Sony DSC-WX5 (serv.man2) Service Manual ▷ View online
DSC-WX5/WX5C_L2
1-9
qf
Rotate the Cam Tube and the lens is retractile.
qg
Lift up the Tube (A) Assy.
qh
Remove the Cam Tube Block.
Objective Side View
Side View
Tube (A) Assy
Tube (A)
Assy
Assy
Cam Tube Block
Cam Tube
Tube (A)
Assy
Assy
Cam Tube
qj
Remove the Tube (A) Assy.
qk
Rotate the Tube B and the lens is drawn out.
ql
Remove the 2-group Frame Assy.
w;
Remove the 2-group Drawing Plate and the 2-group Drawing Spring.
Note: The 2-group Drawing Plate and the 2-group Drawing Spring are not supplied. Please do not lose.
Note: The 2-group Drawing Plate and the 2-group Drawing Spring are not supplied. Please do not lose.
wa
Rotate the Tube B to the position of the sign.
ws
Remove the Cam Tube.
1-group Frame
Assy
Assy
Tube (A) Assy
Tube B
Tube B
2-group
Drawing Spring 2-group
Drawing Spring 2-group
Frame Assy
2-group
Drawing Plate
Drawing Plate
Eyepiece Side View
Objective Side View
Tube B
Sign
Cam Tube
Cam Tube
Cam Tube
Tube (A) Assy
3
Install the 2-group Drawing Spring and the 2-group Drawing Plate on the 2-group Frame Assy.
Note 1: Do not mistake the direction of parts.
Note 2: After of the installation of parts, keep suppressing it by the hand so as not to fall.
Note 1: Do not mistake the direction of parts.
Note 2: After of the installation of parts, keep suppressing it by the hand so as not to fall.
4
Pass the flexible board through the Cam Tube.
5
Match two blades of the Tube B to two ditches of the 2-group Frame Assy.
6
Rotate the Tube B and the lens is retractile.
Tube B
2-group
Drawing Spring
Drawing Spring
2-group
Frame Assy
Frame Assy
2-group Frame Assy
Flexible Board
Convex Side
Rib Side
2-group
Drawing Plate
Drawing Plate
Objective Side View
Blades of
Tube B
Tube B
Blades of Tube B
Cam Tube
Ditches
Keep suppressing it by
the hand so as not to fall.
the hand so as not to fall.
Installation
1
1
Match two blades of the Tube B to two cutting lacks of the Cam Tube and install it.
2
Rotate the Tube B to the position of the sign.
Tube B
Eyepiece Side View
Tube B
Sign
Cam Tube
Cutting Lacks
Cam Tube
Blades
Blades
– ENGLISH –
DSC-WX5/WX5C_L2
1-10
– ENGLISH –
7
Match three ledges of the 1-group Frame Assy to three ditches of the Tube (A) Assy and install it.
8
Match two convex parts of the Tube (A) Assy to two convex parts of the Cam Tube.
9
Match three pins of the 1-group Frame Assy to three ditches of the Cam Tube.
0
Combine the Tube (A) Assy with the edge of the Cam Tube.
qa
Rotate the Cam Tube and the lens is retractile.
1-group
Frame Assy
Frame Assy
1-group
Frame Assy
Frame Assy
Eyepiece Side View
Objective Side View
Objective Side View
Side View
Tube (A) Assy
Tube (A) Assy
Pin of 1-group Frame Assy
(Make the other as match as
two places similar)
(Make the other as match as
two places similar)
Tube (A) Assy
Tube (A)
Assy
Assy
Tube (A) Assy
Tube (A) Assy
Tube (A) Assy
Ledges
Cam Tube Block
Cam Tube
Cam Tube
Cam Tube Block
Ditches
Barrier Lever
Convex Parts
Convex Parts
qs
Match seven convex parts of the Main Assy to seven ditches of the Fixed Tube and install it.
qd
Install the Naruto Gear on the Fixed Tube.
qf
Rotate the Naruto Gear and the lens is drawn out.
qg
Pass the Flexible Board through the hole of the Fixed Tube.
qh
Fix two claws of the Flexible Board into ribs of the Fixed Tube.
qj
Rotate the Naruto Gear and the lens is retractile.
Main Assy
Naruto Gear
Naruto Gear
Eyepiece Side View
Fixed Tube
Fixed Tube
Fixed Tube
Claws
Naruto Gear
Flexible Board
DSC-WX5/WX5C_L2
1-11
– ENGLISH –
qk
Install the Rear Mirror Tube Assy on the Main Assy.
Note: Do not pinch the Flexible Board between the Rear Mirror Tube Assy and the Main Assy.
Note: Do not pinch the Flexible Board between the Rear Mirror Tube Assy and the Main Assy.
ql
Tighten up four screws in order of
1 → 2 → 3 → 4.
*Tightening torque = 0.068 ± 0.01N • m (0.7 ± 0.1kgf • cm)
Rear Mirror Tube Assy
1
3
4
2
w;
Arrange the Flexible Board.
Main Assy
Rib
Rib
Boss
Boss
Boss
Boss
Boss
Adhesive Sheet
Adhesive Sheet
Boss
Connect the Flexible Board
from 2-group Frame Assy.
from 2-group Frame Assy.
Left View
Bottom View
Top View
Right View
Rear View
wd
Hook the Spring.
wf
Stick the Close Hole Tape.
wg
Perform the Flange Back Adjustment after it assembled the Optics Unit.
Close Hole Tape
wa
With four bosses fitted in position, install Zoom Gear Block.
ws
Tighten one screw.
*Tightening torque = 0.068 ± 0.01N • m (0.7 ± 0.1kgf • cm)
*Tightening torque = 0.068 ± 0.01N • m (0.7 ± 0.1kgf • cm)
Front Side
Rear Side
Screw
Zoom Gear Block
Bosses
Spring
Bosses
Tweezers
DSC-WX5/WX5C_L2
1-12E
1-10. FINAL INSPECTION
1-10-1. Confirm There Is No Fault In Actual Motion/Actual Screen
下図は当機種と本体の形状が異なります。
Note:
Note:
As for the figure below, this model and the shape
of the main body are different.
of the main body are different.
Inspect it as follows when you exchange parts in the lens block.
1
1
Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
2
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
3
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
4
Appearance condition Scratches or stains must not be noticeable, except that the customer permits them.
5
Foreign matters on the lens The lens condition must not be worse than that when the camera was received from the customer.
Lens at TELE end
Lens at WIDE end
Upward
Downward
Horizontal
Full stroke check
1-10-2. Inspection When Tube (A) Assy Or Cam Tube Is Replaced
Focus check
1
1
Preparation
• Camera installed re-assemble lens.
• Chart (Printed PDF file at the same magnification) (Refer to <Reference>)
•
Tripod
• Mirror (ex. CD)
•
Memory
card
•
PC
2
Shoot setting
(1) Paste the chart.
• Chart should be on the flat wall.
• Illuminance level in the chart should be the same.
• Make the tripod’s height and the center of the chart to the same height.
• Enough space needed for shooting.
• Illuminance level in the chart should be the same.
• Make the tripod’s height and the center of the chart to the same height.
• Enough space needed for shooting.
(2) Set the camera.
• Set [P] mode
• Set [Maximum] size
• Set ISO lowest level
• Set Steady Shot [OFF]
• Set Flash [OFF]
• Set [Maximum] size
• Set ISO lowest level
• Set Steady Shot [OFF]
• Set Flash [OFF]
(3) Set the camera on a tripod.
(4) Adjust the position of the camera and the chart.
(4) Adjust the position of the camera and the chart.
1. Set the zoom position of the camera at Wide end.
2. Attach the mirror onto the center of the chart.
* The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
* Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
Remove the mirror.
2. Attach the mirror onto the center of the chart.
* The mirror should not tilt on the chart.
3. Set the camera to display the chart on LCD like in the following picture.
4. Adjust the camera position to the center of the chart.
* Adjust the tripod height and the position (Lateral direction).
5. Adjust the camera angle to the frame of the chart with tripod.
Remove the mirror.
3
Shooting
(1) Set [Self-Timer]
(2) Shot
(2) Shot
4
Check the shot image.
(1) Check the shot image on PC.
100% Display (Display at the same magnification of its Pixel.)
Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
100% Display (Display at the same magnification of its Pixel.)
Compare the image with the sample you set.
No extreme focus blurring
It should be distinguished the black and white by the sharpness between them.
If it is in NG level, replace the lens unit.
<Reference>
• How to Print the Chart
• How to Print the Chart
Print “Forcus-Chart_A3.pdf” with printer.
Print at the same magnification (It means 100 % size).
Check the settings of printer to print in proper size.
• Check of chart size.
Make charts together and check if the size of charts is the following size.
* The chart consists of 2 pcs.
Click on the first or last page to see other DSC-WX5 (serv.man2) service manuals if exist.