Display at the same magnification of its Pixel.)
Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
<Reference>
• How to Print the Chart
Print “Forcus-Chart_A3.pdf” with printer.
Print at the same magnification (It means 100 % size).
Check the settings of printer to print in proper size.
• Check of chart size.
Make charts together and check if the size of charts is the following size.
* The chart consists of 2 pcs.
• How to Print the Chart
Print “Forcus-Chart_A3.pdf” with printer.
Print at the same magnification (It means 100 % size).
Check the settings of printer to print in proper size.
• Check of chart size.
Make charts together and check if the size of charts is the following size.
* The chart consists of 2 pcs.
DSC-WX7_L2
2-1
2. REPAIR PARTS LIST
Follow the disassembly in the numerical order given.
IDENTIFYING PARTS
Link
ACCESSORIES
DISCHARGING OF THE CHARGING CAPACITOR
ASSEMBLY
SY
-276
3
LCD Module
q;
Main Frame Assy
qd
Lens Block Section
• CD-811 Flexible Board
qg
BTH Block Assy
5
Front Block Assy
1
Rear Block Assy
qa
Upper Block Assy
qs
ST-246 Flexible Board
qf
SY-276 Board
2
Control Switch Block (SW61770)
9
SW-571 Flexible Board
4
Side Cabinet (L)
8
Side Cabinet (G)
6
Cover Block
Assy
Assy
7
DC Cover
(ENGLISH)
NOTE:
• -XX, -X mean standardized parts, so they may have some differences from the original
• -XX, -X mean standardized parts, so they may have some differences from the original
one.
• Items marked “*” are not stocked since they are seldom required for routine service.
Some delay should be anticipated when ordering these items.
• The mechanical parts with no reference number in the exploded views are not sup-
plied.
• Due to standardization, replacements in the parts list may be different from the parts
specified in the diagrams or the components used on the set.
• CAPACITORS:
uF:
uF:
μF
• COILS
uH:
uH:
μH
• RESISTORS
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
All resistors are in ohms.
METAL: metal-film resistor
METAL OXIDE: Metal Oxide-film resistor
F:
nonflammable
• SEMICONDUCTORS
In each case, u:
In each case, u:
μ, for example:
uA...:
μA... , uPA... , μPA... ,
uPB...
,
μPB... , μPC... , μPC... ,
uPD...,
μPD...
The components identified by mark
0
or dotted line with mark
0 are critical for
safety.
Replace only with part number specified.
Replace only with part number specified.
Les composants identifiés par une marque
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant
le numéro spécifié.
Caution
Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type.
Dispose of used batteries according to
the instructions.
replaced.
Replace only with the same or equivalent
type.
Dispose of used batteries according to
the instructions.
• Color Indication of Appearance Parts
Example:
Example:
(SILVER) : Cabinet’s Color
(Silver)
: Parts Color
• Abbreviation
AR :
AR :
Argentine
model
BR
: Brazilian model
AUS :
Australian
model
CH :
Chinese
model
CND :
Canadian
model
HK
: Hong Kong model
J
: Japanese model
JE :
Tourist
model
KR :
Korea
model
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
View Position
Right View
Left View
Front View
Bottom View
Top View
Back View
DSC-WX7_L2
2-2
– ENGLISH –
– JAPANESE –
NOTE FOR REPAIR
• Make sure that the flat cable and flexible board are not cracked
of bent at the terminal.
Do not insert the cable insufficiently nor crookedly.
• When remove a connector, don’t pull at wire of connector. It is
possible that a wire is snapped.
• When installing a connector, don’t press down at wire of con-
nector.
It is possible that a wire is snapped.
• Do not apply excessive load to the gilded flexible board.
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)
DISCHARGING OF THE CHARGING CAPACITOR (C901)
The charging capacitor is charged up to the maximum 330 V
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
potential.
There is a danger of electric shock by this high voltage when the
capacitor is handled by hand. The electric shock is caused by the
charged voltage which is kept without discharging when the main
power of the unit is simply turned off. Therefore, the remaining
voltage must be discharged as described below.
Preparing the Short Jig
To preparing the short jig, a small clip is attached to each end of
a resistor of 1 k
a resistor of 1 k
Ω /1 W (1-215-869-11).
Wrap insulating tape fully around the leads of the resistor to
prevent electrical shock.
prevent electrical shock.
1 k
Ω/1 W
Wrap insulating tape.
1 k
Ω/1 W
Wrap insulating tape.
ST-246 Flexible
Board
Board
ST-246 Flexible
Board
Board
C901
R:1 k
Ω/1 W
C901
Note: High-voltage cautions
Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.
Short-circuit between two points with
the short jig about 10 seconds.
(Part code: 1-215-869-11)
修理時の注意
• フラットケーブルおよびフレキシブル基板の端子面に欠け,
折れ等がないことを確認する。
また,コネクタへの接続は,差し込み不足や斜め差しになら
ないように注意する。
• コネクタを取り外す時に,線材部(極細)を持って引っ張ると
断線する恐れがありますので,絶対に線材部(極細)を持って
引っ張らないでください。
引っ張らないでください。
• 線材部(極細)を押さえながらコネクタを差し込むと,線材部
(極細)が断線する恐れがありますので,絶対に線材部(極細)
には負担をかけないでください。
• 金メッキされているフレキシブル基板には,強い負担をかけ
ないでください。
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
వ┵ߩ߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
㒰ߒߡߊߛߐޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡࠆ
႐ว߽ࠆߩߢᵈᗧߒߡߊߛߐ㧕
ストロボ用充電コンデンサ(C901)の放電
ストロボ用充電コンデンサは最大330Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ています。
この高電圧で充電されたコンデンサに手を触れた場合,
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず,残留しています。こ
のため,下記の方法で残留電圧を放電してください。
ショート治具の準備
ショート治具は1kΩ/1W抵抗(1-215-869-11)の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
1 k
Ω/1 W
⛘✼࠹ࡊߢᏎߊ
ST-246 Flexible
Board
Board
ST-246 Flexible
Board
Board
C901
R:1 k
Ω/1 W
ㇱຠࠦ࠼㧦1-215-869-11
ࠦࡦ࠺ࡦࠨߩ㔚
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
ࡈ࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ
C901
DSC-WX7_L2
2-3
2-1. EXPLODED VIEWS
2-1-1. REAR SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
1
4-266-465-01
CUSHION (770), LCD (Note 3)
2
4-266-463-01
WINDOW (770), LCD (Note 3)
3
4-266-467-01
SHEET, LCD FLEXIBLE (770)
4
1-489-380-11 SWITCH BLOCK, CONTROL (SW61770) (SLIVER, WHITE)
4
1-489-380-21
SWITCH BLOCK, CONTROL (SW61770) (BLACK)
4
1-489-380-31
SWITCH BLOCK, CONTROL (SW61770) (PINK)
4
1-489-380-41
SWITCH BLOCK, CONTROL (SW61770) (BLUE)
5
A-1807-914-A REAR (770) SILVER BLOCK ASSY
(SILVER: US, UK, CH, J) (Note 2, 4)
5
A-1807-916-A REAR (770) BLACK BLOCK ASSY
(BLACK: US, UK, CH, J) (Note 2, 4)
5
A-1807-917-A REAR (770) PINK BLOCK ASSY
(PINK: US, CH, J) (Note 2, 4)
5
A-1807-919-A REAR (770) BLUE BLOCK ASSY
(BLUE: US, CH, J) (Note 2, 4)
5
A-1807-920-A REAR (770) WHITE BLOCK ASSY
(WHITE: US, UK, CH, J) (Note 2, 4)
5
A-1807-924-A REAR (770) SILVER N BLOCK ASSY
(SILVER: EXCEPT US, UK, CH, J) (Note 2, 4)
5
A-1807-929-A REAR (770) BLACK N BLOCK ASSY
(BLACK: EXCEPT US, UK, CH, J) (Note 2, 4)
5
A-1807-930-A REAR (770) PINK N BLOCK ASSY
(PINK: EXCEPT US, CH, J) (Note 2, 4)
5
A-1807-931-A REAR (770) BLUE N BLOCK ASSY
(BLUE: EXCEPT US, CH, J) (Note 2, 4)
5
A-1807-932-A REAR (770) WHITE N BLOCK ASSY
(WHITE: EXCEPT US, UK, CH, J) (Note 2, 4)
6
4-278-661-01
SHEET SW (770)
LCD901 8-753-373-31 ACX402CMQ-1
#212
4-270-114-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#213
4-270-114-11
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#215
4-270-115-01
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
#216
4-270-115-11
SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)
1. Remove to numerical order (
1
to
3
) in the left figure.
DISASSEMBLY
1
#212/#215 X 4
→ #213/#216 X 2
6
Front/Top Section
(See page 2-4)
3
LCD901
#213
#216
(Note 1)
#216
(Note 1)
#212
#215
(Note 1)
#215
(Note 1)
#212
#215
(Note 1)
#215
(Note 1)
#212
#215
(Note 1)
#215
(Note 1)
2
4
(Claws)
1
(Claw)
2
1
5
(Note 2, 4)
1
(Note 3)
2
(Note 3)
3
#212
#215
#215
#212
#215
#215
#213
#216
#216
Bottom View
Left View
Right View
Screw
Note
Screw's
Ref. No. (Parts Color.)
Ref. No. (Parts Color.)
#212 (Silver)
SILVER/PINK/BLUE/
WHITE
#215 (Black)
BLACK
#213 (Silver)
SILVER/PINK/BLUE/
WHITE
#216 (Black)
BLACK
Cabinet's Color
Table 2-1
Note 1
THE COMBINATION OF CABINET’S
COLOR AND SCREW
COLOR AND SCREW
The screw pointed
is different according to the cabinet's color.
For the combination of cabinet's color and screw, please refer to Table 2-1.
Note 4: Refer to “Assembly-4: Precaution During of Rear
Block Assy Installation.”.
Note 4: “Assembly-4: Precaution During of Rear Block
Assy Installation.”
を参照してください。
Note 3: Refer to “Assembly-3: Attaching Method of LCD
Cushion (770), LCD Window (770)”.
Note 3: “Assembly-3: Attaching Method of LCD Cushion
(770), LCD Window (770)”
を参照してください。
1.4
3.0
#212: M1.4 X 3.0
(Silver)
4-270-114-01
4-270-114-01
1.4
2.0
#213: M1.4 X 2.0
(Silver)
4-270-114-11
4-270-114-11
A-1807-914-A
A-1807-916-A
A-1807-917-A
A-1807-916-A
A-1807-917-A
A-1807-919-A
A-1807-920-A
A-1807-920-A
A-1807-924-A
A-1807-929-A
A-1807-930-A
A-1807-929-A
A-1807-930-A
A-1807-931-A
A-1807-932-A
A-1807-932-A
Note 2 : There are two types of this part, with TransferJet logo
or without TransferJet logo. When replacing this part,
be careful whether a LOGO is existed or not.
be careful whether a LOGO is existed or not.
TransferJet logo
A-1807-914-A
A-1807-916-A
A-1807-917-A
A-1807-916-A
A-1807-917-A
A-1807-919-A
A-1807-920-A
A-1807-920-A
A-1807-924-A
A-1807-929-A
A-1807-930-A
A-1807-929-A
A-1807-930-A
A-1807-931-A
A-1807-932-A
A-1807-932-A
TransferJet
のロゴ
この部品にはロゴ付きとロゴ無し2種類の
タイプがあります。
交換時にはロゴの有無に注意してください。
タイプがあります。
交換時にはロゴの有無に注意してください。
Note 2 :
1.4
3.0
#215: M1.4 X 3.0
(Black)
4-270-115-01
4-270-115-01
1.4
2.0
#216: M1.4 X 2.0
(Black)
4-270-115-11
4-270-115-11
Click on the first or last page to see other DSC-WX7 (serv.man2) service manuals if exist.