DOWNLOAD Sony DSC-WX150 (serv.man2) Service Manual ↓ Size: 5.45 MB | Pages: 21 in PDF or view online for FREE

DSC-WX150_L2

1-9

White Part

Thinnest Groove

Cam Tube B

Cam Tube B

Lever

Cutout

Straight Tube

Straight Tube

3 Group Assy

Straight Tube Block

2 Group Frame

2 Group Frame

Shaft of 3 Group Assy

Top side view

1. Align the Lever with the cutout as shown in the figure, and then install the Straight Tube to the Cam Tube B.
    Note: Be sure to set the Straight Tube at the correct insertion position.
2. Turn the Straight Tube in the arrow direction to the maximum.

3. Install the Straight Tube Block aligning the thinnest groove with the white part as shown in the figure, and then turn 
    the Cam Tube B in the arrow direction to the maximum.

4. Install the 2 Group Frame at a position where the Shaft of 3 Group Assy is visible through the cutout of the 2 Group Frame.

3 Group Assy

Lever

Lever

1 Frame Assy

Cabinet Number

Flexible Board

Claws

Main Body

Claws

Cam Tube A

Rotary Cam Tube

Semicircular 

Cutout

Gear Edge

Rotary Tube

Stationary Tube Assy

8. Install the Rotary Cam Tube to the Rotary Tube aligning the semicircular cutout with the Gear edge.
9. Install the Stationary Tube Assy at the position shown in the figure as a guideline.
    Note: Be sure to install the Rotary Cam Tube with the semicircular cutout and the Gear edge set in the "OK" state shown in the figure.

10. Install the Main Body so that the Flexible Board position matches the hole to pass the Flexible Board.

5. Install the 1 Frame Assy so the Lever positions match.
    Note: Confirm that the Barrier closes when the 1 Frame Assy is pushed.

6. Set the 3 Group Assy in the groove in the orientation where the Flexible Board comes to the nearly opposite side of the cabinet number 
    on the Cam Tube A.
    Note: Be sure to set the 3 Group Assy at the correct insertion position.

7. Push the 3 Group Assy until the three claws lock.

OK

NG

DSC-WX150_L2

1-10

Fold inside

Draw up

Gear A

Gear A

Gear B

Gear Worm

Wheel

Rear Mirror

Plate

Z Retainer

Screws

Screw

Flexible Board

Sensor

LF-139 Flexible Board

Ribs

Rib

Rib

Rib

Boss

Boss

Boss

Boss

11. Turn the Gear in the arrow direction to extend the Mirror Plate slightly.
12. Turn portion A in the arrow direction to TELE end and remove the Flexible Board from the hole in the Stationary Tube Assy.

13. Install the Gear Worm Wheel, Gear A, and Gear B.
14. Install the Rear Mirror Plate.

15. Install four screws and the Z Retainer. Tighten the screws in the order of numbers in the figure below.

16. Install the LF-139 Flexible Board.

1

2

3

4

Connector

Flexible Board

Claws

Sensors

OK

NG

FG Leaf

Spring

FG Leaf Spring

FG Leaf Spring

Claw

FPC Retainer

Flexible Board

FPC Tape

FPC Tape

Rib

Connector

17. Connect the two Flexible Boards to the Connectors on the LF-139 Flexible Board.
18. Stick the FPC Tape as shown in the figure below.

19. Install the two Sensors and attach the FG Leaf Spring.
      Note: Attach the FG Leaf Spring in the correct orientation.
20. Attach the FPC Retainer.

21. Apply a voltage of 2.5 V to the DC Motor and retract the Lens.

DC2.5V

DSC-WX150_L2

1-11E

Note: As for the figure below, this model and the shape

of the main body are different.

Inspect it as follows when you exchange parts in the lens block.

Zoom motion (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
No abnormal sound or motion must be found over full stroke between TELE end and WIDE end.
Zoom image
No abnormality such as a skipped image or wavy image must be found in the image through LCD or finder over full stroke between
TELE end and WIDE end.
Barrier (Check five postures: horizontal, upward/downward, upper/lower oblique 45º)
The barrier must be opened and closed fully, free from a sticking in the midway.
No abnormal sound must be heard during the operation.
Appearance condition Scratches or stains must not be noticeable, except that the customer permits them.
Foreign matters on the lens The lens condition must not be worse than that when the camera was received from the customer.

Lens at TELE end

Lens at WIDE end

Upward

Downward

Horizontal

Full stroke check

1

2

3

4

5

Focus check
1

  Preparation

 

•  Camera installed re-assemble lens.

 

•  Chart (Printed PDF file at the same magnification) (Refer to <Reference>)

 • 

Tripod

 

•  Mirror (ex. CD)

 • 

Memory 

card

 • 

PC

2

  Shoot setting

 

(1)  Paste the chart.

 

•  Chart should be on the flat wall.

 

•  Illuminance level in the chart should be the same.

 

•  Make the tripod’s height and the center of the chart to the same height.

 

•  Enough space needed for shooting.

 

(2)  Set the camera.

 

•  Set [P] mode

 

•  Set [Maximum] size

 

•  Set ISO lowest level

 

•  Set Steady Shot [OFF]

 

•  Set Flash [OFF]

 

(3)  Set the camera on a tripod.

 

(4)  Adjust the position of the camera and the chart.

 

1. Set the zoom position of the camera at Wide end.

 

2. Attach the mirror onto the center of the chart.

 

    * The mirror should not tilt on the chart.

 

3. Set the camera to display the chart on LCD like in the following picture.

 

4. Adjust the camera position to the center of the chart.

 

    * Adjust the tripod height and the position (Lateral direction).

 

5. Adjust the camera angle to the frame of the chart with tripod.

 

    Remove the mirror.

3

  Shooting

      (1)  Set [Self-Timer]
      (2)  Shot
4

  Check the shot image.

      (1)  Check the shot image on PC.
 

100% Display (Display at the same magnification of its Pixel.)

 

Compare the image with the sample you set.

      No extreme focus blurring
      It should be distinguished the black and white by the sharpness between them.
      If it is in NG level, replace the lens unit.

<Reference>
•     How to Print the Chart
      Print “Forcus-Chart_A3.pdf” with printer.
      Print at the same magnification (It means 100 % size).
      Check the settings of printer to print in proper size.
•     Check of chart size.
      Make charts together and check if the size of charts is the following size.
      * The chart consists of 2 pcs.

DSC-WX150_L2

2-1

Follow the disassembly in the numerical order given.

SY

-327

3

 LCD Module

7

 Main Frame Assy

q;

 Lens Block Section

    • CD-841 Flexible Board

qs

 BTH Block Assy 

4

 Front Block Assy 

1

 Rear Block Assy 

8

 Upper Block Assy  

9

 ST-269 Flexible Board

qa

 SY-327 Board

6

 DC Cover

5

 Cover Block

     Assy

2

 Control Switch Block

(SW63150/SW63170)

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original 

one.

•  Items marked “*” are not stocked since they are seldom required for routine service. 

Some delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not sup-

plied.

•  Due to standardization, replacements in the parts list may be different from the parts 

specified in the diagrams or the components used on the set.

• CAPACITORS:
 uF: 

μF

• COILS
 uH: 

μH

• RESISTORS
  All resistors are in ohms.
  METAL: metal-film resistor
  METAL OXIDE: Metal Oxide-film resistor
 F: 

nonflammable

• SEMICONDUCTORS
  In each case, u: μ, for example:
 uA...: 

μA... , uPA... , μPA... ,

 uPB... 

, 

μPB... , μPC... , μPC... ,

 uPD..., 

μPD...

The components identified by mark 0 

or dotted line with mark 0 are critical for 

safety.
Replace only with part number specified.
Les composants identifiés par une marque 
0 sont critiques pour la sécurité.

Ne les remplacer que par une pièce portant 
le numéro spécifié.

Danger of explosion if battery is incorrectly
replaced.
Replace only with the same or equivalent
type.
Dispose of used batteries according to
the instructions.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver)  : Parts Color

• Abbreviation
  CH 

: Chinese model

  CND  : Canadian model
  KR 

: Korea model

Right View

Left View

Front View

Bottom View

Top View

Back View