DOWNLOAD Sony DSC-WX100 (serv.man2) Service Manual ↓ Size: 6.2 MB | Pages: 27 in PDF or view online for FREE

DSC-WX100_L2

2-2

•  Make sure that the flat cable and flexible board are not cracked 

of bent at the terminal.

  Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, don’t pull at wire of connector. It is 

possible that a wire is snapped.

•  When installing a connector, don’t press down at wire of con-

nector. 

  It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

The charging capacitor is charged up to the maximum 330 V 
potential.
There is a danger of electric shock by this high voltage when the 
capacitor is handled by hand.  The electric shock is caused by the 
charged voltage which is kept without discharging when the main 
power of the unit is simply turned off.  Therefore, the remaining 
voltage must be discharged as described below.

To preparing the short jig, a small clip is attached to each end of 
a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.

1 k

Ω/1 W

Wrap insulating tape.

1 k

Ω/1 W

Wrap insulating tape.

ST-269 Flexible
Board

C901

 

R:1 k

Ω/1 W

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between two points with
the short jig about 10 seconds.

(Part code: 1-215-869-11)

ST-269 Flexible
Board

C901

修理時の注意

•  フラットケーブルおよびフレキシブル基板の端子面に欠け，

折れ等がないことを確認する。

  また，コネクタへの接続は，差し込み不足や斜め差しになら

ないように注意する。

•  コネクタを取り外す時に，線材部（極細）を持って引っ張ると

断線する恐れがありますので，絶対に線材部（極細）を持って
引っ張らないでください。

•  線材部（極細）を押さえながらコネクタを差し込むと，線材部

（極細）が断線する恐れがありますので，絶対に線材部（極細）

には負担をかけないでください。

•  金メッキされているフレキシブル基板には，強い負担をかけ

ないでください。

వ┵ߩ೸߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰෰ߒߡߊߛߐ޿ޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡ޿ࠆ
႐ว߽޽ࠆߩߢᵈᗧߒߡߊߛߐ޿㧕

వ┵ߩ೸߇ࠇߚࡔ࠶ࠠㇱߪࠞ࠶࠻ߒߡ
㒰෰ߒߡߊߛߐ޿ޕ
㧔ࡔ࠶ࠠ⎕ ߇ࠦࡀࠢ࠲ౝߦᱷߞߡ޿ࠆ
႐ว߽޽ࠆߩߢᵈᗧߒߡߊߛߐ޿㧕

ストロボ用充電コンデンサ（C901）の放電

ストロボ用充電コンデンサは最大330Vの電圧で充電され
ています。
この高電圧で充電されたコンデンサに手を触れた場合，
電気ショックを受けます。この高電圧には単にセットの
電源を切っただけでは放電されず，残留しています。こ
のため，下記の方法で残留電圧を放電してください。

ショート治具の準備

ショート治具は1kΩ/1W抵抗（1-215-869-11）の両端に
小型のクリップを接続して作成します。
抵抗器は絶縁テープで完全に覆い電気ショックを受けな
いようにしてください。

1 k

Ω/1 W

⛘✼࠹࡯ࡊߢᏎߊ

1 k

Ω/1 W

⛘✼࠹࡯ࡊߢᏎߊ

ST-269 Flexible
Board

C901

 

R:1 k

Ω/1 W

(Part code: 1-215-869-11)

ࠦࡦ࠺ࡦࠨߩ᡼㔚
ࡈ࡜࠶ࠪࡘ࡙࠾࠶࠻ߩ㔚Ḯࠦࡦ࠺ࡦࠨ
ߩ┵ሶ㑆ࠍ࡚ࠪ࡯࠻ᴦౕߢ⚂⑽㑆
ធ⛯ߔࠆޕ

ST-269 Flexible
Board

C901

DSC-WX100_L2

2-3

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  1 

4-419-297-01 

COVER (170), DC (SILVER)

  1 

4-419-297-11 

COVER (170), DC (BLACK)

  1 

4-419-297-21 

COVER (170), DC (PINK)

  1 

4-419-297-31 

COVER (170), DC (BROWN)

  1 

4-419-297-41 

COVER (170), DC (WHITE)

  2 

4-419-316-01 

SHEET (SW) (170)

  3 

1-490-033-21 

SWITCH BLOCK, CONTROL (SW63150) (BLACK)

  3 

1-490-035-11 

SWITCH BLOCK, CONTROL (SW63170) (SILVER)

  3 

1-490-035-21 

SWITCH BLOCK, CONTROL (SW63170) (PINK)

  3 

1-490-035-31 

SWITCH BLOCK, CONTROL (SW63170) (BROWN)

  3 

1-490-035-41 

SWITCH BLOCK, CONTROL (SW63170) (WHITE)

  4 

4-419-305-01 

CUSHION (170), LCD (Note 2)

  5 

4-419-303-01 

WINDOW (170), LCD (Note 2)

  6 

X-2583-894-1  CABINET REAR 170 SILVER ASSY (SILVER)

  6 

X-2583-895-1  CABINET REAR 170 BLACK ASSY (BLACK)

  6 

X-2583-896-1  CABINET REAR 170 PINK ASSY (PINK)

  6 

X-2583-897-1  CABINET REAR 170 BROWN ASSY (BROWN)

  6 

X-2583-898-1  CABINET REAR 170 WHITE ASSY (WHITE)

  7 

4-430-388-01 

SHEET, LC (170)

  LCD901  1-811-497-11 

PANEL MODULE (PE3-ACM)

  #212 

4-270-114-01 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

  #237 

4-270-114-21 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

  #244 

4-412-769-21 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

  #259 

4-412-769-61 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

1.  Remove to numerical order (

1

 

to

 

3

) in the left figure.

1

  #212/#244 X 4 → #237/#259 X 2

3

2

1 

2

1

1 

When assembling,
adjust the position.

#212

#244

#212

#244

#237

#259

Bottom View

Left View

Right View

#212 (Silver)

SILVER/PINK/WHITE

#244 (Black)

BLACK/BROWN

#237 (Silver)

SILVER/PINK/WHITE

#259 (Black)

BLACK/BROWN

Table 2-1

The screw pointed       is different according to the cabinet's color.

For the combination of cabinet's color and screw, please refer to Table 2-1.

Note 2:  Refer to “Assembly-4:  Attaching Method of LCD 

Cushion (170), LCD Window (170)”.

Note 2:  “Assembly-4:  Attaching Method of LCD Cushion 

(170), LCD Window (170)”を参照してください。

1.4

3.0

#212: M1.4 X 3.0 

(Silver)
4-270-114-01

#237:

2.0

1.4

M1.4 X 2.0
(Silver)
4-270-114-21 

#244: M1.4 X 3.0 

(Black)
4-412-769-21

3.0

1.4

#259: 

2.0

1.4

M1.4 X 2.0
(Black)
4-412-769-61

The changed portions from
Ver. 1.0 are shown in blue.

DSC-WX100_L2

2-4

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  51 

A-1866-135-A  FRONT 170 SILVER BLOCK ASSY (SILVER)

  51 

A-1866-136-A  FRONT 170 BLACK BLOCK ASSY (BLACK)

  51 

A-1866-137-A  FRONT 170 PINK BLOCK ASSY (PINK)

  51 

A-1866-138-A  FRONT 170 BROWN BLOCK ASSY (BROWN)

  51 

A-1866-139-A  FRONT 170  WHITE BLOCK ASSY (WHITE)

  52 

4-419-293-01 

CABINET (L) (170), SIDE (BLACK, SILVER, WHITE)

  52 

4-419-293-11 

CABINET (L) (170), SIDE (PINK, BROWN)

  53 

X-2583-903-1  COVER TERMINAL 170 SILVER ASSY (SILVER)

  53 

X-2583-904-1  COVER TERMINAL 170 BLACK ASSY (BLACK)

  53 

X-2583-905-1  COVER TERMINAL 170 PINK ASSY (PINK)

  53 

X-2583-906-1  COVER TERMINAL 170 BROWN ASSY (BROWN)

  53 

X-2583-907-1  COVER TERMINAL 170 WHITE ASSY (WHITE)

  54 

4-419-295-01 

CABINET (G) (170), SIDE (BLACK, SILVER, WHITE)

  54 

4-419-295-11 

CABINET (G) (170), SIDE (PINK, BROWN)

 55 

1-489-357-11 

FLASH UNIT

  56 

A-1854-924-A  ST-269 FLEXIBLE BOARD, COMPLETE (Note 2)

  57 

4-266-381-01 

SHEET, CABINET UPPER (770)

  58 

4-411-649-01 

RUBBER (150), MICROPHONE

  59 

4-419-308-01 

BASE, SHEET MICROPHONE

  60 

4-419-310-01 

FRAME, SHEET (TOP)

  61 

X-2583-885-1  CABINET UPPER 170 SILVER ASSY (SILVER)

  61 

X-2583-886-1  CABINET UPPER 170 BLACK ASSY (BLACK)

  61 

X-2583-887-1  CABINET UPPER 170 PINK ASSY (PINK)

  61 

X-2583-888-1  CABINET UPPER 170 BROWN ASSY (BROWN)

  61 

X-2583-889-1  CABINET UPPER 170 WHITE ASSY (WHITE)

  62 

4-419-314-01 

SHEET (SY) (170) 

  63 

4-419-320-01 

SHEET (SY), RADIATION 

  64 

4-419-311-01 

FLEXIBLE (170), SHEET (LCD)

  65 

4-419-321-01 

SHEET LE, ELECTROSTATIC

 66 

4-429-146-01  CONDUCTIVE 

TAPE 

A

 67 

4-429-147-01  SPACER 

MF

  68 

4-429-148-01 

SPACER LE (170)

 C901 

1-118-015-11 

CAP, ALUMINIUM ELECT 53uF 330V

  #71 

3-208-537-01 

0+Z M1.4X2 NEW TORASUTA

  #212 

4-270-114-01 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

  #244 

4-412-769-21 

SCREW (M1.4), NEW TRU-STAR, P2 (Note 1)

1.  Remove to numerical order (

1

 

to

 

8

) in the left figure.

2.  The meaning of the sign in left figure is as follows. Be careful when it removes.
 

◇-X

:  Solder

‘

‘

2

3

4

1

7

7

7

6

8

5

 

#212 (Silver)

SILVER/PINK/WHITE

#244 (Black)

BLACK/BROWN

Table 2-1

The screw pointed       is different according to the cabinet's color.

For the combination of cabinet's color and screw, please refer to Table 2-1.

#71: M1.4 X 2.0 

(Red)
3-208-537-01

2.0

1.4

1.4

3.0

#212: M1.4 X 3.0 

(Silver)
4-270-114-01

2

5

#212

#244

Bottom View

#71

Back View

8

7

7

-1

7

-2

#244: M1.4 X 3.0 

(Black)
4-412-769-21

3.0

1.4

Note 2:  Refer to “Assembly-2:  Precaution During of ST-269 

Flexible Board.”.

Note 3:  The Radiation sheet (P) is stuck to the Flexible 

Board on the CD-841 Board.

 

Since this Radiation sheet (P) has strong adhesive 
power, be careful when removing the Main frame 
assy.

Note 2:  “Assembly-2:  Precaution During of ST-269 Flexible 

Board.”を参照してください。

Note 3:  CD-841基板のフレキシブル基板部分には、Radiation 

sheet (P) が貼り付いています。

 

このRadiation sheet (P) は粘着力が強いため、Main 

frame assy を取り外す際は注意してください。

ns : not supplied

DSC-WX100_L2

2-5

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

 101 

4-419-302-01  COVER, 

SP

  102 

(Note 3) 

SERVICE,  BLOCK ASSY

  103 

4-417-084-01 

COVER J (170)

  104 

4-266-365-01 

SHEET METAL (J) (770)

  105 

4-270-064-01 

SHEET, J SPACER (770)

  106 

4-419-301-01 

TERMINAL, SHEET (BT)

  107 

1-883-820-11 

BT-068 FLEXIBLE BOARD

  108 

A-1866-835-A  SY-326 BOARD, COMPLETE (SERVICE)

 109 

4-421-334-01  GASKET 

(U)

  111 

4-419-313-01 

FLEXIBLE, SHEET LENS

  112 

4-421-333-01 

SHEET CD, ELECTROSTATIC

  113 

4-297-557-01 

SHEET (760), J

 BT001 

1-756-710-12 

LITHIUM RECHARGEABLE BATTERY

*BT901  1-780-826-11 

TERMINAL BOARD, BATTERY

  SP901 

1-858-302-61 

LOUDSPEAKER (0.8CM) (Note 2)

1.  Remove to numerical order (

1

 

to

 

4

) in the left figure.

2.  The meaning of the sign in left figure is as follows. Be careful when it removes.
 

◇-X

:  Solder

SY

-326

1

4

3

2

2

‘

-2

‘

When replacing this part, be careful whether
a LOGO is existed or not.

TransferJet logo

交換時にロゴの有無に注意してください。

TransferJetのロゴ

Jet model

Non Jet model

A-1877-780-A  SERVICE, SILVER J BLOCK ASSY
A-1877-781-A  SERVICE, BLACK J BLOCK ASSY
A-1877-782-A  SERVICE, PINK J BLOCK ASSY
A-1877-783-A  SERVICE, BROWN J BLOCK ASSY
A-1877-784-A  SERVICE, WHITE J BLOCK ASSY

(UK, CH, J) (SILVER)
(

US, 

UK, CH, J) (BLACK)

(CH, J) (PINK)
(CH, J) (BROWN)
(UK, CH, J) (WHITE)

A-1877-790-A  SERVICE, SILVER BLOCK ASSY
A-1877-791-A  SERVICE, BLACK BLOCK ASSY
A-1877-792-A  SERVICE, PINK BLOCK ASSY
A-1877-793-A  SERVICE, BROWN BLOCK ASSY
A-1877-794-A  SERVICE, WHITE BLOCK ASSY

(EXCEPT UK, CH, J) (SILVER)
(EXCEPT 

US, 

UK, CH, J) (BLACK)

(EXCEPT CH, J) (PINK)
(EXCEPT CH, J) (BROWN)
(EXCEPT UK, CH, J) (WHITE)

2

2

Note 2:  Refer to “Assembly-1:  Precaution During Speaker Installation.”.

Note 4:  Refer to “Assembly-3: Precaution During of Lens Block.”.

Note 2:  “Assembly-1:  Precaution During Speaker Installation” を参照してください。

Note 4:  “Assembly-3: Precaution During of Lens Block.” を参照してください。

Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
Dispose of used batteries according to the instructions.

電池の交換は、正しく行わないと破裂する恐れがあります。
電池を交換する場合には必ず同じ型名の電池又は同等品と
交換してください。
使用済み電池は、取扱指示に従って処分してください。

Hold here.

Lens Barrier

  Very weak

Zoom Motor

  Very weak

Zoom Motor

  Very weak

Yoke

  Very weak

Yoke

  Very weak

Focus Lens

  Very weak

The changed portions from
Ver. 1.1 are shown in blue.