Sony DSC-WX200 (serv.man2) Service Manual ▷ View online
DSC-WX200_L2
2-5
2-1-3. MAIN SECTION
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
101
A-1900-219-A HOLDER (570C) BLOCK ASSY, BT (SILVER)
101
A-1900-220-A HOLDER (570D) BLOCK ASSY, BT (BLACK)
101
A-1900-221-A HOLDER (570E) BLOCK ASSY, BT (PINK)
101
A-1900-222-A HOLDER (570F) BLOCK ASSY, BT (GOLD)
102
4-453-470-01
SHEET (570), MS RADIATION
103
4-441-491-01
PLATE (570), STRAP
104
4-419-301-01
TERMINAL, SHEET (BT)
105
1-887-404-11
BT-2004 FLEXIBLE BOARD
106
A-1927-748-A SY-1008 BOARD, COMPLETE (SERVICE)
107
4-419-313-01
FLEXIBLE, SHEET LENS
108
4-441-493-01
PLATE (570), SP
109
4-441-492-01
PLATE (570), HDMI
BT001
1-853-130-11
LITHIUM BATTERY (SECONDARY)
*BT901 1-780-826-11
TERMINAL BOARD, BATTERY
SP901
1-858-343-71
LOUDSPEAKER (1.0CM) (Note 2)
#71
3-208-537-01
0+Z M1.4X2 NEW TORASUTA
1. Remove in numerical order (
1
to
3
) in the left figure.
2. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X
: Solder
DISASSEMBLY
103
102
105
107
106
101
104
BT001
BT901
: BT001 (LITHIUM SECONDARY BATTERY)
Board on the mount position.
(See page 6-14 of Level 3)
Board on the mount position.
(See page 6-14 of Level 3)
Lens Block Section
3
1
2
(See page 2-6)
(Note 1, 3)
109
108
SP901
(Note 2)
(Note 2)
#71
2
SY-100
8
Do not touch the metal
part for Antenna.
part for Antenna.
(Claw)
Note
2
(
2
) SP PLATE (570)
Note 2: Refer to “Assembly-2: Note on Installing the Speaker Instal-
lation.”.
Note 3: Refer to “Assembly-4: Note on Installing the of Lens Block.”.
Note 2: “Assembly-2: Note on Installing the Speaker Installation.” を参
照してください。
Note 3: “Assembly-4: Note on Installing the Lens Block.” を参照して
ください。
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.
注意
電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は、取扱指示に従って処分してください。
電池を交換する場合には必ず同じ型名の電池又は同等品と交換して
ください。
使用済み電池は、取扱指示に従って処分してください。
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Zoom Motor
Very weak
Yoke
Very weak
Yoke
Very weak
Focus Lens
Very weak
3
#71 X 1
#71
Back View
Screw
#71: M1.4 X 2.0
(Red)
3-208-537-01
3-208-537-01
2.0
1.4
DSC-WX200_L2
2-6
2-1-4. LENS BLOCK SECTION
ns : not supplied
Ref. No.
Part No.
Description
Ref. No.
Part No.
Description
151
8-848-888-01
DEVICE, LENS LSV-1510A-DS (SILVER) (Note 1, 2)
151
8-848-888-11
DEVICE, LENS LSV-1510A-BK (BLACK) (Note 1, 2)
151
8-848-888-21
DEVICE, LENS LSV-1510A-GD (GOLD) (Note 1, 2)
151
8-848-888-51
DEVICE, LENS LSV-1510A-DP (PINK) (Note 1, 2)
152
4-294-350-01
RING A, ORNAMENTAL (Y) (SILVER)
152
4-294-350-51
RING A, ORNAMENTAL (Y) (PINK)
152
4-295-917-11
RING A, ORNAMENTAL (T) (BLACK)
152
4-295-917-21
RING A, ORNAMENTAL (T) (GOLD)
153
A-1861-623-A BARRIER ASSY (1510A-DS) (SILVER)
153
A-1861-626-A BARRIER ASSY (1510A-BK) (BLACK)
153
A-1861-629-A BARRIER ASSY (1510A-GD) (GOLD)
153
A-1905-740-A BARRIER
ASSY(1510A-DP)
(PINK)
154
A-1861-259-A GEAR WH LUBRICATED ASSY
155
A-1861-257-A GEAR B LUBRICATED ASSY
156
A-1861-258-A GEAR A LUBRICATED ASSY
157
A-1861-309-A DC MOTOR WORM ASSY
158
X-2582-885-1 LF-139 FLEXIBLE BOARD
159
A-1913-151-A CD-841 FLEXIBLE BOARD, COMPLETE
(including CP001 (CMOS imager)) (Note 3)
160
CAUTION
TAPE,
FPC
161
4-294-347-01 RETAINER,
FG
#176 3-947-504-31 SCREW
(M1.2)
#258 4-299-468-11 SCREW,
TAPPING
UB1.2(CH)
1. The meaning of the symbol in left figure is as follows. Be careful when you remove it.
◇-X
: Solder
DISASSEMBLY
ns
ns
ns
158
156
157
155
154
161
153
152
(Note 1, 2)
159
(including CP001 (CMOS imager))
(Note 3)
(Note 3)
160
(SIZE : 10.1mm X 5.4mm)
151
#258
#258
#258
#176
Note
Note 2: Refer to the following each item when you exchange parts of
Lens Block
•
1-9.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING
METHOD (page 1-11)
METHOD (page 1-11)
•
1-10.
DC MOTOR WORM ASSY REPLACING METHOD
(page 1-11)
(page 1-11)
•
1-11.
THREE TUBE LUBRICATING BLOCK ASSYS AND
GROUP 1 FRAME REPLACING METHOD (page 1-12)
GROUP 1 FRAME REPLACING METHOD (page 1-12)
• 1-12. FINAL INSPECTION (page 1-16)
Note 3: Be sure to read “Precautions for Replacement of Imager” on
page 6-1 of Level 3 when changing the imager.
Note 3: イメージャの交換時はLevel 3の6-1ページ、“イメージャ交換
時の注意”を必ずお読みください。
Note 1:
Hold the Lens Block at the
center of both sides.
Do not hold the following part.
Hold here.
PRECAUTIONS WHEN HOLDING THE LENS BLOCK
Lens Barrier
Very weak
Zoom Motor
Very weak
Zoom Motor
Very weak
Yoke
Very weak
Yoke
Very weak
Focus Lens
Very weak
Screw
#176: M1.2 X 2.0
(Silver)
3-947-504-31
3-947-504-31
2.0
1.2
#258: M1.2 X 3.5 (Tapping)
(Silver)
4-299-468-11
4-299-468-11
1.2
3.5
Note 2: レンズブロックの各部品を交換する際は,下記の各項目を参
照してください。
•
1-9.
ORNAMENTAL RING A OR BARRIER ASSY REPLACING
METHOD (page 1-11)
METHOD (page 1-11)
•
1-10.
DC MOTOR WORM ASSY REPLACING METHOD
(page 1-11)
(page 1-11)
•
1-11.
THREE TUBE LUBRICATING BLOCK ASSYS AND
GROUP 1 FRAME REPLACING METHOD (page 1-12)
GROUP 1 FRAME REPLACING METHOD (page 1-12)
• 1-12. FINAL INSPECTION (page 1-16)
CAUTION
For the part of 160 : TAPE, FPC, cut POLYESTER TAPE (BLACK) 10
MM (9-913-210-03) into the desired length and use it.
MM (9-913-210-03) into the desired length and use it.
注意
160 : TAPE, FPCは、POLYESTER TAPE (BLACK) 10 MM (9-913-210-03)
を切って使用すること。
を切って使用すること。
DSC-WX200_L2
2-7E
ACCESSORIES
901
902
903
904
905
906
907
Ref. No. Part No.
Description
8-022-156-00
Rechargeable battery pack NP-BN/J (J)
8-022-156-33
Rechargeable battery pack NP-BN/UC (CND)
8-022-156-51
Rechargeable battery pack NP-BN/CE (EXCEPT CND, CH, J)
8-022-156-76
Rechargeable battery pack NP-BN/CN (CH)
Ref. No. Part No.
Description
901
1-489-282-12
AC Adaptor AC-UB10/UB10B/UB10C/UB10D (J)
901
1-489-282-21
AC Adaptor AC-UB10/UB10B/UB10C/UB10D (CND)
901
1-489-282-31
AC Adaptor AC-UB10/UB10B/UB10C/UB10D (CH)
901
1-490-498-61
AC Adaptor AC-UB10/UB10B/UB10C/UB10D (EXCEPT
CND, CH, J)
CND, CH, J)
902
1-837-421-11
Power cord (mains lead) (UK, E (Saudi), HK)
902
1-837-422-11
Power cord (mains lead) (JE)
902
1-837-427-11
Power cord (mains lead) (AEP, RU, E (EXCEPT Saudi))
902
1-837-429-11
Power cord (mains lead) (AUS)
903
1-569-007-12
Conversion (2P) Adaptor (JE)
904
1-569-008-12
Conversion (2P) Adaptor (E: NTSC)
905
1-846-615-11
Micro USB cable
906
2-050-981-01
Wrist strap (Gray) (GOLD, PINK, SILVER)
906
2-050-981-11
Wrist strap (Black) (BLACK)
907
4-447-403-01
Instruction Manual (JAPANESE)
907
4-447-403-11
Instruction Manual (SIMPLIFIED CHINESE)
* 907
4-447-404-11
Instruction Manual (ENGLISH)
* 907
4-447-404-31
Instruction Manual (ENGLISH, FRENCH)
* 907
4-447-404-41
Instruction Manual (ENGLISH, RUSSIAN, UKRAINIAN)
* 907
4-447-404-51
Instruction Manual (ENGLISH, FRENCH, ITALIAN,
SPANISH, PORTUGUESE, GERMAN, DUTCH,
GREEK, POLISH, CZECH, HUNGARIAN, SLOVAK,
SWEDISH, FINNISH, NORWEGIAN, DANISH,
CROATIAN, ROMANIAN)
SPANISH, PORTUGUESE, GERMAN, DUTCH,
GREEK, POLISH, CZECH, HUNGARIAN, SLOVAK,
SWEDISH, FINNISH, NORWEGIAN, DANISH,
CROATIAN, ROMANIAN)
* 907
4-447-404-61
Instruction Manual (ENGLISH, TRADITIONAL
CHINESE, SIMPLIFIED CHINESE, MALAY,
INDONESIAN, THAI, TURKISH, ARABIC, PERSIAN)
CHINESE, SIMPLIFIED CHINESE, MALAY,
INDONESIAN, THAI, TURKISH, ARABIC, PERSIAN)
Ref. No. Part No.
Description
* 907
4-447-404-71
Instruction Manual (ENGLISH, SPANISH, BRAZILIAN
PORTUGUESE)
PORTUGUESE)
* 907
4-447-404-91
Instruction Manual (ENGLISH, SPANISH, BRAZILIAN
PORTUGUESE, TRADITIONAL CHINESE, SIMPLIFIED
CHINESE, KOREAN)
PORTUGUESE, TRADITIONAL CHINESE, SIMPLIFIED
CHINESE, KOREAN)
* 907
4-447-405-11
Instruction Manual (ENGLISH, TRADITIONAL
CHINESE, SIMPLIFIED CHINESE)
CHINESE, SIMPLIFIED CHINESE)
* 907
4-447-405-41
Instruction Manual (ENGLISH, ARABIC, PERSIAN)
Note: This unit has no bundled CD-ROM.
Contents included in the CD-ROM will be supplied to customers as
follows.
Contents included in the CD-ROM will be supplied to customers as
follows.
・ User Guide (HTML)
- You can access the URL of the support site described in the
Instruction Manual.
- All of the contents in the User Guide are included in the Instruction
Manual or built-in guide.
・ Application Software
- If a customer requests the CD-ROM, consult with each Head
Quarters.
DSC-WX200_L2
3-1E
3. ASSEMBLY
Assembly-1: Installation Method of Antenna.
Rib
Antenna
Antenna
1 Insert the rib on the left of the antenna into the main
frame hole.
2 Install the antenna in the direction of arrow.
* Check that the metal piece of the antenna is in contact
with the metal part on the SY-1008 board.
with the metal part on the SY-1008 board.
Claw
Claw
Main frame hole
Metal part on
the SY-1008 board
the SY-1008 board
Assembly-2: Note on Installing the Speaker Installation.
Route the speaker harness as shown below.
Speaker
Harness
Harness
Rib
Assembly-3: Note on Installing the ST-1012 Flexible Board.
Install the ST-1012 flexible board.
ST-1012 F
lexible
Board
Bosses
Assembly-4: Note on Installing the Lens Block.
Hook the flexible board to the boss.
Flexible board
Boss
Click on the first or last page to see other DSC-WX200 (serv.man2) service manuals if exist.