Sony DSC-WX350 (serv.man2) Service Manual ▷ View online
DSC-WX350
4-5
4-3-3. Front Block Section
• Disassembly order
No.
Part
Item
Note
1
Cabinet (Front) Assy
#212 x 1
Claw x 1
Claw x 1
2
Lithium Holder
Claw x 2
3
Lithium Rechargeable
Battery
Battery
Solder x 1
4
MIC Retainer, MIC
Cushion
Cushion
#276 x 1
This screw cannot be reused. Discard the screw removed once in servicing. Instead,
use a new screw.
use a new screw.
5
ST-1020 Flexible Board
Refer to “Notes on Assembling the ST-1020 Flexible Board” when assembling. (Page
4-6)
4-6)
6
Plate (Rotary Base)
#276 (4)
Cabinet (Upper) Assy
#212 (1)
Claw
Claws
2
3
4
5
6
1
1.4
3.0
#212: M1.4 X 3.0
(Silver)
4-270-114-01
4-270-114-01
#276: M1.4 X 3.0 (Tapping)
(Silver)
3-348-998-41
3-348-998-41
3.0
1.4
DSC-WX350
4-6
4-3-4. Complementary Information
(1) Notes on Assembling the Lens Unit
Hook the flexible board to the claw.
Flexible Board
Claw
(2) Notes on Assembling the Speaker Unit
Route the speaker harnesses as shown below.
Speaker
Harnesses
Harnesses
Ribs
(3) Notes on Assembling the ST-1020 Flexible Board
Install the ST-1020 Flexible Board as shown below.
ST-1020
Flexible Board
Flexible Board
Claw
Claw
Boss
Claw
(4) Notes on Assembling the LCD Unit
Claws
Claws
NG
OK
LCD Unit
LCD Unit
DSC-WX350
4-7
Note on removing the Cabinet (Rear) Assy
Remove the Cabinet (Rear) Assy as shown below to prevent
the hinge of the PLAY button from being deformed.
the hinge of the PLAY button from being deformed.
1. Remove the Wi-Fi side of the Cabinet (Rear) Assy.
Cabinet (Rear) Assy
Hinge part of the
Play Button
Play Button
2. Further lift the Wi-Fi side of the Cabinet (Rear) Assy while press-
ing the control button.
Control Button
3. Confirm that the Cabinet (Rear) Assy has passed over the control
button.
Control Button
4. Finally remove the control button side of the Cabinet (Rear) Assy.
Cabinet (Rear) Assy
DSC-WX350
4-8
4-4. LENS BLOCK
4-4-1. Removal and Installation
(1) Barrier Base Replacing Method
Removal
1. Turn on the power and pull out the lens to set it in the TELE end state.
2. Remove the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Repeat steps 3 and 4, and then remove the Ornamental Ring A.
1. Turn on the power and pull out the lens to set it in the TELE end state.
2. Remove the battery.
3. Pour a solvent such as alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
4. Heat the Ornamental Ring A with a drier.
5. Repeat steps 3 and 4, and then remove the Ornamental Ring A.
Ornamental Ring A
A
Tweezers
Drier
Solvent
6. Release the four claws to detach the Barrier Cover and the two Barrier Blade B, and then release one claw from each Torsion Spring to
detach the two Barrier Blade A.
Barrier Cover
Barrier Blade B
Barrier Blade A
Claws
Claws
Claw
7. Remove the two Torsion Springs and the Switching Ring Spring, and then release the two claws to detach the Barrier Base.
Barrier Base
Switching Ring Spring
Torsion Springs
Claws
Click on the first or last page to see other DSC-WX350 (serv.man2) service manuals if exist.