Sony DSC-W620 (serv.man2) Service Manual ▷ View online
DSC-W620_ADJ
5-5
5-2-2. Zoom Adjustment
The Zoom Over Run/Focus Back Lash Adjustment order is as follows.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
Perform the Zoom adjustment in the condition the camera stands up in the horizontal plane.
Adjusting in other conditions causes a malfunction of the zoom adjustment.
The adjustment finished normally.
O Zoom Station Passed
The adjustment is complete
The adjustment is finished abnormally.
X Focus backlash NG
X Zoom Adjust NG
X Zoom Adjust NG
Malfunction of Zoom adjust-
ment result
ment result
X Focus backlash NG
Malfunction of Zoom adjust-
ment Focus section
ment Focus section
X Zoom Adjust NG
Malfunction of Zoom adjust-
ment Zoom section
ment Zoom section
Adjustment order
Screen display
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in the horizontal plane.
Press the control button “ V (Key Down)”, then Zoom Adjustment starts.
on the screen. (Fig. 5-2-15)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-16 to 5-2-18)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
5-2-3. Far Focus Adjustment
Note:
When using the Flange back adjustment jig, take care of the following points:
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
• For the illumination, use a light source such as an incandescent lamp or inverter type fluorescent light free from flickering.
• Do not make an adjustment in the environment where fluorescent lamp flickering occurs even if the illuminance can be ensured with the room
illumination only.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
Use an incandescent lamp or inverter type fluorescent light at a place free from the influence of room illumination.
1) Install the Flange back adjustment jig so that the distance between
it and the front of lens of camera is 3 cm or less.
Note:
Note:
Take care not to hit the Flange back adjustment jig when extend-
ing the lens.
2) Make the height of Flange back adjustment jig and the camera equal.
3) Check that the center of chart meets the center of shot image screen
with the zoom lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Far Focus Station Passed
Please Key MENU Enter...
Please Key MENU Enter...
The adjustment is complete
The adjustment is finished abnormally.
X Far Focus NG !
Please ReAdjust Far Focus
Please ReAdjust Far Focus
Malfunction of Far Focus adjust-
ment
ment
Adjustment order
Screen display
3 cm or less
Equipment required: Flange back adjustment jig
Flange back adjustment jig
Camera
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Flange back adjustment jig. (Fig. 5-2-19)
Press the control button “ b (Key Left)”, then Far Focus Adjustment starts.
In case of the adjustment is finished normally,
the adjustment completion indication appears
on the screen. (Fig. 5-2-20)
Turn off the power to quit the adjustment mode.
the adjustment completion indication appears
on the screen. (Fig. 5-2-20)
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
In case of the adjustment is finished abnormally,
(Fig. 5-2-21)
In this case, confirm the adjusting environment
and readjust.
In this case, confirm the adjusting environment
and readjust.
Fig. 5-2-15
Fig. 5-2-16
Fig. 5-2-17
Fig. 5-2-18
Fig. 5-2-19
Fig. 5-2-20
Fig. 5-2-21
DSC-W620_ADJ
5-6
5-2-4. Near Focus Adjustment
Note:
Perform the Near Focus Adjustment after the Far Focus Adjustment.
1) Be sure to set 50 ± 1 cm distance between the chart and the tip of camera lens.
2) Check that the center of chart meets the center of shot image screen with the zoom
lens at TELE end and WIDE end respectively.
Color temperature = 5000 ± 300K
Be sure not to turn off the power during adjusting.
The adjustment finished normally.
O Near Focus Station Passed
Please Key MENU Enter...
Please Key MENU Enter...
The adjustment is complete
The adjustment is finished abnormally.
X Near Focus NG !
Please ReAdjust Far Focus
Please ReAdjust Far Focus
Malfunction of Near Focus ad-
justment
justment
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Chart. (Fig. 5-2-22)
Press the control button “ B (Key Right)”, then Near Focus Adjustment starts.
on the screen. (Fig. 5-2-23)
In case of the adjustment is finished normally,
the adjustment completion indication appears
the adjustment completion indication appears
Turn off the power to quit the adjustment mode.
(Fig. 5-2-24)
In case of the adjustment is finished abnormally,
the following indication appears on the screen.
the following indication appears on the screen.
In this case, confirm the adjusting environment
and readjust.
In case of the Near Focus adjustment is failed,
readjust the Far Focus adjustment and try to
readjust the Near Focus adjustment.
and readjust.
In case of the Near Focus adjustment is failed,
readjust the Far Focus adjustment and try to
readjust the Near Focus adjustment.
Screen display
5-2-5. White Balance Adjustment
The White Balance Adjustment is as follows.
Small pattern box (PTB-1450) setting:
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
Color temperature = 3150 ± 50K
Luminance: LV12.3 ± 0.2
The adjustment finished normally.
O WB OK
The adjustment is complete
The adjustment is finished abnormally.
X Cap WB NG
Malfunction of Cap White Bal-
ance adjustment
ance adjustment
X Pre WB NG
Malfunction of Pre White Bal-
ance adjustment
ance adjustment
X WB NG
Malfunction of White Balance
adjustment
adjustment
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Place the camera in front of the Small pattern box (PTB-1450). (Fig. 5-2-25)
Press the control button “ z (Key OK)”, then White Balance Adjustment starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-26)
on the screen. (Fig. 5-2-26)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-27 to 5-2-29)
(Fig. 5-2-27 to 5-2-29)
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
and readjust.
and readjust.
Screen display
Chart
Camera
Equipment required: Chart
50 ± 1 cm
Equipment required: Small pattern box (PTB-1450)
Small pattern box
(PTB-1450)
(PTB-1450)
0.5 to 1.0 cm
Black cloth
Camera
Clear chart
Fig. 5-2-22
Fig. 5-2-25
Fig. 5-2-23
Fig. 5-2-24
Fig. 5-2-26
Fig. 5-2-27
Fig. 5-2-28
Fig. 5-2-29
X Need reAdjust CCD
Note:
If this screen appears, perform the following procedure to make the
adjustment again.
Readjustment restores normal state of the unit.
1. Turn off the unit.
2. Take the battery out of the unit.
3. Load the battery in the unit and start the unit in the Adjustment
2. Take the battery out of the unit.
3. Load the battery in the unit and start the unit in the Adjustment
mode.
4. Make the adjustment again.
DSC-W620_ADJ
5-7E
Selectable language table
5-2-6. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the SD-Card or
Save “lang.txt” in the root directory of the SD-Card or
Memory Stick PRO Duo
being used.
The content of “lang.txt” is as follows:
Language Destination (for example: E37) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (7bit) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (7bit) (enter key)
The following is an example of E37 Language Destination Setting for DSC-W620 Silver camera.
E37
0080800806
0120243
0080800806
0120243
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3) The S/N must be 7 bit. It refer to the serial number of shipment.
The adjustment is finished abnormally.
Read Language NG!
Malfunction of Set Language
Destination
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Destination is failed, reset the
language destination.
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the Shutter button (Key S1), then Language Destination Setting starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-30)
on the screen. (Fig. 5-2-30)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-31)
(Fig. 5-2-31)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
Screen display
5-3. PRODUCT ID LIST
The adjustment finished normally.
Encryption:
Set LangDestination OK!
The adjustment is complete
Note:
The screen above is an example.
Note:
The screen above is an example.
Fig. 5-2-30
Fig. 5-2-31
DSC-W620
Area
Color
Product ID
U2
Silver
80800834
Black
80800835
Red
80800836
CA2
Silver
80800840
Black
80800841
Red
80800842
CEE2
Black
80800865
CEE8
Silver
80800850
Black
80800863
Red
80800893
CEH
Black
80800861
Red
80800862
E32
Silver
80800810
Black
80800870
Red
80800886
E33
Silver
80800811
Black
80800871
Red
80800887
DSC-W620
Area
Color
Product ID
E37
Silver
80800806
Black
80800807
Red
80800808
EA8
Silver
80800819
Black
80800829
Red
80800879
HK1
Silver
80800813
Black
80800873
Red
80800889
CN2
Silver
80800875
Black
80800876
Red
80800877
KR2
Silver
80800880
Black
80800881
Red
80800882
DESTINA
TION
AREA
SELECTABLE LANGUAGE
VIDEO OUT
Default
Japanese
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
Ukrainian
U2
US
z
a
a
a
NTSC
CA2
CND
z
a
a
a
a
NTSC
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEH
UK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
E37
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
EA8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
HK1
HK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CN2
CH
a
a
a
a
a
z
a
a
a
a
a
a
a
a
PAL
KR2
KR
a
a
a
a
a
a
a
a
z
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
DSC-W620_ADJ
5-7E
Selectable language table
5-2-6. Set Language Destination
Language Destination Setting:
Save “lang.txt” in the root directory of the SD-Card or
Save “lang.txt” in the root directory of the SD-Card or
Memory Stick PRO Duo
being used.
The content of “lang.txt” is as follows:
Language Destination (for example: E37) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (7bit) (enter key)
Product ID (10bit) (enter key) (refer to “5-3 PRODUCT ID LIST”)
S/N (7bit) (enter key)
The following is an example of E37 Language Destination Setting for DSC-W620 Silver camera.
E37
0080800806
0120243
0080800806
0120243
Especially Attention:
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
1) The enter key must be the end symbol of each row.
2) For the Product ID, refer to “5-3 PRODUCT ID LIST”, and the Product ID must be 10bit.
If the Product ID is less than 10 bit, add 0 before the Product ID.
3) The S/N must be 7 bit. It refer to the serial number of shipment.
The adjustment is finished abnormally.
Read Language NG!
Malfunction of Set Language
Destination
Destination
In case of the Set Language
Destination is failed, reset the
language destination.
Destination is failed, reset the
language destination.
Adjustment order
Set the camera to the adjustment mode.
Confirm the indication
on the screen.
Finished normally.
Finished abnormally.
* For the setting procedure of the adjustment mode, refer to “5-1-5. Setting the Adjustment Mode” (Page 5-3).
Press the Shutter button (Key S1), then Language Destination Setting starts.
the adjustment completion indication appears
on the screen. (Fig. 5-2-30)
on the screen. (Fig. 5-2-30)
In case of the adjustment is finished normally,
Turn off the power to quit the adjustment mode.
the following indication appears on the screen.
(Fig. 5-2-31)
(Fig. 5-2-31)
and readjust.
In case of the adjustment is finished abnormally,
In this case, confirm the adjusting environment
Screen display
5-3. PRODUCT ID LIST
The adjustment finished normally.
Encryption:
Set LangDestination OK!
The adjustment is complete
Note:
The screen above is an example.
Note:
The screen above is an example.
Fig. 5-2-30
Fig. 5-2-31
DSC-W620
Area
Color
Product ID
U2
Silver
80800834
Black
80800835
Red
80800836
CA2
Silver
80800840
Black
80800841
Red
80800842
CEE2
Black
80800865
CEE8
Silver
80800850
Black
80800863
Red
80800893
CEH
Black
80800861
Red
80800862
E32
Silver
80800810
Black
80800870
Red
80800886
E33
Silver
80800811
Black
80800871
Red
80800887
DSC-W620
Area
Color
Product ID
E37
Silver
80800806
Black
80800807
Red
80800808
EA8
Silver
80800819
Black
80800829
Red
80800879
HK1
Silver
80800813
Black
80800873
Red
80800889
CN2
Silver
80800875
Black
80800876
Red
80800877
KR2
Silver
80800880
Black
80800881
Red
80800882
DESTINA
TION
AREA
SELECTABLE LANGUAGE
VIDEO OUT
Default
Japanese
English
French
German
Spanish
Italian
Portuguese
Brazilian Portuguese
Simplified Chinese
T
raditional Chinese
Arabic
Dutch
Russian
Swedish
Korean
Norwegian
Danish
Finnish
Polish
Hungarian
Czech
Persian
Thai
Greek
T
urkish
Malay
Croatian
Romanian
Indonesian
Bulgarian
V
ietnamese
Ukrainian
U2
US
z
a
a
a
NTSC
CA2
CND
z
a
a
a
a
NTSC
CEE2
AEP
a
a
a
a
a
a
a
z
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEE8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CEH
UK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E32
E
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
E33
a
a
z
a
a
a
a
a
a
a
a
a
a
a
NTSC
E37
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
EA8
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
HK1
HK
z
a
a
a
a
a
a
a
a
a
a
a
a
a
PAL
CN2
CH
a
a
a
a
a
z
a
a
a
a
a
a
a
a
PAL
KR2
KR
a
a
a
a
a
a
a
a
z
a
a
a
a
a
NTSC
z
: INITIAL LANGUAGE
Display
