Sony DSC-W550 (serv.man2) Service Manual ▷ View online
DSC-W550_L2
3-1E
3. ASSEMBLY
Assembly-1: Installation Method of Battery Terminal Board
Insert the battery terminal board into a slit in
BT holder to install.
* Battery terminal board is attached with
BT holder to install.
* Battery terminal board is attached with
notch for installation.
Remove the battery terminal board by
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
Fold the notch 3 or 4 times repeatedly to break.
Remove the notch.
Notch
Battery terminal board
Battery terminal board
Notch
Battery terminal
board
board
Notch
Assembly-2: Insulating Sheet (670) Putting Position
SY-284
Insulating Sheet (670)
SY-284 Board
Insulating Sheet (670)
Assembly-3: Precaution During of MA-473 Flexible Board
Installation.
Speaker
Harness
Harness
Tape SP
Route the speaker harness and microphone
harness as shown below.
harness as shown below.
Microphone
Harness
Harness
Microphone
Harness
Harness
MA-473 Flexible
Board
Board
MA-473 Flexible
Board
Board
Assembly-4: Precaution During of Cabinet (Rear) Assy
Installation.
Align the slide switch at the camera mode,
when install cabinet (rear) assy.
when install cabinet (rear) assy.
Slide Switch
Cabinet (Rear) Assy
Assembly-5: Attaching Method of LCD Cushion (710),
LCD Window (620)
Apply LCD cushion (620).
And have the Tab of the Release Paper and peel it off.
And have the Tab of the Release Paper and peel it off.
Attach Cabinet (Rear) Assy to set.
Cabinet (Rear) Assy
Mike Lid (710)
Fit LCD Window (620) into the flame of
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
LCD Cushion (710)
LCD Window (620)
Rear Cabinet Assy
Blow the air before attaching.
Be sure to keep away from dust.
Be sure to keep away from dust.
Align corner of
LCD cushion (710)
with corner of LCD.
LCD cushion (710)
with corner of LCD.
LCD Cushion (710)
LCD
Tab
Release Paper
DSC-W550_L2
3-1E
3. ASSEMBLY
Assembly-1: Installation Method of Battery Terminal Board
Insert the battery terminal board into a slit in
BT holder to install.
* Battery terminal board is attached with
BT holder to install.
* Battery terminal board is attached with
notch for installation.
Remove the battery terminal board by
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
Fold the notch 3 or 4 times repeatedly to break.
Remove the notch.
Notch
Battery terminal board
Battery terminal board
Notch
Battery terminal
board
board
Notch
Assembly-2: Insulating Sheet (670) Putting Position
SY-284
Insulating Sheet (670)
SY-284 Board
Insulating Sheet (670)
Assembly-3: Precaution During of MA-473 Flexible Board
Installation.
Speaker
Harness
Harness
Tape SP
Route the speaker harness and microphone
harness as shown below.
harness as shown below.
Microphone
Harness
Harness
Microphone
Harness
Harness
MA-473 Flexible
Board
Board
MA-473 Flexible
Board
Board
Assembly-4: Precaution During of Cabinet (Rear) Assy
Installation.
Align the slide switch at the camera mode,
when install cabinet (rear) assy.
when install cabinet (rear) assy.
Slide Switch
Cabinet (Rear) Assy
Assembly-5: Attaching Method of LCD Cushion (710),
LCD Window (620)
Apply LCD cushion (620).
And have the Tab of the Release Paper and peel it off.
And have the Tab of the Release Paper and peel it off.
Attach Cabinet (Rear) Assy to set.
Cabinet (Rear) Assy
Mike Lid (710)
Fit LCD Window (620) into the flame of
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
LCD Cushion (710)
LCD Window (620)
Rear Cabinet Assy
Blow the air before attaching.
Be sure to keep away from dust.
Be sure to keep away from dust.
Align corner of
LCD cushion (710)
with corner of LCD.
LCD cushion (710)
with corner of LCD.
LCD Cushion (710)
LCD
Tab
Release Paper
DSC-W550_L2
3-1E
3. ASSEMBLY
Assembly-1: Installation Method of Battery Terminal Board
Insert the battery terminal board into a slit in
BT holder to install.
* Battery terminal board is attached with
BT holder to install.
* Battery terminal board is attached with
notch for installation.
Remove the battery terminal board by
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
Fold the notch 3 or 4 times repeatedly to break.
Remove the notch.
Notch
Battery terminal board
Battery terminal board
Notch
Battery terminal
board
board
Notch
Assembly-2: Insulating Sheet (670) Putting Position
SY-284
Insulating Sheet (670)
SY-284 Board
Insulating Sheet (670)
Assembly-3: Precaution During of MA-473 Flexible Board
Installation.
Speaker
Harness
Harness
Tape SP
Route the speaker harness and microphone
harness as shown below.
harness as shown below.
Microphone
Harness
Harness
Microphone
Harness
Harness
MA-473 Flexible
Board
Board
MA-473 Flexible
Board
Board
Assembly-4: Precaution During of Cabinet (Rear) Assy
Installation.
Align the slide switch at the camera mode,
when install cabinet (rear) assy.
when install cabinet (rear) assy.
Slide Switch
Cabinet (Rear) Assy
Assembly-5: Attaching Method of LCD Cushion (710),
LCD Window (620)
Apply LCD cushion (620).
And have the Tab of the Release Paper and peel it off.
And have the Tab of the Release Paper and peel it off.
Attach Cabinet (Rear) Assy to set.
Cabinet (Rear) Assy
Mike Lid (710)
Fit LCD Window (620) into the flame of
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
LCD Cushion (710)
LCD Window (620)
Rear Cabinet Assy
Blow the air before attaching.
Be sure to keep away from dust.
Be sure to keep away from dust.
Align corner of
LCD cushion (710)
with corner of LCD.
LCD cushion (710)
with corner of LCD.
LCD Cushion (710)
LCD
Tab
Release Paper
DSC-W550_L2
3-1E
3. ASSEMBLY
Assembly-1: Installation Method of Battery Terminal Board
Insert the battery terminal board into a slit in
BT holder to install.
* Battery terminal board is attached with
BT holder to install.
* Battery terminal board is attached with
notch for installation.
Remove the battery terminal board by
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
bending the claw of rock portion.
When assembling the battery terminal board,
replace it with new one because battery ]
terminal board will be bent.
Fold the notch 3 or 4 times repeatedly to break.
Remove the notch.
Notch
Battery terminal board
Battery terminal board
Notch
Battery terminal
board
board
Notch
Assembly-2: Insulating Sheet (670) Putting Position
SY-284
Insulating Sheet (670)
SY-284 Board
Insulating Sheet (670)
Assembly-3: Precaution During of MA-473 Flexible Board
Installation.
Speaker
Harness
Harness
Tape SP
Route the speaker harness and microphone
harness as shown below.
harness as shown below.
Microphone
Harness
Harness
Microphone
Harness
Harness
MA-473 Flexible
Board
Board
MA-473 Flexible
Board
Board
Assembly-4: Precaution During of Cabinet (Rear) Assy
Installation.
Align the slide switch at the camera mode,
when install cabinet (rear) assy.
when install cabinet (rear) assy.
Slide Switch
Cabinet (Rear) Assy
Assembly-5: Attaching Method of LCD Cushion (710),
LCD Window (620)
Apply LCD cushion (620).
And have the Tab of the Release Paper and peel it off.
And have the Tab of the Release Paper and peel it off.
Attach Cabinet (Rear) Assy to set.
Cabinet (Rear) Assy
Mike Lid (710)
Fit LCD Window (620) into the flame of
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
Cabinet (Rear) Assy and attach it on LCD Cushion (710).
LCD Cushion (710)
LCD Window (620)
Rear Cabinet Assy
Blow the air before attaching.
Be sure to keep away from dust.
Be sure to keep away from dust.
Align corner of
LCD cushion (710)
with corner of LCD.
LCD cushion (710)
with corner of LCD.
LCD Cushion (710)
LCD
Tab
Release Paper
