DOWNLOAD Sony DSC-WX220 Service Manual ↓ Size: 8.08 MB | Pages: 44 in PDF or view online for FREE

Model
DSC-WX220
Pages
44
Size
8.08 MB
Type
PDF
Document
Service Manual
Brand
Device
Digital Camera
File
dsc-wx220.pdf
Date

Sony DSC-WX220 Service Manual ▷ View online

DSC-WX220
4-15
Cam Tube B
Cam Tube B
2 Group Frame
3 Group Assy
Straight Tube Block
Straight Tube
Straight Tube
19. Fully turn the Cam Tube B in the arrow direction.
20. Remove the 2 Group Frame.
21. Remove the Straight Tube Block.
22. Turn the Straight Tube in the arrow direction to detach it from the Cam Tube B.
DSC-WX220
4-16
White Part
Thinnest Groove
Cam Tube B
Cam Tube B
Lever
Cutout
Straight Tube
Straight Tube
3 Group Assy
Straight Tube Block
2 Group Frame
2 Group Frame
Shaft of 3 Group Assy
Top side view
Installation
1. Align the Lever with the cutout as shown in the figure, and then install the Straight Tube to the Cam Tube B.
    Note: Be sure to set the Straight Tube at the correct insertion position.
2. Turn the Straight Tube in the arrow direction to the maximum.
3. Install the Straight Tube Block aligning the thinnest groove with the white part as shown in the figure, and then turn 
    the Cam Tube B in the arrow direction to the maximum.
4. Install the 2 Group Frame at a position where the Shaft of 3 Group Assy is visible through the cutout of the 2 Group Frame.
DSC-WX220
4-17
3 Group Assy
Lever
Lever
1 Frame Assy
Cabinet Number
Flexible Board
Claws
Main Body
Claws
Cam Tube A
Rotary Cam Tube
Semicircular 
Cutout
Gear Edge
Rotary Tube
Stationary Tube Assy
8. Install the Rotary Cam Tube to the Rotary Tube aligning the semicircular cutout with the Gear edge.
9. Install the Stationary Tube Assy at the position shown in the figure as a guideline.
    Note: Be sure to install the Rotary Cam Tube with the semicircular cutout and the Gear edge set in the "OK" state shown in the figure.
10. Install the Main Body so that the Flexible Board position matches the hole to pass the Flexible Board.
5. Install the 1 Frame Assy so the Lever positions match.
    Note: Confirm that the Barrier closes when the 1 Frame Assy is pushed.
6. Set the 3 Group Assy in the groove in the orientation where the Flexible Board comes to the nearly opposite side of the cabinet number 
    on the Cam Tube A.
    Note: Be sure to set the 3 Group Assy at the correct insertion position.
7. Push the 3 Group Assy until the three claws lock.
OK
NG
DSC-WX220
4-18
Fold inside
Draw up
A
Gear A
Gear A
Gear B
Gear Worm
Wheel
Rear Mirror
Plate
Z Retainer
Screws
Screw
Flexible Board
Sensor
LF-139 Flexible Board
Ribs
Rib
Rib
Rib
Boss
Boss
Boss
Boss
11. Turn the Gear in the arrow direction to extend the Mirror Plate slightly.
12. Turn portion A in the arrow direction to TELE end and remove the Flexible Board from the hole in the Stationary Tube Assy.
13. Install the Gear Worm Wheel, Gear A, and Gear B.
14. Install the Rear Mirror Plate.
15. Install four screws and the Z Retainer. Tighten the screws in the order of numbers in the figure below.
16. Install the LF-139 Flexible Board.
1
2
3
4
Page of 44
Display

Click on the first or last page to see other DSC-WX220 service manuals if exist.