DOWNLOAD Sony DSC-WX1 (serv.man3) Service Manual ↓ Size: 6.98 MB | Pages: 71 in PDF or view online for FREE

1-2

DSC-WX1_L2

Copies all images in the internal memory to a “Memory Stick Duo” media.

1 Insert a “Memory Stick Duo” media with sufficient free capacity into the 

camera

2 MENU U 

 (Settings) 

U 

 (“Memory Stick” Tool) 

U [Copy] U [OK] 

U [ on the control button

• Use a fully charged battery pack. If you attempt to copy image files using a battery pack with little

remaining charge, the battery pack may run out, causing copying to fail or possibly corrupting the data.

• Images cannot be copied individually.
• The original images in the internal memory are retained even after copying. To delete the contents of the 

internal memory, remove the “Memory Stick Duo” media after copying, then format the internal memory 
([Format] in [Internal Memory Tool]).

• A new folder is created on the “Memory Stick Duo” media and all the data will be copied to it. You 

cannot choose a specific folder and copy images to it.

The data can be copied/erased by the operations on the HOME screen. (When erasing the data, execute formatting the internal memory.)

When replacing the SY-233 board, erase the data in internal memory of the board before replacement.

When replacing the SY-233 board, execute formatting and initialize the internal memory after replacement.

Formats the “Memory Stick Duo” media or the internal memory. A commercially available
“Memory Stick Duo” media is already formatted, and can be used immediately.

1 MENU U 

 (Settings) U 

 (“Memory Stick” Tool) or 

 (Internal

Memory Tool) U [Format] U [OK] U [ on the control button

• Note that formatting permanently erases all data including even protected images.

1-3

DSC-WX1_L2

Usually, the camera has been set so as to disable the data writing from the PC to the internal memory of the camera.
This setting must be changed temporarily when the data is to be written to the internal memory such as a case after the board replacement.
To change settings is enabled with using the writing enabler tool (Write Enable Tool) on the Adjust Manual is activating from the Adjust
Station.

1)

Start the Adjust Manual from the Adjust Station.

2)

Click 

 (Write Enable Tool) button.

3)

Click “Active Write Enable Mode” button.

4)

Upon completion of the setting change, the following message will be displayed.

5)

Return the driver to the original one, and connect the PC to the camera (USB mode: Mass Storage).

6)

Write the data read out into the PC to the internal memory of the camera.

7)

Disconnect the PC from the camera, and turn off the camera.

By turning off the camera, the write enable setting is reset.

1-4

DSC-WX1_L2

When problems occur while the unit is operating, the self-diagnosis
function starts working, and displays on the LCD screen what to
do.
Details of the self-diagnosis functions are provided in the Instruction
manual.

When problems occur while the unit is operating, the LCD screen
shows a 4-digit display consisting of an alphabet and numbers, which
blinks at 3.2 Hz. This 5-character display indicates the “repaired
by:”, “block” in which the problem occurred, and “detailed code”
of the problem.

0 0

3 2

C

Repaired by:

Refer to “1-5-3. Self-diagnosis Code Table”.

Indicates the appropriate
step to be taken.
E.g.
13 ....Format the “Memory Stick Duo”.
32 ....Turn on power again.

Block

Detailed Code

Blinks at 3.2 Hz

C : Corrected by customer
E : Corrected by service

engineer

LCD screen

1-5

DSC-WX1_L2

C

C

E

E

E

E

E

E

E

E

E

Block

Function

1

3

3

2

6

1

6

1

6

2

6

2

6

2

6

2

6

2

9

1

9

2

Detailed

Code

0

1

0

1

0

0

1

0

0

2

1

0

1

1

1

2

2

0

0

1

0

0

Symptom/State

The internal memory has experienced a

 media error.

The internal memory has experienced a
format error.

“Memory Stick Duo” is unformatted.

“Memory Stick Duo” is broken.

“Memory Stick Duo” type error

The camera cannot read or write data
on the “Memory Stick Duo”.

Trouble with hardware

Difficult to adjust focus
(Cannot initialize focus)

Zoom operations fault
(Cannot initialize zoom lens.)

Abnormality of IC for steadyshot.

Lens initializing failure.

Lens overheating (PITCH).

Lens overheating (YAW).

Abnormality of thermistor.

Abnormality when flash is being charged.

Non-standard battery is used.

Self-diagnosis Code

Repaired b

y:

Correction

Turn the power off and on again.

Format the internal memory.

Format the “Memory Stick Duo”.

Insert a new “Memory Stick Duo”.

Insert a supported “Memory Stick Duo”.

Turn the power off and on again, or taking out and inserting the
“Memory Stick Duo” several times.

Turn the power off and on again.

Retry turn the power on by the power switch. If it does not
recover, check the focus reset sensor of lens block (pin rf of
CN401 on the SY-233 board). If it is OK, check the focus motor
drive IC (IC402 on the SY-233 board).

Retry turn the power on by the power switch. Check the zoom
reset sensor of lens block (pin ra of CN401 on the SY-233
board), if zooming is performed when the zoom lever is
operated. If it is OK, check the zoom motor drive IC (IC402 on
the SY-233 board).

Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).

Check or replacement of the IC for steadyshot (IC402 on the SY-
233 board).

Check the HALL element (PITCH) of optical image stabilizer
(pin qf, qh of CN401 on the SY-233 board). If it is OK, check
PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.

Check the HALL element (YAW) of optical image stabilizer (pin
qj

, ql of CN401 on the SY-233 board). If it is OK, check

PITCH/YAW angular velocity sensor (SE403 on the SY-233
board) peripheral circuits.

Check the OIS temp sensor of optical image stabilizer (pin qa,
qs

 of CN401 on the SY-233 board).

Checking of ST-221 board or replacement of ST-221 board.
(Note)

Use the compatible battery only.

After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.