DOWNLOAD Sony DSC-W580 (serv.man2) Service Manual ↓ Size: 7.1 MB | Pages: 21 in PDF or view online for FREE

DSC-W580_L2

1-3

When “FLASH error” (Self-diagnosis Code E : 91 : 01) occurs, to prevent any abnormal situation caused by high voltage, setting of the flash is changed 
automatically to disabling charge and flash setting.
After fixing, this setting needs to be deactivated. Flash error code can be initialized by the operations on the HOME screen.

Initializes the setting to the default setting.  

Even if you execute this function, the images are retained. 

1. MENU 

 

 (Settings) 

 

 (Main Settings) 

 [Initialize] 

 [OK] 

 

Be sure not to turn off the camera while initializing. 

Self-diagnosis Code

Symptom/State

Correction

Repaired by:

Block

Function

Detailed

Code

C

1

3

0

1

The internal memory has experienced a me-
dia error.

Turn the power off and on again.

The internal memory has experienced a for-
mat error.

Format the internal memory.

Memory card is unformatted.

Format the memory card.

Memory card is broken.

Insert a new memory card.

Memory card type error

Insert a supported memory card.

The camera cannot read or write data on the 
memory card.

Turn the power off and on again, or taking out and inserting the memory 
card several times.

C

3

2

0

1

Trouble with hardware

Turn the power off and on again.

E

6

1

0

0

Difficult to adjust focus
(Cannot initialize focus)

Retry turn the power on by the power switch. If it does not recover, 
check the focus reset sensor of lens block (pin wk of CN401 on the 
SY-274 board). If it is OK, check the focus motor drive IC (IC401 on 
the SY-274 board).

E

6

1

1

0

Zoom operations fault
(Cannot initialize zoom lens.)

Retry turn the power on by the power switch. Check the zoom reset 
sensor of lens block (pin eg of CN401 on the SY-274 board) when 
zooming is performed when the zoom button is operated. If it is OK, 
check the zoom motor drive IC (IC401 on the SY-274 board).

E

6

2

0

2

Abnormality of IC for steadyshot.

Check of the IC for steadyshot (IC401 on the SY-274 board).

E

6

2

1

0

Lens initializing failure.

Check of the IC for steadyshot (IC401 on the SY-274 board).

E

6

2

2

0

Abnormality of thermistor.

Check the OIS temp sensor of optical image stabilizer (pin wa of 
CN401 on the SY-274 board).

E

6

2

1

1

Lens overheating (PITCH).

Check the HALL element (PITCH) of optical image stabilizer (pin qf, 
qh

 of CN401 on the SY-274 board). If it is OK, check PITCH angular 

velocity sensor (SE401 on the SY-274 board) peripheral circuits.

E

6

2

1

2

Lens overheating (YAW).

Check the HALL element (YAW) of optical image stabilizer (pin qd, 
qa

 of CN401 on the SY-274 board). If it is OK, check YAW angular 

velocity sensor (SE401 on the SY-274 board) peripheral circuits.

E

9

1

0

1

Abnormality when flash is being charged.

Checking of flash unit or replacement of flash unit. (Note)

E

9

4

0

0

Internal memory fault

Inspect the internal memory (IC201 on the SY-274 board).

Note: After repair, be sure to perform “1-6. PROCESS AFTER FIXING FLASH ERROR”.

The changed portions from
Ver. 1.0 are shown in blue.

DSC-W580_L2

1-4

A

Barrier Assy

Claws

Claws

Hole

Barrier Assy

Claws

Claws

Barrier

Lever

3

4

Installation
1

2

5

Removal
1

2

3

4

Barrier Tape

Dent

Ornamental Ring A

Barrier Assy

Barrier Tapes

Barrier Tape

Barrier Tape

Ornamental Ring A

Solvent

Tweezers

Disengage the four claws and remove the Barrier Assy.

Fit the four claws while inserting the Barrier Lever into the hole and attach the Barrier Assy.
Affix two Barrier Tapes to the Barrier Assy so that the end of each Barrier Tape touches the dent.
Note: The Barrier Tapes must not be wrinkled.

Peel off the release papers of the Barrier Tapes.
Install the Ornamental Ring A and press it lightly.

Turn on the power switch and extend the lens (WIDE end).
Detach the battery.
Apply alcohol to two gaps A of the Ornamental Ring A with tweezers or a fine-tipped stick as shown below.
Turn the Ornamental Ring A clockwise and counterclockwise to detach it.

Removal
1

2

Screw

Optical Stepping
Motor (F1430)

Solders

Install
1

2

Screw

Optical Stepping
Motor (F1430)

Groove

Projection
of worm

Solders

Remove the screw.
Unsolder the four locations of the Optical Stepping Motor (F1430) to detach it.

Solder the four locations of the Optical Stepping Motor (F1430).
Install the Optical Stepping Motor (F1430) with a screw.
*Tightening torque = 0.0xx

± 0.0xN • m (0.x ± 0.xkgf • cm)

Note:
Install the Optical Stepping Motor (F1430) while fitting the groove with the projection of worm.

DSC-W580_L2

1-5

5

6

7

1

2

3

4

Remove the Rear Mirror Plate.
Remove the Gear B (Black) and the Gear A (White).
Remove the two screws, and remove soldering from the two points, and then remove the DC Motor (A) Block Assy.

Claws

Screws

Screws

Rear Mirror

Plate

DC Motor Worm

(A) Block Assy

Solders

Screws

Gear B

(Black)

Gear A

(White)

Sensor

Sensor

Claw

Boss

Rib

Rib

Claw

Disconnect the Iris Flexible Board
from LF-115 Flexible Board.

Top View

FG Leaf

Spring

Boss

Claws

FPC Retainer

Back View

Rib

LF-115 Flexible Board

Disengage the two claws and remove the FG Leaf Spring.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.

Remove the LF-115 Flexible Board.

1

2

3

4

Solder the two locations.
Install the DC Motor Worm (A) Block Assy and secure it with two screws.
*Tightening torque = 0.0xx

± 0.0xN • m (0.x ± 0.xkgf • cm)

Install the Gear B (Black) and the Gear A (White).
Install the Rear Mirror Plate and secure it with two screws.
*Tightening torque = 0.0xx

± 0.0xN • m (0.x ± 0.xkgf • cm)

Install the LF-115 Flexible Board.

Install the FPC Retainer while fitting the three claws and the boss.
Install the two Sensors
Install the FG Leaf Spring while fitting the two claws..

6

7

8

Claws

Sensor

Sensor

FG Leaf Spring

Boss

FPC Retainer

Claw

Boss

Rib

Rib

Claw

Disconnect the Iris Flexible Board

from LF-115 Flexible Board.

Top View

Back View

5

Screws

Screws

Rear Mirror Plate

DC Motor Worm

(A) Block Assy

Solders

Screws

Gear B

(Black)

Gear B

(Black)

Gear D

(Black)

Naruto

Gear

Gear A

(White)

Gear A

(White)

Gear C

(White)

Claws

Rib

LF-115 Flexible Board

DSC-W580_L2

1-6

5

6

1

2

3

4

Claws

Sensor

Sensor

Claw

Boss

Rib

Rib

Rib

Claw

Disconnect the Iris Flexible Board

from LF-115 Flexible Board.

LF-115 Flexible Board

Top View

FG Leaf

Spring

Boss

Claws

FPC Retainer

Back View

Gear B

(Black)

Gear D

(Black)

Gear A

(White)

Gear C

(White)

Naruto

Gear

Screws

Rear Mirror

Plate

Screws

Disengage the two claws and remove the FG Leaf Spring.
Remove the two Sensors.
Disengage the three claws and remove the FPC Retainer.

Remove the LF-115 Flexible Board.

Remove the four screws to detach the Rear Mirror Plate
Remove the Gear B (Black), Gear A (White), Gear C (White), Gear D (Black), and Naruto Gear.

7

8

9

Iris Flexible Board

Cutout

Main Assy (A)

Rotary Tube

Block Assy

3 Group Spring

3 Group Frame

Block Assy

Tube

Lubricating

q;

qa

Main Assy (B)

Tube Lubricating

Block Assy

Shield Ring (C)

Remove the 3 Group spring and remove the 3 Group Frame Block Assy..

Turn the Tube Lubricating to the TELE state and remove the Iris Flexible Board from the cutout.

Remove the Main Assy (A) in the WIDE state.

Remove the Main Assy (B).
Remove the Tube Lubricating Block Assy and the Shield Ring (C) from the Rotary Tube Block Assy.