DOWNLOAD Sony DSC-W670 Service Manual ↓ Size: 2.5 MB | Pages: 14 in PDF or view online for FREE

DSC-W670

2-1

Follow the disassembly in the numerical order given.

NOTE:
•  -XX, -X mean standardized parts, so they may have some differences from the original one.
•  Items marked “*” are not stocked since they are seldom required for routine service. Some 

delay should be anticipated when ordering these items.

•  The mechanical parts with no reference number in the exploded views are not supplied.
•  Due to standardization, replacements in the parts list may be different from the parts speci-

fied in the diagrams or the components used on the set.

•  Color Indication of Appearance Parts
 Example:
 

(SILVER) : Cabinet’s Color

 

(Silver) 

: Parts Color

The components identified by mark 

0 or 

dotted line with mark 

0 are critical for safety.

Replace only with part number specified.

Les composants identifiés par une marque 
0 sont critiques pour la sécurité.
Ne les remplacer que par une pièce portant 
le numéro spécifié.

When indicating parts by reference 
number, please include the board name.

• Abbreviation
  CH 

: Chinese model

  HK 

: Hong Kong model

  CND  : Canadian model
  KR 

: Korea model

q;

Lens Block Section

[Disassembly]
[Exploded View]

Right View

Left View

Front View

Bottom View

Top View

Back View

DSC-W670

2-2

•  Make sure that the flat cable and flexible board are not cracked of 

bent at the terminal.

  Do not insert the cable insufficiently nor crookedly.

•  When remove a connector, do not pull at wire of connector. It is 

possible that a wire is snapped.

•  When installing a connector, do not press down at wire of connector. 
  It is possible that a wire is snapped.

•  Do not apply excessive load to the gilded flexible board.

The charging capacitor is charged up to the maximum 310 V
potential.
There is a danger of electric shock by this high voltage 
when the capacitor is handled by hand.  The electric shock 
is caused by the charged voltage which is kept without dis-
charging when the main power of the unit is simply turned 
off.  Therefore, the remaining voltage must be discharged as 
described below.

To preparing the short jig, a small clip is attached to each end 
of a resistor of 1 k

Ω /1 W (1-215-869-11).

Wrap insulating tape fully around the leads of the resistor to 
prevent electrical shock.

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

Cut and remove the part of gilt
which comes off at the point.
(Be careful or some
pieces of gilt may be left inside)

1 k

Ω/1 W

Wrap insulating tape.

1 k

Ω/1 W

Wrap insulating tape.

Note: High-voltage cautions

Note: High-voltage cautions

Discharging the Capacitor
Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate, wrap the short jig with the 
insulation tape.

Short-circuit between the two points with the short jig about 10 seconds.
To avoid the spark with the metal plate, wrap the short jig with the 
insulation tape.

R:1 k

Ω

/1 W 

(Part code: 1-215-869-11)

ST Board

TP2

C+1

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W670

2-3

ns: not supplied

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  1 

X-2583-097-1  COVER ASSY, FRONT (SILVER)

  1 

X-2583-099-1  COVER ASSY, FRONT (BLACK)

  1 

X-2583-100-1  COVER ASSY, FRONT (RED)

  1 

X-2583-101-1  COVER ASSY, FRONT (BLUE)

  1 

X-2583-102-1  COVER ASSY, FRONT (PINK)

  2 

4-409-804-01 

BELT (SVR), ORNAMENTAL (L) (SILVER)

  2 

4-409-805-01 

BELT (BLK), ORNAMENTAL (L) (BLACK)

  2 

4-409-806-01 

BELT (RED), ORNAMENTAL (L) (RED)

  2 

4-409-807-01 

BELT (BLU), ORNAMENTAL (L) (BLUE)

  2 

4-409-809-01 

BELT (PNK), ORNAMENTAL (L) (PINK)

  3 

X-2583-114-1 

COVER ASSY (SILVER), TOP (SILVER)

  3 

X-2583-115-1 

COVER ASSY (BLACK), TOP (BLACK)

  3 

X-2583-116-1 

COVER ASSY (RED), TOP (RED)

  3 

X-2583-117-1 

COVER ASSY (BLUE), TOP (BLUE)

  3 

X-2583-118-1 

COVER ASSY (PINK), TOP (PINK)

 4 

X-2583-104-1  COVER 

ASSY, 

REAR

  5 

4-409-798-01 

BELT (SVR), ORNAMENTAL (R) (SILVER)

  5 

4-409-799-01 

BELT (BLK), ORNAMENTAL (R) (BLACK)

  5 

4-409-800-01 

BELT (RED), ORNAMENTAL (R) (RED)

  5 

4-409-802-01 

BELT (BLU), ORNAMENTAL (R) (BLUE)

  5 

4-409-803-01 

BELT (PNK), ORNAMENTAL (R) (PINK)

 6 

4-409-911-01  COVER, 

DC

  7 

4-419-220-01 

BELT (SILVER), COLOR TONE (SILVER)

  7 

4-419-221-01 

BELT (BLACK), COLOR TONE (BLACK)

  7 

4-419-222-01 

BELT (RED), COLOR TONE (RED)

  7 

4-419-223-01 

BELT (BLUE), COLOR TONE (BLUE)

  7 

4-419-225-01 

BELT (PINK), COLOR TONE (PINK)

 #S1 

4-419-354-01  MACHINE_M1.4_3.5_T0.4_BLK_AB 

(Note)

 #S2 

4-419-355-01  MACHINE_M1.4_3.5_T0.4_SVR_AB 

(Note)

 #S3 

4-419-352-01  MACHINE_M1.4_3_BLK_AB

 #S4 

4-419-351-01  MACHINE_M1.4_4_BLK_AB

 #S5 

4-419-353-01  MACHINE_M1.4_3.6_BLK_AB

 #S6 

4-179-232-01  TAPPING_M1.4_3.5_SVR_AB

1

→ #S4 X 2 → #S5 X 2

2

3

4

1.  Remove to numerical order (

1

 

to

 

6

) in the left figure.

#S5

#S3

#S4

Left View

Right View

Bottom View

#S6

Back View

#S1
#S2

Bottom View

Table 2-1

The screw pointed       is different according to the cabinet's color.

For the combination of cabinet's color and screw, please refer to Table 2-1.

1

4

2

5

6

3

2

3

3

1

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W670

2-4

Ref. No. 

Part No. 

Description

Ref. No. 

Part No. 

Description

  51 

4-419-235-01 

BRACKET, BT CHAMBER

  52 

4-419-244-01 

SPRING, BT HOOK

  53 

4-419-332-01 

SPRING, BATT EJECTION

 54 

4-409-910-01  COVER, 

CAPACITOR

 55 

X-2583-119-1  BRACKET 

ASSY, 

LCD

  56 

A-1852-289-A  ST BOARD ASSY (Note 1)

 57 

A-1852-284-A  SW 

BOARD 

ASSY

  58 

X-2583-914-1  COVER ASSY, LCD (Note 2)

  LCD901  1-802-984-11 

LCD MODULE (Note 2)

 

#S6 4-179-232-01 

TAPPING_M1.4_3.5_SVR_AB

 #S7 

4-179-231-01  MACHINE_M1.4_2_SVR_AB

1.  Remove to numerical order (

1

 

to

 

5

) in the left figure.

5

5

1

2

#S7

Back View

#S6

LCD Module

Back View

#S6

Solder

Back View

Top View

1

3

4

5

2

5

1

2

When remove these solder be careful not to
break the ST Board and Main Board.
Because two boards are jointed by soldering.
And when installing, be careful for solder not
to flow in the contact portion of battery.

The changed portions from
Ver. 1.0 are shown in blue.